Table of Contents
Advertisement
qtc9322c.pm5
Quick Talk Advanced Features/ Applications Manual
This manual, Ritron Item RQT-UM2, covers advanced operation of the Quick Talk Voice Notification Radio Transmitter,
including the more complex features not covered in the Basic Owner's Manual, Ritron Item RQT-UM1 (14500006).
For further information on the Quick Talk, visit Ritron's website at http://www.ritron.com, or call Ritron at 317-846-1201.
TABLE OF CONTENTS
DESCRIPTION
WHAT THIS MANUAL COVERS ............................................... ii
WARNING: IMPORTANT SAFETY INFORMATION .................. ii
ACCESSORIES FOR QUICK TALK .......................................... ii
GENERAL INFORMATION ........................................................ 1
QUICK TALK FEATURES ......................................................... 1
IDENTIFICATION OF CONTROLS & CONNECTIONS ............. 2
COVER GASKET INSTALLATION/ REPLACEMENT ............... 3
PROGRAMMING YOUR QUICK TALK ..................................... 4
PULSE TELEPHONE CONFIGURATION ................................. 4
TO PROGRAM QUICK TALK BY TELEPHONE ....................... 4
1. Configure Switch Terminals (1 or 2 switches) ................ 5
the Quick Talk Transmitter ........................................... 5
3. Programming Quick Talk Transmitter Frequency .......... 6
4. Setting a Special Transmit Frequency ........................... 7
Squelch Interference Eliminator .................................. 7
Squelch Interference Eliminator .................................. 8
7. Test Quick Talk Radio Transmitter ................................. 8
8. Testing Switch Open & Closed Conditions .................... 9
for Each Message Transmission ............................... 11
11. Programming the Switch Status
Broadcast Schedule .................................................. 11
12. Programming a Message Repeat Limit ....................... 12
Message Parameters ................................................ 12
Factory Settings ........................................................ 12
Normal Debounce ..................................................... 13
Holdoff Debounce ...................................................... 13
18. Using Latching Option ................................................. 14
Ni-Cd Batteries .......................................................... 15
20. Setting Analog Modes ................................................. 15
Analog Input Mode .................................................... 16
Terminated Alarm Input Mode ................................... 16
21. Recording Unique Low Battery Messages .................. 17
22. Recording Unique Power Failure Messages ............... 17
23. Enabling/ Disabling Status Messages ......................... 17
24. Setting Battery Saver Options ..................................... 17
25. Setting Narrow-Band (2.5 kHZ) Channels ................... 18
26. Connecting an External 12 VDC Power Supply ........... 18
27. Configuring Transmit Delay ......................................... 18
28. Pre-installation Checklist ............................................. 18
29. Quick Talk Installation .................................................. 19
CARE & MAINTENANCE ........................................................ 19
QUICK REFERENCE GUIDE ............................................ 20, 21
Page ii
WHAT THIS MANUAL COVERS
PAGE
................................
.............................
...................
..........................
.................
......................................
............
...............................
.....................
...........................
- - - WARNING - - -
IMPORTANT SAFETY INFORMATION
NOTICE: DO NOT use the Quick Talk unit to report conditions
relating to safety of life or property. To reduce the
risk of fire, electric shock or personal injury, follow
these basic safety instructions when using this unit.
1. Read and follow all instructions.
2. Disconnect the unit before cleaning. Do not use liquid or
aerosol cleaners.
3. Use only approved power sources for the unit.
4. During thunderstorms, avoid contact with this unit and any
external antenna system or wiring.
5. The Quick Talk switch and external power terminals are
connected internally through ground to the antenna connector. If
the Quick Talk switch or power supply terminals contact high
voltage, a hazardous condition may exist in that contacting the
antenna could prove injurious or even fatal.
6. In general, the switches you connect to the Quick Talk are to be
independent dry contact switches, and not part of any other
"live" electrical circuit
7. If you are unsure whether your installation will be safe, contact
an experienced electrician or electronics technician.
ACCESSORIES FOR QUICK TALK
These replacement and optional items are available from Ritron
and its authorized dealers.
ITEM
DESCRIPTION
AFB-1545
Standard 16 in. Flexible Whip Antenna
RAM-1545
Magnetic-Mount Antenna w/ 20 ft. Cable
& BNC Connector
TABLE OF FIGURES
DESCRIPTION
FIG-1: CONTROL & CONNECTION LOCATIONS ................ 2
FIG-2: COVER ASSEMBLY ................................................... 3
FIG-3: CONNECTIONS FOR TESTING SWITCHES ............ 9
FIG-4: TYPICAL MESSAGE CONFIGURATION ................. 10
FIG-5: CURRENT LOOP .........................................................
(EXAMPLE CONNECTION DIAGRAM) ................... 14
ALKALINE BATTERIES .......................................... 15
FIG-7: J103 POSITION FOR USE WITH .................................
NI-CD BATTERIES ................................................. 15
FIG-8: ANALOG INPUT MODE (EXAMPLE) ....................... 16
FIG-9: TERMINATED ALARM INPUT MODE (EXAMPLE) . 16
OPERATION .......................................................... 18
FIG-12: QUICK TALK INSTALLATION ................................ 19
PAGE
Advertisement
Table of Contents
