Page 1 AV Surround Receiver NR1604 Owner’s Manual...
Page 2: Safety Precautions
The exclamation point within an equilateral triangle is intended approved by Marantz may void your authority, granted by the FCC, to use 10. Protect the power cord from being walked on or pinched particularly at to alert the user to the presence of important operating the product.
Page 3: Notes On Use
n CAUTIONS ON INSTALLATION NOTES ON USE WARNINGS • Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack. • Handle the power cord carefully. Hold the plug when unplugging the cord. • Keep the unit free from moisture, water, and dust. • Unplug the power cord when not using the unit for long periods of time.
Page 4: Table Of Contents
Getting started Thank you for purchasing this Marantz product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading this manual, be sure to keep it for future reference. Contents Advanced instructions Information ······················································78 ···········································································137...
Page 5: Accessories
(SD) analog video content from legacy sources Warranty card (for USA) ............1 “Marantz Remote App” is application software that allows you to such as a VCR to HD and is able to output at 4K resolution (3840 Warranty card (for CANADA) ...........
Page 6: Cautions On Handling
Next, disconnect the connection cables to other system units before moving the unit. M-XPort (Marantz-eXtension Port) (vpage 19) This unit is equipped with the M-XPort, a Marantz original innovation • About care that provides outstanding expandability. You can connect the • Wipe the cabinet and control panel clean with a soft cloth.
Page 7: Basic Instructions
Basic instructions Basic instructions Here we explain the connections and basic operation methods for this unit. F Connections vpage 5 F Setup vpage 22 F Playback (Basic operation) vpage 29 F Network content vpage 46 F Selecting a listening mode (Sound Mode) vpage 72 For speaker connections, see page 81.
Page 8: Connections
Connections Important information Make connections before using this unit. NOTE To create a home theater that can play back higher quality video and audio by fully utilizing the • When video signals are being upscaled to 4K output resolution, the menu screen is only displayed capabilities of this unit and your video devices, connect this unit to each of your video devices with on a 4K display that is connected to this unit via HDMI.
Page 9 Important information Converting input video signals for HD output (Video conversion function) Make Settings as Necessary • If you do not want this unit to convert video signals automatically, This unit is equipped with three types of video input connectors (HDMI, component video and composite video) and three types of video output use the following setting item to disable this function.
Page 10: Connecting Hdmi Devices
Connecting HDMI devices You can connect up to eight HDMI-compatible devices (7-inputs/1-output) to the unit. If the device connected to this unit is equipped with an HDMI connector, it is recommended to use HDMI n Before connecting this unit to TV via HDMI connections (vpage 8) connections.
Page 11 Connecting HDMI devices Before connecting this unit to TV via HDMI connections n About ARC (Audio Return Channel) function This function plays TV audio on this unit by sending the TV audio signal to this unit via the HDMI cable. There are 2 methods to connect an HDMI-compatible TV to this unit.
Page 12 Connecting HDMI devices Connecting this unit to a TV via HDMI connections NOTE • The audio signal from the HDMI output connector (sampling frequency, number of channels, etc.) may be limited by the HDMI audio specifications of the connected device regarding permissible inputs. Cables used for connections • When connecting a TV that does not support the ARC function, an audio cable connection is required in addition to the HDMI cable.
Page 13 Connecting HDMI devices Connecting this unit to video devices via HDMI connections Video camcorder (Primary) Cables used for connections HDMI Audio and video cable (sold separately) HDMI cable Blu-ray Video Disc camcorder Set-top Game Media player (Secondary) player console player HDMI HDMI HDMI...
Page 14: Hdmi Function
Connecting HDMI devices HDMI function n About Content Type This function was added with the HDMI standard. It automatically makes settings suitable for the video- This unit supports the following HDMI functions: output type (content information). n About 3D function NOTE This unit supports input and output of 3D (3 dimensional) video signals of HDMI.
Page 15: Connecting Other Devices
Connecting other devices For highest quality video and surround playback, it is recommended to Cables used for connections Changing the source assigned to use an HDMI cable to connect this unit to TV and other video devices (vpage 7 “Connecting HDMI devices”). connectors This section describes alternate connection methods when your Video cable (sold separately)
Page 16: Connecting A Tv
Connecting other devices Connecting a TV n Audio connection The following methods are available for connecting to this unit. • This section describes how to connect when your TV does not support ARC (Audio Return Channel). a DIGITAL AUDIO OPTICAL connector For instructions on HDMI connections, see “Connecting this unit to a TV via HDMI connections”...
Page 17 Connecting other devices Connecting a set-top box (Satellite tuner/cable TV) n Audio connection The following methods are available for connecting to this unit. Use either of the methods to make This section describes how to connect when your satellite tuner or cable TV does not support HDMI a connection.
Page 18: Connecting A Dvd Player
Connecting other devices Connecting a DVD player n Audio connection The following methods are available for connecting to this unit. This section describes how to connect a DVD player that does not support HDMI connections. a AUDIO IN (DVD) connector For instructions on HDMI connections, see “Connecting HDMI devices”...
Page 19: Connecting An Ipod Or Usb Memory Device To The Usb Port
• iPod nano • iPod touch Marantz does not guarantee that all USB memory devices will operate or receive power. When using a portable USB hard disk drive (HDD) which came with an AC adapter, use that device’s supplied AC adapter. NOTE • USB memory devices will not work via a USB hub.
Page 20: Connecting A Cd Player
Connecting other devices Connecting a CD player n Audio connection The following methods are available for connecting to this unit. You can enjoy CD sound with the player connected by digital or analog cables. a AUDIO IN (CD) connector This makes an analog audio connection. CD player AUDIO AUDIO...
Page 21 Connecting other devices Connecting an FM/AM antenna Direction of broadcasting station • Connect the FM antenna supplied with the unit to enjoy listening to radio broadcasts. FM outdoor AM loop antenna • After connecting the antenna and receiving a broadcast signal (vpage 37 “Listening to FM/AM antenna (supplied)
Page 22 Connecting other devices Connecting a wireless receiver (RX101) Wireless receiver (RX101) • You can connect a wireless receiver (RX101, sold separately) to play back music on your Bluetooth device with this unit. • To do this, switch the input source to “M-XPort” (vpage 29 “Selecting the input source”).
