Craftsman WEEDWACKER Incredi-Pull 316.796170 Operator's Manual page 3

• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Be in the starting position
whenever pulling the starter rope. The operator and unit
must be in a stable position while starting. Refer to
Starting/Stopping Instructions.
• Use the right tool. Only use this tool for its intended purpose.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating. Keep
a firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving parts.
Do not touch or try to stop the cutting attachment when it rotates.
• Do not touch the engine, gear housing or muffler. These
parts get extremely hot from operation, even after the unit is
turned off.
• Do not operate the engine faster than the speed needed to
cut, trim or edge. Do not run the engine at high speed when
not cutting.
• Always stop the engine when cutting is delayed or when
walking from one cutting location to another.
• If you strike or become entangled with a foreign object, stop
the engine immediately and check for damage. Do not
operate before repairing damage. Do not operate the unit
with loose or damaged parts.
• Stop the unit, switch the engine to off, and disconnect the
spark plug for maintenance or repair.
• Use only replacement parts or accessories recommended for
this tool that are distributed by Sears or a Craftsman outlet.
Use of any replacement parts or accessories purchased
elsewhere may be hazardous, and will also void your warranty.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment and shield.
• To reduce fire hazard, replace a faulty muffler and spark
arrestor. Keep the engine and muffler free from grass, leaves,
excessive grease or carbon build up.
OTHER SAFETY WARNINGS
• Never store the unit with fuel in the tank, inside a building
where fumes may reach an open flame (pilot lights, etc.) or
sparks (switches, electrical motors, etc.).
• Allow the engine to cool before storing or transporting. Be
sure to secure the unit while transporting.
• Store the unit in a dry area, locked up or up high to prevent
unauthorized use or damage, out of the reach of children.
• Never douse or squirt the unit with water or any other liquid.
Keep handles dry, clean and free from debris. Clean after
each use, see Cleaning and Storage Instructions.
• Keep these instructions. Refer to them often and use them to
instruct other users. If you loan someone this unit, also loan
them these instructions.
SAVE THESE INSTRUCTIONS
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the
operator's manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL MEANING SYMBOL MEANING
• SAFETY ALERT SYMBOL
Indicates danger, warning or caution. May
be used in conjunction with other symbols or
pictographs.
WARNING - READ OPERATOR'S MANUAL
Read the operator's manual(s) and follow all
warnings and safety instructions. Failure to do
so can result in serious injury to the operator
and/or bystanders.
• WEAR EYE AND HEARING PROTECTION
WARNING: Thrown objects and loud noise
can cause severe eye injury and hearing loss.
Wear eye protection meeting ANSI Z87.1
standards and ear protection when operating
this unit. Use a full face shield when needed.
• HOT SURFACE WARNING
Do not touch a hot muffler, gear housing or
cylinder. You may get burned. These parts get
extremely hot from operation. They remain hot
short time after the unit is turned off.
WARNING: Keep all bystanders, especially
Children and petsl at least 50 feet (!5 m)
from the 0perating area.
"_l m _= • CHOKE CONTROL
_ _ i.- FULL ch0ke p0sition
2. •PARTIAL choke position
3.-RUN chekeposition
_O ' THROWN OBJECTSAND ROTATING
CUTTER CAN CAUSE SEVERE INJURy
_-'*_ WARNING: Do not operate without the
_/,_ cutting attachment shield in place. Keep
_f _ away from the rotating cutting attachment,
,SHARP BLADE
WARNING: Sharp blade on cutting
_.,_ attachment shield. To prevent serious injury,
do not touch the line cutting blade.
• UNLEADED FUEL
Always use clean, fresh unleaded fuel
• OIL
_Z_/-_ Refer to operator's manual for the proper
type of oiJ