Audio Delay - Marantz NR1604 Owner's Manual

Audio Delay

While viewing video, manually adjust the time to delay audio output so that the video and audio are
synchronized.
0ms – 200ms
• This item can be set within the range of 0 to 100 ms when "Auto Lip Sync" (vpage 115) is set to
"On" and when a TV compatible with Auto Lip Sync is connected.
• Store "Audio Delay" for each input source.
• Audio Delay for game mode can be set when "Video Mode"
"Game".
Volume
Set the MAIN ZONE (room where the unit is located) volume setting.
Setting items
Scale 0 – 98 : Display in the range 0 (Min) to 98.
–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.
Set how volume is
displayed.
• The "Scale" setting is applied also to the "Limit" and "Power On Level"
display method.
• The "Scale" setting applies to all zones.
Limit 60 (–20dB) / 70 (–10dB) / 80 (0dB)
Make a setting for Off : Do not set a maximum volume.
maximum volume.
Power On Level Last : Use the memorized setting from the last session.
Mute : Always use the muting on condition when power is turned on.
Define the volume setting
that is active when the 1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.
power is turned on.
Mute Level Full : The sound is muted entirely.
–40dB : The sound is attenuated by 40 dB down.
Set the amount of
attenuation when muting –20dB : The sound is attenuated by 20 dB down.
is on.
DVD
Default settings are underlined.
Setting details
(vpage 116) is set to "Auto" or
Default settings are underlined.
Setting details
Audyssey
Set Audyssey MultEQ ® , Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . These can be selected
after Audyssey ® Setup has been performed. For additional information on Audyssey technology, please
see page 150.
NOTE
• If you have not performed Audyssey ® Setup, or if you change the speaker settings after performing
Audyssey ® Setup, you may not be able to select Dynamic EQ/Dynamic Volume.
In this case, either perform Audyssey ® Setup over again or perform "Restore..." (vpage 28) to return
to the settings after Audyssey ® Setup was run.
• When HD Audio for which the sampling frequency exceeds 96 kHz is played back, the "Audyssey"
cannot be set.
Setting items
MultEQ ®
Audyssey : Optimize the frequency response of all speakers.
MultEQ ® compensates for
Audyssey Byp. L/R : Optimize frequency response of speakers except
both time and frequency front L and R speakers.
Audyssey Flat : Optimize frequency response of all speakers to flat
characteristics of the
listening area based on response.
Audyssey ® Setup
Graphic EQ : Apply frequency response set with "Graphic EQ"
measurement results. (vpage 113).
Off : Turn "MultEQ ® " equalizer off.
Selection is done from three
types of compensation
curves. We recommend the
"Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be selected
"Audyssey" setting.
after Audyssey ® Setup has been performed. "Audyssey" is automatically
MultEQ ® is the prerequisite
selected after performing Audyssey ® Setup. When "Audyssey", "Audyssey
function for Dynamic EQ
Byp. L/R" or "Audyssey Flat" is selected,
and Dynamic Volume.
NOTE
When using headphones, "MultEQ ® " is automatically set to "Off".
"MultEQ ® ", "Dynamic EQ" and "Dynamic Volume" settings are stored for each input source.
112
Audio
Default settings are underlined.
Setting details
illuminates.
v See overleaf