Page 23: Connecting To A Home Network (Lan)
• The types of routers that can be used depend on the ISP. Contact your ISP or a computer shop for details. • Marantz assumes no responsibility whatsoever for any communication errors or troubles resulting from the customer’s network environment or connected devices.
Page 24: Connecting The Power Cord
Connecting the power cord After completing all the connections, insert the power plug into the power outlet. To household power outlet (AC 120 V, 60 Hz) Power cord (supplied) NOTE • Do not plug in the power cord until all connections have been completed. However, when the “Setup Assistant”...
Page 25: Setup
Setup Here, we explain “Audyssey ® Setup”, which allows you to automatically make the optimal settings for your speakers, and “Network”, which Set up speakers (Audyssey® Setup) allows you to connect this unit to a home network (LAN). This unit lets you play via your home network (LAN) music files stored on a computer and music content such as that from Internet Radio.
Page 26 Set up speakers (Audyssey® Setup) Prepare the included Setup and Set up the subwoofer Preparation measurement microphone If using a subwoofer capable of the following Mount the Setup and measurement microphone on adjustments, set up the subwoofer as shown below. a tripod or stand and place it in the main listening Connect the Setup and measurement microphone to For details, see your subwoofer’s manual.
Page 27 Set up speakers (Audyssey® Setup) Preparation (Continued) Detection & Measurement (Main) This step automatically checks the speaker configuration and speaker NOTE Select “Start” and then press size, and calculates the channel level, distance, and crossover If “Caution!” is displayed on TV screen: ENTER frequency.
Page 28 Set up speakers (Audyssey® Setup) Measurement (2nd – 6th) Calculation • In this step, you will perform measurements at multiple positions Repeat step 10, measuring positions 3 to 6. ENTER Select “Calculation” and then press (one to five additional positions) other than the main listening When measurement position...
Page 29 Set up speakers (Audyssey® Setup) Check Store Finish ENTER Unplug the Setup and measurement microphone to select the item you Select “Store” and then press Save the measurement results. from the unit’s SETUP MIC jack. want to check, and then press ENTER Set Audyssey Dynamic Volume ®...
Page 30: Error Messages
Set up speakers (Audyssey® Setup) Error messages NOTE • An error message is displayed if Audyssey ® Setup could not be completed due to speaker placement, the measurement environment, etc. If an error message is displayed, check the relevant items and perform the necessary measures.
Page 31: Making The Network Settings (Network)
Set up speakers (Audyssey® Setup) Making the network settings Check Results (Network) This function enables you to check the measurement results and equalizer characteristics after Audyssey ® This unit can be connected to a home network (LAN) to listen to Internet Radio or play back music files and Setup.
Page 32: Playback (Basic Operation)
Playback (Basic operation) Important information Setup (vpage 22) Before starting playback, make the connections between the different Selecting the input source devices and the settings on the unit. n Turning the power on (vpage 29) NOTE Press the input source select button n Selecting the input source (vpage 29) CBL/SAT Blu-ray...
Page 33: Playing A Blu-Ray Disc Player/Dvd Player
Important information Playing a CD player Playing a Blu-ray Disc player/DVD Adjusting the master volume player The following describes the procedure for playing CD player. VOLUME df to adjust the Prepare for playback. The following describes the procedure for playing Blu-ray Disc player/ volume.
Page 34: Playing An Ipod
Playing an iPod You can use the USB cable provided with the iPod to connect the iPod Listening to music on an iPod Operations available through the OPTION button with the unit’s USB port and enjoy music stored on the iPod. For information on the iPod models that can be played back with this OPTION Press the...
Page 35 • Depending on the type of iPod and the software version, some Playback starts. functions may not operate. • Note that Marantz will accept no responsibility whatsoever for any problems arising with the data on an iPod when using this unit in conjunction with the iPod.
Page 36 Playing an iPod n Performing repeat playback (Repeat) n Performing random playback (Random) During random playback, each time playback of a track is completed, OPTION OPTION Press with “iPod Browse Mode” set to Press with “iPod Browse Mode” set to another track is randomly selected for playback from tracks in the “On-Screen”.
Page 37: Playing A Usb Memory Device
Playing a USB memory device Playing back music or viewing still picture (JPEG) files stored on a USB memory device. Important information • Only USB memory devices conforming to mass storage class and MTP (Media Transfer Protocol) GCompatible formatsH standards can be played on this unit. Sampling frequency Bit rate Extension...
Page 38 NOTE n Displaying your desired video on the monitor during • Note that Marantz will accept no responsibility whatsoever for any audio playback (Video Select) (vpage 68) problems arising with the data on a USB memory device when using to select the file, then this unit in conjunction with the USB memory device.
Page 39 Playing a USB memory device n USB memory device operation buttons Operation buttons Function CH/PAGE df Page search Display of information such as the INFO source name, volume, and sound mode name etc. Text Search / Repeat playback / Random playback / OPTION Slideshow Interval / Video Select /...
Page 40: Listening To Fm/Am Broadcasts
Listening to FM/AM broadcasts For antenna connections, see “Connecting an FM/AM antenna” Listening to FM/AM broadcasts ENTER (vpage 18). to select “FM” or “AM”, then press TUNER Press to switch the input GTV ScreenH How to tune in source to “TUNER”. TUNER GTV ScreenH The modes for receiving FM broadcasts consists of “Auto”...
Page 41 Listening to FM/AM broadcasts n Changing the screen display duration Operations available through the OPTION button Make this setting at “Now Playing” OPTION Press the button to display a menu of functions that can be (vpage 118) in the menu. The default used on the TV screen.
Page 42 Listening to FM/AM broadcasts n Tuning in by entering the radio frequency to select a number and press (Direct Tune) The screen that lets you enter the frequency is displayed. You can enter the receiving frequency directly to tune in. GTV ScreenH TUNER Press...
Page 43 Listening to FM/AM broadcasts n Presetting the current broadcast station Channel Default settings to select the channel you want to preset, then (Preset Memory) 92.10 / 92.30 / 92.50 / 92.70 / 93.10 / 93.50 / 93.70 / ENTER press 1 –...
Page 44 Listening to FM/AM broadcasts n Changing the tuning mode (Tune Mode) ENTER to select tuning mode, then press You can change the mode for tuning into FM broadcasts. If you cannot tune in automatically with “Auto” mode, then change the GTV ScreenH mode to “Manual”...
