Kenwood KDC-BT42U Instruction Manual page 7

Adjust [SETTINGS] mode settings
While listening to an iPod or KENWOOD Music Editor media ...
Press the volume knob to enter [FUNCTION] mode.
1
Turn the volume knob to select [SETTINGS], then press to enter.
2
Turn the volume knob to select [SKIP SEARCH], then press to enter.
3
Turn the volume knob to make a selection, then press to confirm.
4
0.5% (initial)/ 1%/ 5%/ 10% : Sets the ratio of skip when searching for a song in Music Search
mode.
(Holding 4 / ¢ skips songs at 10% regardless of the setting made.)
Hold to finish the procedure.
5
Handling discs
Do not touch the recording surface of the
■ ■
disc.
Do not stick tape etc. on the disc, or use a
■ ■
disc with tape stuck on it.
Do not use any accessories for the disc.
■ ■
Clean the disk by moving the cloth
■ ■
outward from the center of the disc.
Discs that cannot be used
This unit can only play the CDs with:
■ ■
A disc that is not round.
■ ■
A disc with coloring on the recording
■ ■
surface or a disc that is dirty.
You cannot play a Recordable/ReWritable
■ ■
About the Audio file
Playable Audio files:
■ ■
MP3 (.mp3), WMA (.wma), AAC-LC (.m4a)
Playable disc media: CD-R/RW/ROM
■ ■
Playable disc file formats: ISO 9660 Level
■ ■
1/2, Joliet, Romeo, Long file name.
Playable USB devices: USB mass storage
■ ■
class
Playable USB device file systems:
■ ■
FAT16, FAT32
12
English
Clean the disc with a dry silicon or soft
■ ■
cloth. Do not use any solvents.
When removing a disc from this unit, pull it
■ ■
out horizontally.
If the center hole or outside rim of a disc
■ ■
has burrs, remove them before inserting
a disc.
disc that has not been finalized. (For the
finalization process, refer to the instruction
manual that came with your disc writing
software or your disc recorder.)
3-inch CD cannot be used. An attempt
■ ■
to insert using an adapter can cause
malfunction.
Although the audio files are complied with
the standards listed above, the play maybe
impossible depending on the types or
conditions of media or device.
Detailed information and notes about the
■ ■
playable audio files are stated in an online
manual on the following site:
www.kenwood.com/cs/ce/audiofile/
About the USB device
This unit can play audio files stored on a
■ ■
USB mass storage class device.
Install the USB device in the place where
■ ■
it will not prevent you from driving your
vehicle properly.
You cannot connect a USB device via a USB
■ ■
hub or multi card reader.
Make sure all important data has been
■ ■
backed up to avoid losing the data.
About compatible iPod/iPhone
Made for
– iPod touch (4th generation)
– iPod touch (3rd generation)
– iPod touch (2nd generation)
– iPod touch (1st generation)
– iPod classic
– iPod with video
– iPod nano (6th generation)
– iPod nano (5th generation)
– iPod nano (4th generation)
– iPod nano (3rd generation)
– iPod nano (2nd generation)
– iPod nano (1st generation)
– iPhone 4S
– iPhone 4
– iPhone 3GS
– iPhone 3G
– iPhone
(As of January 2012)
About "KENWOOD Music Editor"
This unit supports the PC application
■ ■
"KENWOOD Music Editor Light ver1.1" or
later.
When you use the audio file with database
■ ■
information added by the "KENWOOD
Music Editor Light ver1.1", you can search
for a file by title, album or artist name using
the function mentioned in Music Search
(page 11).
In the Instruction manual, the term "Music
■ ■
CONTENTS
Connecting a cable whose total length
■ ■
is longer than 5 m can result in abnormal
playback.
This unit cannot recognize a USB device
■ ■
whose rating is other than 5 V and exceeds
500 mA.
When connecting the USB device, use of
■ ■
the CA-U1EX (option) is recommended.
The maximum current consumption of the
CA-U1EX is 500 mA.
Latest compatible list of iPod/iPhone.
■ ■
For details, see:
www.kenwood.com/cs/ce/ipod
Types of available control vary depending
■ ■
on the type of connected iPod. For details,
see above URL.
You can connect an Apple iPod/iPhone
■ ■
with KDC-BT42U.
The word "iPod" appearing in this manual
indicates the iPod or iPhone connected to
this unit with a connection cable, KCA-
iP102 (optional accessory).
If you start playback after connecting the
■ ■
iPod, the music that has been played by
the iPod is played first.
In this case, "RESUMING" is displayed
without displaying a folder name, etc.
Changing the browse item will display a
correct title, etc.
You cannot operate the iPod if "KENWOOD"
■ ■
or "✓" displayed on the iPod.
Editor media" is used to mean the device
that contains audio files with database
information added with KENWOOD Music
Editor.
"KENWOOD Music Editor Light ver1.1" is
■ ■
available from the following web site:
www.kenwood.com/cs/ce/
For further information on "KENWOOD
■ ■
Music Editor Light ver1.1", refer to the site
above or the application help.
English
13