Advertisement
4: With the forward clutchcable (N,
Figure2-4)on the inside of handlebar,
position the handlebar ends on the outside
of the two mounting tabs (M, Figure 2-3)
on the transmission top covc
NOTE: The curved handlebar height
STEP 4: ATTACH FORWARD
CLUTCH CONTROL CABLE
1: Removeany fasteners (rubber bands;
tape, etci) that may secure the Forward
Clutch Control levers (Ji Figure 2-7)to the
handlebari
adjustment bracketappears as shown In
Fi..ur e
2 5:
Carefull;unwra"Wheel
r
....... _..............................................
.....................
;.................
y
_ ,
y
p
U_a:
..................
C; Figure2i3 for non-electric start un!tSl_everan
# moveleverto
Forelectric stag units, the bracket is Ioos-of
f the la_oim
_
ened and moved to one side
P
'
NOTE: The Wheel Gear Leverwill be
5i Loosely attach the handlebarsto the
installed later in ins p¢oceduie
I
mounting tabs with two 3/8#16×1
1
I
i
:
IMPORTANT' Use the DISENGAGE posi.
screws (heads of screws go to Inside of
:
....
_,_ ._0ii _1_ _,_._ _
only when the engine is riot running
tau_.l;,_/o m w<_s,ers<_na o/o!, v,OuK'
,.
_i_; ;_ ,,
Before starting the engine; the Wheel Gear
,uL_ !ui rluu_ 5i_!'
Lever must be placedin the ENGAGEposii
tion
(see Section 3 for details).
Figure
2;7:FetwardClMcfl
Controllevers
CLIITCH CONTROL CABLE
2: The forward clUtChcontrol cable (with
control
cable (H,F gure 2:6)from its Sh
i22 _ _i_.2_22 _
_2,1 ,u
:_
',
;_
kink or s[reLcnthe cal_,eiinset[ [l]e z-con-
ping posll:lOn ano rou[e i[ up along [ne
x,x..x;
r=xi;, _o
_
_._ _., xx;i
inslde edge of the left slde handlebar: A
::
:_ ;
isinstalled on
'n[° me no,e al:me eno
the
cable,
Je(Ki Figuie2i 7)
61 On electric start units, reattach the
heightadjustment bracket (A; Figure2-2)
Tighten bothscrews securelyi Make sure
the handlebarcross-brace (B; Figure2-3)
is under the bracket.
7: Move the handlebars u ) or down to
align the threadedhole in the cross-brace
with one of the four slots in the curved
height adjustment bracket: Placethe
Left Side
Reverse Clutch
Handlebar
ControlKnob
Slotin
Control
Figure2,8
keyedwasher (E Figure2-3)onthe flange
head height adjustment screw (F) with the
3; Attach the cable adjuster (A; Figure
raised keys (edges)of the washer facing
2-9)to the bracket on the right-s ide han-
downi
Figure2,6:Attach reverseclutch control
!n
Thi._ih
_h_in hi _rli,mtm_ni _r_w i
assembly to slotted holein handlebar
the two jam nuts (B} jast enough to slid
Fiour'e2"3: i_o _
hole'_nthe hand eba'r'
the Cableadjuster onto the bracket: Then
g-)
2i Insert the cable into the slot in the
hand ti, hten the iam nuts
crossfbrace; making suie !hat !he raised
coniiol panel and fii the threaded assemi
keys on the washer fit into the slot on the
bly into the hole in the slot (see Figure 2-
heightadjustment bracketi Tightenthe
6)Be sure that the flat side of the
heightadjustment screw securely. Nexti
threadedassembly is aligned with the flat
securelytighten thetwo screws and nuts
side of the holei Slide the hexnut (I)up
in the ends of the handlebar (Mi Figure 2-
the cable and tighten it securely
3)
9 To remove the tiller from its shipp ng
control cable by pulhng the knob out and
pla_ormi first carefully unwrap the wheel
il
in it TI_
h
I r t rnt
it
......
eeas g.
e
obs cud eu
o s
gear cable (wzth attached lever, see Rgure
:i
:
r
......
...... ....
neutral posit on against the tape ed
............................................................................
2:5) from aroundthe chassis Movethe
:.
Figure 2_9
_,,7
;" _.Z_C2_.._
bushingi If It doesnt, contact your local
wnee bear Lever_Ll_:omeu_l:i'_L1ALll:
ir
it h f t
f r t
hni I
.;idea
e
o
e
ac
o_
o
ec
ca
pos!t!oni4h!s allows the wheel s to rotate
assistance'
freely;Use the handlebars to roll the tiller
Advertisement
