Table of Contents
Advertisement
Page 11
10.
NUMBER OF RECORDED
VOICE PHRASE REPEATS
FOR EACH MESSAGE
TRANSMISSION
What is the purpose of setting the number of times the
Voice Phrase is repeated in each Transmission? Your
previously recorded voice phrase can be programmed to
repeat from one time to nine times in each Quick Talk
transmission. You may wish to use more phrase repeats
for more urgent messages.
EXAMPLE: The recorded location phrase ("Well 3"),
and switch condition phrase ("Pump motor hot"),
when programmed to repeat two times in each
message transmission, plays back:
"...beep. Well 3. Pump motor hot. Pump motor hot. beep..."
The beginning and ending beeps are added
automatically to attract attention to Quick Talk
message transmissions.
Do I need to program this feature? The Quick Talk is set
at the factory to play each recorded voice phrase one time
in each transmission. If this is sufficient for your
application, you can skip to the next section, in which we
explain how to program the transmission itself to be
repeated at different intervals.
NOTE: The following examples are for Switch #1. To
program this feature on Switch #2, refer to Quick
Reference Guide dial codes on pages 20 and 21.
To Program the Number of Times the Switch Open
Phrase is Repeated in Each Transmission:
1. Pick up the telephone receiver; listen for the tone.
2. Dial "711" then a single digit indicating how many
times you want the voice phrase repeated in each
transmission, as shown in Table 4.
EXAMPLE: To repeat the phrase three times,
dial "7113."
Wait for the confirmation tone after dialing.
3. Hang up the telephone or continue programming.
To Program the Number of Times the Switch Closed
Phrase is Repeated in Each Transmission:
4. Pick up the telephone receiver, listen for the tone.
5. Dial "712", then a single digit indicating how many
times you want the voice phrase repeated in each
transmission, as shown in Table 4.
EXAMPLE: To repeat the phrase five times,
dial "7125."
Wait for the confirmation tone after dialing.
6. Hang up the telephone or continue programming.
— TABLE 4 —
VOICE PHRASE REPEATS
IN EACH TRANSMISSION
.............................
1 time
............................
2 times
............................
3 times
............................
4 times
............................
5 times
............................
6 times
............................
7 times
............................
8 times
............................
9 times
For assistance, call RITRON at 800-872-1872, or go to http://www.ritron.com
®
Quick Talk Features/ Applications Manual
11.
What is the purpose of programming a Broadcast
Schedule for Switch Status Transmissions? You can
program different switch status transmission schedules
for the open and closeds condition of your switch.
EXAMPLE: The switch status message for switch
Do I need to program this feature? Quick Talk is factory-
set to transmit a switch status message one time with
each switch change. Skip to the next section if the default
is sufficient for your application.
NOTE: The following examples are for Switch #1. To
To Program a Broadcast Schedule of Switch Status
Transmissions for the Switch Open Condition:
1. Pick up the telephone receiver; listen for the tone.
2. Dial "511", then the one-digit code from Table 5,
3. Hang up the telephone or continue programming.
To Program a Broadcast Schedule of Switch Status
Transmissions for the Switch Closed Condition:
4. Pick up the telephone receiver; listen for the tone.
5. Dial "512", then the one-digit code from Table 5,
6. Hang up the telephone or continue programming.
MESSAGE SCHEDULE
Never send messages for this condition
CODE
On switch condition change only
NUMBER
Every 30 seconds
Every 1 minute
1
—
DEFAULT
Every 2 minutes
2
Every 5 minutes
3
Every 10 minutes
4
Every 30 minutes
5
Every 1 hour
6
Every 2 hours
7
8
9
PROGRAMMING SWITCH
STATUS BROADCAST
SCHEDULE
open is "Pump motor temperature OK." To know
Quick Talk is operating properly, schedule this
message to transmit once every two hours.
The corresponding switch status message for
switch closed is "Pump motor over temp-
erature." So this situation receives prompt
attention, schedule this message to transmit
once every two minutes.
program this feature on Switch #2, see the
Quick Reference Guide on page 20.
below. Wait for the confirmation beep after dialing.
EXAMPLE: To schedule switch open message
for every two hours, dial "5119."
NOTE: The factory default is "5111": transmit
message on switch change only.
below. Wait for the confirmation beep after dialing.
EXAMPLE: To schedule switch closed message
for every two minutes, dial "5124."
NOTE: The factory default is "5121": transmit
message on switch change only.
— TABLE 5 —
.....................
.......................
......................
......................
.....................
.....................
.........................
........................
Page 11
CODE
NUMBER
..
0
.......
—
1
DEFAULT
2
3
4
5
6
7
8
9
Page 11
Page 11
Advertisement
Table of Contents