Page 45 Listening to FM/AM broadcasts n Tuning in to radio stations and presetting them ENTER Press automatically (Auto Preset Memory) The unit starts to tune in to radio stations automatically and Up to 56 stations can be preset. preset them. If “Auto Preset Memory” is performed after performing “Preset GTV ScreenH Memory”, the “Preset Memory”...
Page 46 Listening to FM/AM broadcasts n Specify a name for the preset broadcast station ENTER to select the group of the broadcast station to select a name label, then press (Preset Name) ENTER you want to name then press The screen that lets you edit the preset name is displayed. You can set the name to the preset broadcast station or change it.
Page 47 Listening to FM/AM broadcasts n Skipping preset broadcast stations GTo set the stations you want to skip by stationsH GTo set the stations you want to skip by groupsH (Preset Skip) q Use to select the group of broadcast q Use to select the group of broadcast You can set in advance, the stations you do not want to be stations you want to skip.
Page 48 Listening to FM/AM broadcasts Cancelling preset skip n Tuner operation buttons Operation buttons Function While the Preset Skip screen is displayed, use FAVORITE Call up favorite stations to select a group containing a broadcast station to STATION 1 – 3 cancel the skip for.
Page 49: Network Content
Network content Listening to Internet Radio Internet Radio refers to radio broadcasts distributed over the Internet. Listening to Internet Radio to select the item you want to play, then Internet Radio stations from around the world can be received. ENTER press Important information Prepare for playback.
Page 50 Listening to Internet Radio n Adjusting the sound quality (M-DAX) Operations available through the OPTION button n Playing the last played Internet Radio station Make this setting at “M-DAX” (vpage 111) in the menu. This unit memorizes the last played Internet Radio station. If you OPTION Press the button to display a menu of functions that can be...
Page 51 Listening to Internet Radio n Using vTuner to add Internet Radio stations to n Internet Radio operation buttons Select the radio station of your choice from the list, favorites and then click the Add to Favorites icon. Operation buttons Function There are many Internet Radio stations in the world, and this unit The screen that lets you create a favorite group is displayed.
Page 52: Playing Back Files Stored On A Pc And Nas
Playing back files stored on a PC and NAS This unit can play back music files and playlists (m3u, wpl) stored on a PC and on Network Attached Storage (NAS) that supports DLNA. Important information • The network audio playback function of this unit connects to the server using technologies shown below. GSpecifications of supported filesH • Windows Media Player Network Sharing Service Sampling frequency...
Page 53 “Allow”. select “Choose media streaming options”. Click “OK” to finish. Select “Allowed” in the drop-down list for “NR1604”. Sharing media stored in NAS Select “Allowed” in the drop-down list for “Media Change settings on the NAS to allow this unit and other devices (PCs programs on this PC and remote connections...”.
Page 54 Playing back files stored on a PC and NAS Playing back files stored on a PC and NAS n Adjusting the sound quality (M-DAX) Make this setting at “M-DAX” (vpage 111) in the menu. • When a WMA (Windows Media Audio), MP3 or MPEG-4 AAC file Use this procedure to play music files, image files or playlists.
Page 55 Playing back files stored on a PC and NAS Operations available through the OPTION button n Media Server operation buttons OPTION Press the button to display a menu of functions that can be Operation buttons Function used on the TV screen. Select the function you want to use from this CH/PAGE df Page search menu.
Page 56: Using Online Services
Genome Project. Introduce your Marantz to a whole new world of music. With Spotify, you can enjoy instant access to To listen to Pandora you will need a free Pandora account. If you do not have a Pandora account, you millions of songs.
Page 57: Viewing Photographs On The Flickr Site
Using online services Viewing photographs on the Flickr site n Going back to the previous screen In “Contact”, add the screen name (user name you BACK Press want to view) you want to add. You can view photographs shared by particular users, or all of the photographs shared on Flickr.
Page 58 Using online services n Viewing all photographs on Flickr n Flickr operation buttons Operation buttons Function ENTER to select “All Content”, then press CH/PAGE df Page search Display of information such as the INFO source name, volume, and sound mode Flickr [1/2] name...
Page 59: Listening To Pandora
When “Cancel Input?” is displayed, Media Server I am new to Pandora ENTER select “Yes”, then press Please go to Spotify http://www.pandora.com/marantz and follow the instructions there to create a new account. v See overleaf Your activation code is : zzzzzz Cancel...
Page 60 Using online services Operations available through the OPTION button n Creating a new station to select “Search by Artist” or “Search by You can create up to 100 radio stations. OPTION Press the button to display a menu of functions that can be ENTER Track”, then press used on the TV screen.
Page 61 Using online services NOTE n Listening to an existing station n Giving Feedback and Managing Stations • You can Skip up to 6 Tracks that are being played back within 1 hour. You can personalize your stations by providing feedback. and select the radio station • You can create up to 100 Stations (radio stations).
Page 62 Using online services n Pandora operation buttons Operation buttons Function CH/PAGE df Page search Display of information such as the INFO source name, volume, and sound mode name Video Select / OPTION Picture Mode / All Zone Stereo Cursor operation / uio p Skips the current track, subject to skip limit (i)
Page 63: Listening To Siriusxm Internet Radio
Using online services Listening to SiriusXM Internet Radio n Going back to the previous screen ENTER Select “Sign in”, then press BACK Press Over 120 channels of the SiriusXM programming you love, including commercial-free music plus sports, talk, news and entertainment. Operations available through the OPTION button Listen anywhere on your computer or smartphone.
Page 64 Using online services n Sign out n SiriusXM operation buttons Disassociate this unit from your SiriusXM account. Operation buttons Function CH/PAGE df Page search ENTER to select “Sign Out”, then press Display of information such as the INFO source name, volume, and sound mode name When the popup menu appears, use to select...
Page 65: Listening To Spotify
If you have a Spotify account, then press ENTER “Log In”, then press Introduce your Marantz to a whole new world of music. With Spotify, If the username and password match, the top menu for Spotify you can enjoy instant access to millions of songs.
Page 66 Using online services Operations available through the OPTION button n Spotify operation buttons Press while a track is playing. OPTION Press the button to display a menu of functions that can be The Spotify menu screen is displayed. Operation buttons Function used on the TV screen.
