Advertisement
W!_f_Y/'-_I
;]OIIO[tl
Beforeinspecting;cleaningor servicingthe machine;shutoff engine, wait lor all moving parts to come to
I
a completestop; disconnectspark plug wire and move wire away lrom spark plug
_dl16(
i Failure to lollowthese instructionscan result in serious personal inju_ or propertydamagei
t
IjJ
I
3; Slip the forward drive belt down and
over the front of the transmissio n pulley
(C; Figure5-16). NOTE:For additional
working room; loosen the reversebelt
guide (Vi Figure5-12) and twist it out of
the way
41 Put the lower half of the belt into the
Highspeed greeve (middle groove)or the
Low speedg reeve (rearmost g reeve) of
the transmission pulley (C; Figure5-t6);
&Put the upper half of the belt in the High
speed g reeve (greeve closest teen gine)
or t he Low speedg reeve (rearmest
groove) of the engine forward d rivepulley
(D; Figure5-16)
IMPORTANT:Make sure that the forward
drive belt is to the insideof the wire belt
guide (I; Figure 5-t2)and the forward idler
pulley(J)
6:If you loosenedthe belt guide; wait until
3; Slip the reverse belt off the engine
reverse pulley (Ai Figure5-18)i If neces-
sa_i work the belt off the pulley with your
left hand while pulling the engine recoil
starter rope with your right handi
4: Pushthe upper half ef the reverse belt
downward to create slack in the bell Then
reach underneaththe transmission and
slip the belt off the front of the transmis-
sion pulley (B, Figure5-t8).
5: Pull the belt up and past the engine
reverse pulley (Ai Figure5-18)i
Bi Installing the Reverse Drive Belt:
1 : Slip the reverse belt down between the
eng!ne reverse pulley (A; Figure 5-t8) and
the engine forward drive pulley (C).
2i Loop the bottom half ef the belt over
the front of the transmission pulley (Bi
Figure5-t8) and seat the belt in the front
Figure5-18*
Removing andinstalling reverse3
Placethe belt tO the inside of the...............
securing the belt guide:.
............ .................
.........
i
;
#elt:reverse
idler pulley (D, Figure5q8)and
7 Ins[all the reverse drive belt
ih i v¢
It
i"
;V Fi € ;i2:
e eeseDe
guee(gueb-+).
A Removingthe Reverse Drive Belt
8: Install the beltcover and secure it with
Thenslip the upper end intothe groove ef
1 Stop the engine and allow it to Coo_
•
:
the two nuts.
,
:;.
_
i;
the engme reverse pulley (A, Rgure5-18).
DeTore WOrKn( nearme De_s: _esureme
9 If you installed a new belt;check the
r
I i"
:
i
4 If the reverse beltguide (Vi Figure5q2)
'
:
spakpugwrelsdsconnectedanden
•
......
tension after two hours of operaben
electric start models the ionitionkev is
was loosened previously; Centerthe belt
(eve_ t0 hours theieafter)re_oved_
_
i
_
"_
_
guide on ihe beli and tighten ihe mounting
Screwsecurely
R
EDRIVEBELTREM
VALAND
2 Remevethe belt cover by remeving the
REVE
S
O
INSTALLATION
!we nu!s Foi easiei access !o the !ians f
5hel_toallntuhte
b_ltt_O_oeran_rSeCsUr_s_tiwnlth
.......
:
mission (lower)pulleyi remove the trans_
+
NOTE: The forward drive belt must be
......
......
...... r cover
was emoved, reinstall i't with the
in_t_ll_, h,,f_r_ in_t_llin, th_ i,,ve¢_,,,iiv_
mission cover located below the trans-
be'_i."_ _
°_"
_
mission pulleyi
tea! selfi!apping screwsi
Advertisement
