Getting Started; Initial Settings Before Operations; Adjusting The Clock; Setting The Demonstration Mode - Kenwood KDC-BT42U Instruction Manual

Getting Started

Canceling the display
demonstration
The display demonstration is always turned
on unless you cancel it.
When you turn on the power (or after you
reset the unit), the display shows:
[CANCEL DEMO] \ [PRESS] \ [VOLUME
KNOB]
Press the volume knob.
1
[YES] is selected as the initial setup.
Press the volume knob again to confirm.
2
[DEMO OFF] appears.
If no operation is done for about 15 seconds
■ ■
or if you turn the volume knob to select
[NO] in step 2, [DEMO MODE] appears and
the display demonstration starts.

Setting the demonstration mode

Press the volume knob to enter
1
[FUNCTION].
Turn the volume knob to select [DEMO
2
MODE], then press to enter.
Turn the volume knob to select [ON] or
3
[OFF].
If [ON] is selected, display demonstration
starts if no operation is done for about 20
seconds.
Hold to finish the procedure.
4
6
English

Adjusting the clock

Press the volume knob to enter
1
[FUNCTION] mode.
Turn the volume knob to select
2
[SETTINGS], then press to enter.
Turn the volume knob to select [CLOCK],
3
then press to enter.
Turn the volume knob to select [CLOCK
4
ADJUST/ CLOCK ADJ], then press to
enter.
Clock hour flashes on the display.
Turn the volume knob to adjust the hour,
5
then press to enter minute adjustment.
Clock minutes flashes on the display.
Turn the volume knob to adjust the
6
minute, then press to confirm.
Press 4 / ¢ to move between the
hour and minute adjustment.
Hold to finish the procedure.
7

Initial settings before operations

Press SRC to enter [STANDBY] mode.
1
Press the volume knob to enter [FUNCTION] mode.
2
Turn the volume knob to select [INITIAL SET], then press to enter.
3
Turn the volume knob to make a selection, then press to confirm.
4
See table below for selection.
Hold to finish the procedure.
5
Item Selectable setting (Preset: *)
PRESET TYPE NORMAL/ NORM *: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ MW/ LW). ;
MIX: Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ MW/ LW).
KEY BEEP ON */ OFF: Activates/deactivates the keypress tone.
RUSSIAN SET ON: Folder name, file name, song title, artist name, album name are displayed in Russian (if applicable). ;
OFF *: Cancels.
P-OFF WAIT
Sets the duration when the unit will automatically turns off (while in standby mode) to save the battery.
––– : Cancels ; 20M *: 20 minutes ; 40M: 40 minutes ; 60M: 60 minutes
BUILT-IN AUX/ ON *: Enables "AUX" in source selection. Sound of the connected external component is produced through the
BUILTIN AUX car speakers. ; OFF: Disables "AUX" in source selection.
CD READ 1 *: Automatically distinguishes between audio file disc and music CD. ;
2: Forces to play as a music CD. No sound can be heard if an audio file disc is played.
SWITCH PREOUT/ REAR */ SUB-W: Selects whether rear speakers or a subwoofer are connected to the line out terminals on the
SWITCH PRE
rear of the unit (through an external amplifier).
SP SELECT OFF */ 5/4/ 6 × 9/6/ OEM: Selects the speaker size for optimum performance.
F/W UP xx.xx YES: Starts upgrading the firmware. ; NO *: Cancels (upgrading is not activated).
For details on how to update the firmware, see: www.kenwood.com/cs/ce/
CONTENTS
7
English