Page 67: Convenient Functions
Convenient functions Here, we explain how to use convenient functions for NETWORK Searching content with keywords Performing repeat playback (Repeat) sources and USB sources. The source names under the titles of each function’s description are sources that allow use of these functions. (Text Search) Media Server Spotify...
Page 68 Convenient functions Performing random playback (Random) During random playback, each time playback of a track is completed, Media Server Spotify another track is randomly selected for playback from tracks in the folder. Therefore, it's possible that you may hear a track played back OPTION While content is playing, press more than once during random playback.
Page 69 Convenient functions Favorites function Playing back content added in “Save to Favorites” FAVORITE STATION Contents that can be added to the button differ There are two ways to add content to favorites: NETWORK Press depending on the input source. q Add to favorites from the Option menu FAVORITE STATION w Add to the button...
Page 70 Convenient functions n Deleting content added to favorites Playing back music and a favorite picture Playing back still images in sequential (Remove from Favorites) at the same time (Slideshow) order (Slideshow Interval) NETWORK Press You can play back still image (JPEG) files stored on a USB memory Internet Radio Media Server device or Media Server and pictures on Flickr website as a slide show.
Page 71 Convenient functions Displaying your desired video on the Adjusting the picture quality for your to select the Video Select mode. monitor during audio playback (Video viewing environment (Picture Mode) • Each time is pressed, the setting is changed as shown below. Select) CBL/SAT Blu-ray...
Page 72 Convenient functions n Stopping the All Zone Stereo function All Zone Stereo function to select picture mode. During playback in All Zone You can play back music in multi-zones (ZONE2) simultaneously that OPTION is played back in MAIN ZONE. Stereo, press Internet Radio It is useful when you want to enjoy the same music at the same time The option menu screen is displayed.
Page 73: Airplay Function
My Computer displayed the window and select this unit from the list. • For details, see your device’s manual. Marantz NR1604 Startup iPhone, iPod touch, or iPad music or iPod app. v See overleaf is displayed on the iPhone, iPod touch or iPad screen.
Page 74 AirPlay function n Perform iTunes playback operations with the remote control unit of this unit • is displayed on the menu screen while With this unit’s remote control unit, you can perform iTunes song AirPlay is being operated. play, pause, and auto search (cue) operations. • Source input will...
Page 75: Selecting A Listening Mode (Sound Mode)
Selecting a listening mode (Sound Mode) This unit allows you to enjoy various kinds of surround and stereo Selecting a listening mode playback modes. Multi-channel audio formats are provided on popular movie and music Play the selected device (vpage 30 – 62). Direct playback disc formats such as Blu-ray and DVD, as well as being supported by digital broadcasting, and even by streaming movies and music from...
Page 76: Pure Direct Playback
Selecting a listening mode Pure Direct playback Auto surround playback This mode is for playback with higher sound quality than in “DIRECT” This mode detects the type of input digital signal, and automatically mode, by turning off the front panel display panel, which can eliminate selects the corresponding mode for playback.
Page 77 Selecting a listening mode n Listening mode MOVIE MUSIC GAME PURE • The following listening modes can be selected using the , and buttons. • Adjust the sound field effect with the menu “Surround Parameter” (vpage 109) to enjoy surround sound the way you like it. z1 2-channel also includes analog input.
Page 78 Selecting a listening mode z1 2-channel also includes analog input. Views on the TV screen or display Operation Input signal Listening mode z2 When AUTO mode is selected, the sound mode that is compatible button with the input signal is used for playback. STEREO z3 This mode plays back 2-channel sources in 5.1 or 7.1-channel AUTO...
Page 79 Selecting a listening mode n Description of listening mode types Dolby listening mode DTS listening mode Listening mode type Description Listening mode type Description DOLBY PLgx This mode can be selected when the Dolby Pro Logic gx decoder is used to DTS NEO:6 This mode can be selected when a DTS NEO:6 decoder is used to play back play back 2-channel sources in 6.1/7.1-channel surround sound including the...
Page 80 Selecting a listening mode Original listening mode Direct listening mode Listening mode type Description Listening mode type Description MULTI CH STEREO This mode is for enjoying stereo sound from all speakers. DIRECT This mode provides a direct input-to-output path with minimal audio processing, Stereo audio (2 channel) sources are played back via the front (L/R) speakers, bypassing any unnecessary stages for purest sound.
Page 81: Advanced Instructions
Advanced instructions Advanced instructions Here we explain functions and operations in more detail so that you can maximize your enjoyment with this unit. F Installation/connection/setup of speakers (Advanced) vpage 79 F Connections (Advanced connection) vpage 93 F Playback (Advanced operation) vpage 95 F Playback in ZONE2 (Separate room) vpage 101 F How to make detailed settings vpage 103...
Page 82: Installation/Connection/Setup Of Speakers (Advanced)
Installation/connection/setup of speakers (Advanced) Speaker installation Procedure for speaker settings • Determine the speaker system depending on the number of speakers When 7.1-channel speakers are installed Speaker installation you are using and install each speaker and subwoofer in the room. Here, we explain how to install the speakers using a typical example. using surround back speakers • The speaker impedance should be from 6 to 16 Ω/ohms.
Page 83 Speaker installation When 7.1-channel speakers are installed When 6.1-channel speakers are installed When 5.1-channel speakers are installed using front height speakers Listening position Listening position Listening position z1 22˚ – 30˚ z2 120˚ z1 22˚ – 30˚ z2 22˚ – 45˚ z3 90˚...
Page 84: Speaker Connection
Speaker connection Here we connect the speakers in the room to this unit. Connecting the speaker cables This section explains how to connect them using typical examples. Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to this unit, and be sure to connect the channels and polarities correctly.
Page 85: Connecting The Subwoofer
Speaker connection Connecting the subwoofer n About the speaker cable label (supplied) for channel identification Cables used for connections The channel display section for speaker terminals on the rear panel is color-coded for each channel to Use a subwoofer cable to connect the subwoofer. be identifiable.
Page 86 Speaker connection Connecting 7.1-channel speakers using surround back speakers The illustration on the right shows a connection example for performing 7.1-channel playback using the surround back speakers. To perform 7.1-channel playback using the surround back speakers, set “Assign Mode” to “Surround Back”...
Page 87 Speaker connection Connecting 7.1-channel speakers using front height speakers The illustration on the right shows a connection example for performing 7.1-channel playback using the front height speakers. To perform 7.1-channel playback using the front height speaker, set “Assign Mode” to “Front Height” in steps 3 to 5 for “Set up “Amp Assign””...
