Getting Started of Bluetooth
PAR
VOICE
Press and hold to pairing mode.
Registering your Bluetooth device
with this unit (Pairing)
Press and hold
to enter pairing mode
1
"PAIRING" is displayed.
Any of the following is displayed
■ ■
depending on Bluetooth device
registration condition:
– "PLEASE PAIR YOUR PHONE": When
registering a Bluetooth device for the
first time.
– "(device name)": When a Bluetooth
device has already been registered.
– "DEVICE FULL": When a maximum of five
Bluetooth devices have already been
registered.
To cancel the pairing mode, press
.
■ ■
When registering a Bluetooth device for the
first time (Registering a Bluetooth device)
"PLEASE PAIR YOUR PHONE" is displayed.
2
Start registering this unit by operating
3
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit or audio unit (pairing).
Select "KENWOOD BT CD/R-5T1" from the
list of found units.
Input the PIN code ("0000") in the
4
Bluetooth device.
Check that registration is complete on
the Bluetooth device. PIN code is set to
14
English
iPod
"0000" as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page
20).
"(device name)" is displayed. Press the
5
volume knob.
The receiver is connected to a Bluetooth
6
device, with "HF CONNECT" or "AUD
CONNECT" displayed, and exits the
pairing mode.
If an error code is displayed during paring,
■ ■
see
<Troubleshooting> (page
31).
When a Bluetooth device has already been
registered, or maximum of five Bluetooth
devices have already been registered
(Selecting a Bluetooth device)
"(device name)" or "DEVICE FULL" is
2
displayed.
Turn the volume knob to select a
3
Bluetooth device name.
To register a new Bluetooth device, select
■ ■
"[PAIRING]", then go to "When registering
a Bluetooth device for the first time."
Press the volume knob.
4
Turn the volume knob to select the
5
profile for the device to connect.
"HANDSFREE"/ "AUDIO": The device can
■ ■
be connected using either a hands-free
or audio profile.
"HF/AUD": The device is can be connected
using both hands-free and audio profiles.
Press the volume knob to set up the
6
Bluetooth device.
"✱H✱A (device name)": The selected
■ ■
Bluetooth device is busy.
"-H-A (device name)": The selected
■ ■
Bluetooth device is on standby.
"(blank) (device name)": The Bluetooth
■ ■
device is deselected.
If two cell-phones or an audio player
■ ■
have already been selected, deselect one
device before selecting a new Bluetooth
device.
• "H" (HFP) or "A" (A2DP) indicates the
corresponding profile.
Press
to exit pairing mode.
7
Deleting the registered Bluetooth device
"(device name)" or "DEVICE FULL" is
2
displayed.
Turn the volume knob to select a
3
Bluetooth device name.
Press and hold the volume knob to delete
4
the selected cell-phone.
"DELETE" is displayed.
Turn the volume knob to select "YES",
5
then press to confirm.
"COMPLETED" is displayed.
Press
to exit easy pairing mode.
6
About the Cell-Phone
Version: Bluetooth Standard Ver. 2.1+EDR
■ ■
Profile:
■ ■
HFP (Hands Free Profile)
SPP (Serial Port Profile)
OPP (Object Push Profile)
PBAP (Phone book Access Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP (Audio/Video Remote Control
Profile)
CONTENTS
Registering from Bluetooth devices
(Pairing)
Press
SRC to turn on the power.
1
Start registering this unit by operating
2
the Bluetooth device.
By operating the Bluetooth device, register
the hands-free unit or audio unit (pairing).
Select "KENWOOD BT CD/R-5T1" from the
list of found units.
Input the PIN code ("0000") in the
3
Bluetooth device.
Check that registration is complete on
the Bluetooth device. PIN code is set to
"0000" as the default. You can change this
code. Refer to [PIN CODE EDIT] under
<Bluetooth Setup> (page
20).
By operating the Bluetooth device, start
4
hands-free connection.
If there are 5 or more Bluetooth devices
■ ■
registered, you cannot register a new
Bluetooth device.
For the cell-phones verified for compatibility,
access the following URL:
www.kenwood.com/cs/ce/bt/
The units supporting the Bluetooth
■ ■
function have been certified for conformity
with the Bluetooth Standard following the
procedure prescribed by Bluetooth SIG.
However, it may be impossible for such
units to communicate with your cell-
phone depending on its type.
English
15