Advertisement
I ncorrect cable adjustment couId cause
the wheels andtines to rotate unexpect-
edlyi
Follow adjustment procedures
carefullyi Failure to do so could result
in personal inlu_ or prope_ damage.
4 Checkfor correct spring/cable tension
aSinstructedinSection5;Checkingand
Adjusting ForwardClutchBelt Tension.
,,, ..., __ ,,_,,,
.,,, ,.,
..
5. Whentension is correct; tighten the
Figure 2.12: Attach
Wfleei Gear Lever
two iam nuts (B_securely
(b)If adding only a few ounces of gear oil
_
uSeAP iaied GLi4 oi GEi5 geai oil hav ng
STEP 5: CHECK TRANSMISSION
a viscosity of SAE 140; SAE 85W,140 or
•
:
mission
use only GL,4 gear oil having a ...........
Thetransmiss!on was f!lled w!th gear o!l at.
i.,
k,;
_;:
VISOOSll:y Of hAL UbVV 14U or bat: ]qU
the factoryi However; be sure to check the-
oil levelat th is time to makecertainit is
(c)Usi ng a cleanfunnel; slowly add gear
R
correct,
oil until it flows from the gear oil level
i
IMPORTANTiDo noi o ieraie i he iiller if
checkh ole(N, Figure 2-11)
the gear oil levelis Iowi going so will
(d) Reinstalland tighten securely thegear
iesuli in seveie damageto the transmisi
oil fill plug (Mi Figure2-1 O)
sloncomponents.
STEP 6: ATTACHWHEEL GEAR LEVER
n I v I r
n
Ilth
Figure2 13 Attach wheelgear cable and
1 With the tiller o
e egou
d;pu
'
1, Insert the Wheel Gear Lever (Pi Figure
i
.
i
.
v r
" r
utchcablewlthcab eties(S).
Depth Regulator Le
(R, F!gu e
2,12)up through the slot !n thecontrol
back and then slide it to the second notch
.....
: panel
that is labeled WHEEL GEA&
.fromthe mp NOTP If the rover does
_i_ _C
_}_i _X,_
:1 ..'
i'.
Insert two #_U-o/x UZ round Ilead
move, h.fttne tlne hOOd flap ano lOOK.for a ii
_..#X
i
screws down through the
irl_o
M,,
plastic tlesecurlngtheeverlnplac
Cut
th cntil
ne
I nd e reI
tt
h
_:.:.'e
_o o pa
e _aa
scu
ya ac
and remove me _mi
ihe wheel geai mouniing biacket using
2i Removethe oil levelCheckplug (M;
two #t0 Iockwashersand #10:32 nutS:
Figure2-10)on the left-side of the trans-3
Used small board to tad theWheel
mission. (Due io dried paint on ihe plug
Gear Lever knobsecurely onto the levei.
threads it may require some force to
.....
......
4 Secure the wheel gear cable and the
remove the plug the first time )The gear
:
:i
reverseclutch control cable to the left-side
011level is correc[
i.f Oll sEar[s £o TIOW OU£01"
;.-
_i;
_ ,._; _i; _
nanaleoarWl1:n l:wo plasl:lC l:les
i-ig ure
then°iea_tu_piuui_'em°veu
"Su'
2 1
Itd
ottw
let
_
.
'
-3)
oca eab
u
o
eapa 4S
p
securely reinstall the plug
'
off any excess tie length with
SClSSOrS_
STEP 7: CHECK AIR
PRESSURE IN TIRES
Use a tire pressure gauge to check theair
pressure in both tire& Deflate or inflate
both tires eq ually to between 15PSI and
20
PSI)i Be sure that both tires are
,,,inflated
equally or the unit will pull to one
I-#gure z-Tu: _ear o# mve# cnecK pmgi
sidei
3; If oil does not flow from the check
fluid or motor oil in the transmissioni
Inspect the hardwareon the unit and
Li _'_
_
_i
_ ;_ _iiiL_i_
tighten any loose Screws;bolts and nuts
(a] umanarea around
_ne fin Ilo_e
tin,
Figure2,11)and unscrew gear Oilfill plug:
Advertisement