Page 88 Speaker connection Connecting 6.1-channel speakers using one surround back speaker If using only one surround back speaker, connect to the “L” side of the SURROUND BACK terminal. For speaker settings in this case, see “When 6.1-channel speakers are installed” (vpage 80). To perform 6.1-channel playback using the surround back speaker, set “Assign Mode”...
Page 89 Speaker connection Connecting 5.1-channel speakers To perform 5.1-channel playback, set “Assign Mode” to “Surround Back” in steps 3 to 5 for “Set up “Amp Assign”” (vpage 91). NOTE • For speaker cable connections, see page 82. • For speaker impedance, see page 81.
Page 90 Speaker connection Connecting front A/B speakers You can connect a second set of speakers to this unit and use them for playback. In this case, set “Assign Mode” to “Front B” in steps 3 to 5 for “Set up “Amp Assign”” (vpage 91). For multi-channel playback, connect center, surround, surround back, and front speakers and a subwoofer.
Page 91 Speaker connection Connecting 2.1-channel speakers NOTE • For speaker cable connections, see page 82. • For speaker impedance, see page 81.
Page 92 Speaker connection Connecting front speakers with a bi-amp connection Some audiophile loudspeakers can be connected to an amplifier with two separate amp-to-speaker connections per each speaker. One amplifier channel’s output is hooked up to the speaker’s bass driver (woofer), while the other amplifier drives the upper range transducers (tweeter, or in some cases midrange and tweeter).
Page 93 Speaker connection Connecting a front speaker that uses a power amplifier This unit supports connection of a front speaker that uses an external power amplifier to increase its output. Connect a separately sold power amplifier to the PRE OUT (FL/FR) connector of this unit. NOTE • For speaker cable connections, see page 82.
Page 94: Set Up Speakers
Set up speakers around items indicate the settings. This section describes detailed settings for Audyssey ® Setup. First install and connect the speakers to this unit. Before Audyssey ® Setup measurement, the settings shown below can be made. • Changing the amplifier assignment (Amp Assign) The signal output from the SURROUND BACK speaker terminals of this unit can be switched to match your speaker environment (vpage 91 “Set up “Amp Assign””).
Page 95 Set up speakers to select the to select a front speaker, and then press Set up “Channel Select” ENTER configuration of the connected to select “Channel Select”, and then press speakers, and then press Select this to use front speaker A. ENTER ENTER Select this to use front speaker B.
Page 96: Connections (Advanced Connection)
Remotely control a Marantz Blu-ray player by the Marantz Remote App Marantz Blu-ray disc player of newer generation also can be controlled via a network receiver unit using the n Performing operations by RC on this unit without visual contact Marantz Remote App.
Page 97: Connecting An External Control Device
Connecting an external control device DC OUT jack When a device with DC IN jack is connected, the connected device’s power on/standby can be controlled through linked operation to this unit. The DC OUT jack outputs a maximum 12 V/150 mA electrical signal. 12 V/150 mA trigger-compatible device NOTE • Use the monaural mini-plug cable for connecting DC OUT jacks.
Page 98: Playback (Advanced Operation)
Playback (Advanced operation) HDMI control function Setup (vpage 22) A recent addition to the HDMI standard is CEC, which allows control n Setting procedure signals from one device to communicate with another device via the Playback (Basic operation) (vpage 29) HDMI cable connection. Not all HDMI-equipped devices allow . Set the HDMI output connector corresponding with Selecting a listening mode (Sound Mode) n Operations possible by HDMI control...
Page 99: Sleep Timer Function
HDMI control function Sleep timer function • You can have the power automatically switched to standby once a set time has elapsed. This is convenient for viewing and listening If the HDMI control function does not operate properly, check the • The sleep timer setting is canceled if this unit’s power is set to while going to sleep.
Page 100: Web Control Function
For example, if the IP address of this unit is “192.168.0.2”, • This unit and the PC need to be connected to the network properly Marantz NR1604 enter “http://192.168.0.2”. (vpage 20 “Connecting to a home network (LAN)”) in order to...
Page 101 Web control function GExample 2H Setup menu screen Video Video/HDMI Setup Picture Adjust Auto Lip Sync HDMI Setup HDMI Audio Out Output Settings HDMI Pass Through On Screen Display HDMI Control Last Pass Through Source TV Format Blu-ray CBL/SAT GAME AUX2 MEDIA PLAYER Not available...
Page 102: Dual Backup Memory Function
Dual backup memory function Panel lock function The unit stores settings information in nonvolatile memory even when To prevent accidental operation of this unit, you can disable operation n Canceling the Panel lock function the main power supply is turned off. Using the Dual Backup Memory of the buttons on the front panel.
Page 103: Remote Lock Function
Remote lock function Various memory functions • When not connecting an IR receiver, disable the Remote lock n Enabling the remote sensor function Personal memory plus function function. When the function is enabled, you can not perform operations with the remote control unit. When the main unit is in standby mode, press This function sets the settings (input mode, sound mode, HDMI • By default, this function is disabled.
Page 104: Playback In Zone2 (Separate Room)
Playback in ZONE2 (Separate room) • You can operate this unit so as to enjoy audio in a room (ZONE2) Playback other than the MAIN ZONE (room where the unit is located). • You can simultaneously play back the same source in both the MAIN ZONE2 Press to switch the zone...
Page 105: Sleep Timer Function
Sleep timer function • This is convenient for viewing and listening while going to sleep in ZONE2. • The sleep timer function can be set by zone. ZONE2 Press to switch the zone mode. ZONE2 lights. SLEEP Press and display the time you want to set.
Page 106: How To Make Detailed Settings
Used to check the network connection. Video On Screen Display Select the on-screen display user interface Maintenance Mode Use when receiving maintenance from a Marantz preferences. service engineer or custom installer. TV Format Set the video output signal format for the TV you are using.
Page 107 Show information about receiver settings, input signals, etc. Usage Data Selects whether or not to send anonymous usage data to Marantz. Firmware Set whether or not to check for firmware update, update the firmware, and display update and upgrade notifications.
Page 108: Examples Of Menu Screen Displays
Examples of menu screen displays Typical examples are described below. GExample 2H GExample 1H Audyssey ® Setup screen (with illustration) Menu selection screen (Top menu) Audyssey Setup Setup Menu Audio Your AV receiver can automatically measure the acoustics of your room then optimize your speakers using the included Video microphone.
Page 109: Examples Of Menu And Front Display
Examples of menu and front display Below we describe typical examples of displays on the TV screen and on the set’s display window. Menu display Front display Description Top menu display q Press SETUP to display the menu screen. Setup Menu w TV screen: Displays the selected line.
Page 110: Inputting Characters
Inputting characters On this unit, you can change the name displayed on the following Keyboard screen n Input method screens to the names that you prefer. • Text Search (vpage 64) Display the screen for inputting Select a character on the TV screen to input characters. • Preset Name (vpage 43) characters (vpage ...
Page 111: Audio
Audio Make audio-related settings. Items that can be set with the “Audio” procedure Menu operation Dialog Level (vpage 109) MAIN Press to switch the zone mode. Subwoofer Level (vpage 109) MAIN lights. SETUP Press Surround Parameter (vpage 109) The menu is displayed on the TV screen. Tone (vpage 111) to select the menu to be set or operated.
Page 112: Dialog Level
Audio Dialog Level Surround Parameter Default settings are underlined. Default settings are underlined. Sets the output level to clarify the dialogue output from the center channel. You can adjust the surround audio sound field effects to match your preferences. The items (parameters) that can be adjusted depend on the signal being input and the currently set Setting items Setting details sound mode.
Page 113 Audio Setting items Setting details Setting items Setting details Low Frequency Effects –10dB – 0dB Height Gain Low : Reduce the front height channel volume. Normal : Front height channel sound is output with standard sound Adjust the low-frequency Control the front height For proper playback of the different sources, we recommend setting effects level (LFE).
Page 114 Audio Tone M-DAX Default settings are underlined. Adjust the tonal quality of the sound. Compressed audio formats such as MP3, WMA (Windows Media Audio) and MPEG-4 AAC reduce the amount of data by eliminating signal components that are hard for the human ear to hear. The “M-DAX” Setting items Setting details function generates the signals eliminated upon compression, restoring the sound to conditions near those...
Page 115: Audio Delay
Audio Audio Delay Audyssey Default settings are underlined. Default settings are underlined. Set Audyssey MultEQ ® , Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . These can be selected While viewing video, manually adjust the time to delay audio output so that the video and audio are after Audyssey ®...
Page 116 Audio Graphic EQ Setting items Setting details Default settings are underlined. Dynamic EQ On : Use Dynamic EQ. Use the 9 band graphic equalizer to adjust the tone of each speaker. Off : Do not use Dynamic EQ. Solves the problem of “Graphic EQ”...
Page 117: Video
Video Make video-related settings. Items that can be set with the “Video” procedure Menu operation Picture Adjust (vpage 115) MAIN Press to switch the zone mode. MAIN lights. HDMI Setup (vpage 115) SETUP Press The menu is displayed on the TV screen. Output Settings (vpage 116) to select the menu to be set or operated.
Page 118: Picture Adjust
Video Picture Adjust Setting items Setting details Default settings are underlined. Noise Reduction Low / Medium / High / Off Picture quality can be adjusted. Reduce overall video noise. “Noise Reduction” can be set when “Picture Mode” is set to We recommend leaving the settings unchanged from the default settings.
Page 119 Video Output Settings Setting items Setting details Default settings are underlined. HDMI Control On : Use HDMI control function. Makes screen-related settings. Off : Do not use HDMI control function. You can link operations with z “CBL/SAT”, “DVD”, “Blu-ray”, “GAME”, “AUX1”, “AUX2”, “MEDIA PLAYER”, “CD” or “TV AUDIO” devices connected to HDMI can be set when “HDMI”, “COMP”...
Page 120 Video Setting items Setting details Setting items Setting details i/p Scaler Progressive Mode Auto : The video signal is automatically detected and the appropriate n When the input source is set other than to “iPod/USB” and “NETWORK” Convert the input source Analog : Use i/p (interlace-to-progressive) scaler function for analog Set an appropriate mode is set.
Page 121: On Screen Display
Video On Screen Display TV Format Default settings are underlined. Default settings are underlined. Select the on-screen display user interface preferences. Set the video signal format to be output for the TV you are using. Setting items Setting details Setting items Setting details Volume Bottom : Display at the bottom.
Page 122: Inputs
Inputs Perform settings related to input source playback. Items that can be set with the “Inputs” procedure • You do not have to change the settings to use the unit. Make settings when needed. Menu operation Input Assign (vpage 120) MAIN Press to switch the zone mode.
Page 123: Input Assign
Inputs Input Assign Setting items Setting details HDMI 1 / 2 / 3 / 4 / 5 / 6 / FRONT : Assign an HDMI input connector to the This unit has certain input sources such as “CBL/SAT” assigned to audio and video connectors by default. Set this to change the HDMI selected input source.
Page 124 Inputs Setting items Setting details Setting items Setting details DIGITAL COAX (Coaxial) / OPT (Optical) : Assign a digital input connector to the COMP 1 / 2 : Assign the component video input connector to the selected input Set this to change the digital selected input source.
Page 125: Source Rename
Inputs Source Rename Source Level Default settings are underlined. Change the display name of the selected input source. • This function corrects the playback level of the selected input source’s audio input. This is convenient when the input source name of your device and the input source name of this unit are • Make this setting if there are differences in the input volume levels between the different sources.
Page 126: Speakers
Speakers Set when changing Audyssey ® Setup settings. Items that can be set with the “Speakers” procedure • If you change the speaker settings after performing Audyssey ® Setup, it will not be possible to set Audyssey MultEQ ® , Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® (vpage 112, 113).
Page 127 Speakers Manual Setup Setting items Setting details Default settings are underlined. Speaker Config. Surround : Set the presence and size of the surround speakers. Perform when setting the speakers manually or when changing settings made in Audyssey ® Setup. (Continued) • Large : Use a large speaker that can adequately play back very low bass • If you change the speaker settings after performing Audyssey ®...
Page 128 Speakers Setting items Setting details Setting items Setting details Distances Unit : Set the unit of distance. Levels Test Tone Start : Output test tone. • Feet / Meters • Front L / F. Height L / Center / F. Height R / Front R / Surround R / Set distance from listening Set the volume of the test position to speakers.
Page 129 Speakers Setting items Setting details Setting items Setting details Crossovers Speaker Selection : Selects how to set the crossover frequency. See the Bass Subwoofer Mode : Select low range signals to be reproduced by Set the maximum frequency speaker manual for information concerning speaker crossover frequency. Set subwoofer and LFE subwoofer.
Page 130: Network
Network To use this unit by connecting it to a home network (LAN), you must configure network settings. Items that can be set with the “Network” procedure If you set up your home network (LAN) via DHCP, set “DHCP” to “On” (use the default setting). This allows this unit to use your home network (LAN).
Page 131: Friendly Name
Setting details Friendly Name / DHCP On or Off / IP Address / MAC Address Edit Name • The default Friendly Name on first use is “Marantz NR1604”. MAC Address is required to make a vTuner account. Edits Friendly Name. • Up to 63 characters can be input.
Page 132 Network Settings Setting details ENTER u Use to select “Proxy” and press Make settings for wired LAN. • Proxy : Make this setting when connecting to the Internet via a proxy server. Only set “Settings” when connecting to a network without a DHCP function. Make the proxy settings only when you connect to the Internet via a proxy server that is on your internal network or provided by your provider, etc.
Page 133: Maintenance Mode
(WAN). Maintenance Mode Use when receiving maintenance from a Marantz service engineer or custom installer. Ordinarily, this mode isn’t suitable for use by the end user, only by a trained service technician or custom installation professional.
Page 134: General
General Make various other settings. Items that can be set with the “General” procedure Menu operation Language (vpage 132) MAIN Press to switch the zone mode. MAIN lights. ZONE2 Setup (vpage 132) SETUP Press Zone Rename (vpage 132) The menu is displayed on the TV screen. to select the menu to be set or operated.
Page 135: Zone Rename
General Language Setting items Setting details Default settings are underlined. Power On Volume Last : Use the memorized setting from the last session. Set the language for display on the menu screen. Mute : Always mute when power is turned on. Define the volume setting that is active when the 1 –...
Page 136: Trigger Out
General Trigger Out Front Display Default settings are underlined. Selects when to activate trigger out. Adjust the display brightness of this unit. For details about how to connect the DC OUT jacks, see “DC OUT jack” (vpage 94). Setting items Setting details Setting details Display On : Display is always on.
Page 137 Firmware Version : Displays information for the current firmware. Notifications Notification Alerts Selects notification message • On : Displays notification messages from Marantz in the popup menu. preferences. • Off : Does not display notification messages from Marantz in the popup menu.
Page 138: Usage Data
Display a notification ENTER • When you press during display of the No : Do not provide Marantz with information about how you use this unit via the network. message on this unit’s notification message, the “Check for Update” menu screen when screen is displayed (Refer to page 135...
Page 139 Add New Feature Upgrade Package : Display the items to be upgraded. • Information regarding the “Update” function and “Add New Feature” will be announced on the Marantz Upgrade Status : Display a list of the additional functions provided by the Display new features that web site each time related plans are defined.
Page 140: Information
Information Information Here we list other information related to this unit. Please refer to this information as needed. F Part names and functions vpage 138 F Other information vpage 143 F Troubleshooting vpage 153 F Specifications vpage 158 F Index vpage 159...
Page 141: Part Names And Functions
Part names and functions Front panel For buttons not explained here, see the page indicated in parentheses ( ). y u i Q1 Q2 Power indicator ······································································· (29) Headphones jack (PHONES) DISPLAY button ····································································· (133) GPower indicator statusH When the headphones are plugged into this jack, audio will no STATUS button ·············································...
Page 142: Display
Display Information display Sleep timer indicator Decoder indicator The input source name, sound mode, setting values and other This lights when the sleep mode is selected (vpage 96). These light when Dolby or DTS signals are input or when the Dolby information are displayed here.
Page 143: Rear Panel
Rear panel See the page indicated in parentheses ( ). FM/AM antenna terminals (ANTENNA) ································ (18) Digital audio connectors (DIGITAL AUDIO) ···················· (13, 14) NOTE Analog audio connectors (AUDIO) ···························· (14, 15, 17) Network connector (NETWORK) ··········································· (20) Do not touch the inner pins of the connectors on the rear panel. Electrostatic discharge may cause permanent damage to the unit.
Page 144: Remote Control Unit
Remote control unit For buttons not explained here, see the page indicated in parentheses ( ). ZONE SELECT buttons (MAIN, ZONE2) ··············· (23, 69, 91, 101, 142) Input source select buttons ··············· (29, 101) Channel/page search buttons (CH/PAGE df) ··············· (33, 36, 40, 45, 48, 52, 55, 59, 61, 63) MUTE button (:) ····························· (30, 101) Information button (INFO) ·······················...
Page 145: Inserting The Batteries
Remote control unit Inserting the batteries Operating range of the remote control unit Specifying the zone used with the remote control unit Point the remote control unit at the remote sensor when operating it. q Remove the rear lid in the w Load the two batteries properly direction of the arrow and as indicated by the marks in the...
Page 146: Other Information
Other information Trademark information n Trademark information (vpage 143) n Surround (vpage 144) n Relationship between video signals and monitor output (vpage 148) n Explanation of terms (vpage 150) Manufactured under license from Audyssey Laboratories™. U.S. and foreign patents pending. Audyssey MultEQ ® , Audyssey Dynamic “Made for iPod”...
Page 147: Surround
Surround This unit is equipped with a sophisticated digital signal processing circuit that lets you play your favorite movie and music sources and listen to them with a wide range of surround sound mode choices. Sound modes and surround parameters This table shows the speakers that can be used in each sound mode and the surround parameters adjustable in each sound mode.
Page 148 Surround Surround Parameter (vpage 109) Audyssey (vpage 112) NEO:6 Music mode PRO LOGIC g/gx Music mode only Tone M-DAX only Subwoofer Sound Mode (vpage 72) (vpage 109) MultEQ ® Dynamic EQ Dynamic Volume (vpage 111) (vpage 111) Panorama Dimension Center Width Center Image (vpage 110) (vpage 110) (vpage 110) (vpage 110) (vpage 112) (vpage 113)
Page 149 Surround n Types of input signals, and corresponding sound modes This table shows the input signal that can be played in each sound mode. Check the audio signal of the input source then select the sound mode. Symbols in the table F This indicates the default sound mode.
Page 150 Surround Input signal types and formats DTS-HD DOLBY DOLBY DIGITAL DOLBY Sound Mode (vpage 72) NOTE DTS-HD High DTS ES DTS ES DOLBY DOLBY DOLBY ANALOG DTS-HD DOLBY DOLBY DIGITAL EX (Multi- Resolution DSCRT MTRX DTS 96/24 DIGITAL EX DIGITAL DIGITAL (2-channel) Master Audio EXPRESS...
Page 151: Relationship Between Video Signals And Monitor Output
Relationship between video signals and monitor output MAIN ZONE MONITOR OUT Input connector Output connector Menu displayed Video Conversion HDMI COMPONENT VIDEO HDMI COMPONENT VIDEO HDMI COMPONENT VIDEO Only the menu is displayed S <VIDEO> S <VIDEO> S (VIDEO) A (VIDEO) S <COMPONENT>...
Page 152 Relationship between video signals and monitor output Video signal resolution conversion table When “Video Conversion” (vpage 116) is set to “On”, “i/p Scaler” (vpage 117) is set to “Analog”, “Analog & HDMI” or “HDMI” are set, the resolution of the input video signal can be converted to a different resolution for output (vpage 6 “Converting input video signals for HD output (Video conversion function)”).
Page 153: Explanation Of Terms
Explanation of terms Auto Lip Sync Dolby Digital Plus Dolby Pro Logic gz, with front height channels is If you connect the unit to a TV that supports the Dolby Digital Plus is an improved Dolby Digital signal also an ideal alternative for households that cannot A2DP Auto Lip Sync function, it can automatically correct format that is compatible with up to 7.1 channels...
Page 154 Explanation of terms DTS Express DTS Express is an audio format supporting low bit FLAC HDCP Pairing rates (max. 5.1 channels, 24 to 256 kbps). FLAC stands for Free lossless Audio Codec, and is a When transmitting digital signals between devices, Pairing is an operation required for settings to DTS-HD lossless free audio file format.
Page 155 Explanation of terms Windows Media DRM x.v.Color This is a copyright protection technology developed This function lets HDTVs display colors more by Microsoft. accurately. enables display with natural, Content providers are using the digital rights vivid colors. “x.v.Color” is trademark of Sony management technology for Windows Media Corporation.
Page 156: Troubleshooting
– 2. Is the set being operated as described in the owner’s manual? power, the power please contact the Marantz service adviser. 3. Are the other devices operating properly? indicator is blinking If this unit does not operate properly, check the items listed in the table below. Should the problem persist, red in intervals of there may be a malfunction.
Page 157 GVideoH Symptom Cause/Solution Page Symptom Cause/Solution Page No sound is • Check if “Assign Mode” is set appropriately in order to output No picture appears. • Check the connection between the video output terminal of this produced from front audio from the front height speakers. unit and the input terminal of the TV.
Page 158 – settings so that the unit can access the folders on your computer. This is not a malfunction. Marantz does not guarantee that all USB Music stored on • If you use a NAS in conformity with the DLNA standard, enable –...
Page 159 Pandora. (“Email Pandora has been properly entered. Re-enter the “Password”. function. latest version. address” or (Password is not displayed.) “Password” is http://www.pandora.com/marantz GM-XPortH displayed.) Symptom Cause/Solution Page Audio is not output • Check that the Bluetooth device and Wireless receiver (RX101) 19, 150, 151...
Page 160: Resetting The Microprocessor
GRemote control unitH Resetting the microprocessor Symptom Cause/Solution Page Perform this procedure if the display is abnormal or if operations cannot be performed. The set cannot be • Batteries are worn out. Replace with new batteries. Note that when the microprocessor is reset, all the settings are reset to their default values. operated with the • Operate the remote control unit within a distance of about remote control unit.
Page 161: Specifications
Specifications n Audio section n Tuner section [FM] [AM] (Note: μV at 75 Ω/ohms, 0 dBf = 1 x 10 –15 W) • Power amplifier Rated output: Front: Receiving Range: 87.5 MHz – 107.9 MHz 520 kHz – 1710 kHz 50 W + 50 W (8 Ω/ohms, 20 Hz – 20 kHz with 0.08 % T.H.D.) Usable Sensitivity: 1.2 μV (12.8 dBf) 18 μV...
Page 162 Index FM indoor antenna ············································· 18 Format ······························································ 118 Cable Decode Mode ·················································· 122 v Numerics Friendly Name ·················································· 128 Audio cable ······················································ 12 Deep Color ················································· 11, 150 Front A/B (connection) ································· 80, 87 2.1-channel ························································· 88 Coaxial digital cable·········································· 12 Diagnostics ·······················································...
Page 163 Playback ALAC·························································· 34, 49 Language ·························································· 132 Random ························································ 33, 65 Text Search ························································ 64 Auto surround ············································ 73, 77 Lch Level ·························································· 132 Rch Level ························································· 132 Tone ································································· 111 Blu-ray Disc player ··········································· 30 Levels ······························································· 125 Rear panel ························································ 140 Tone Control ·····················································...
Page 164 License THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT 3. License Grant. Subject to the terms and conditions of You may distribute the Executable Files and Source WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, this License, the Author hereby grants You a worldwide, Code only under the terms of this License, and You This section describes software license used for INCLUDING BUT NOT LIMITED TO THE WARRANTIES...
Page 165 n libogg n Tremor 9. Termination. THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY a. This License and the rights granted hereunder will http://www.xiph.org/ogg/ http://wiki.xiph.org/index.php/Tremor EXPRESS OR IMPLIED WARRANTIES, INCLUDING, terminate automatically upon any breach by You of any BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF term of this License.
Page 166 MERCHANTABILITY AND FITNESS FOR A PARTICULAR software for any purpose with or without fee is hereby Marantz provides the source code based on the GPL and PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE granted, provided that the above copyright notice and this...
Page 167 Dimensions Unit : in. (mm) 17 21/64 (440.0) 2 11/64 (55.0) 1 31/32 1 31/32 (50.0) 13 25/64 (340.0) (50.0) Weight : 18 lbs 8 oz (8.4 kg)
Page 168 D&M Holdings Inc. 3520 10244 00AM...

Marantz NR1604 Owner's Manual

Quick Links

Related Manuals for Marantz NR1604

Summary of Contents for Marantz NR1604

Table of Contents