Advertisement
Tuner
Severe
hum or noise/stations
cannot
be
received.
("TUNED"
or "STEREO"
flashes
in
the display.)
• Set the prope:
band and fiequency
(page 15).
• Connect
the antenna
properly
(page 8).
• Find a place and an orientation
that provide
good
reception,
then set up the antenna
again. If you
cannot obtain good reception,
we recommend
you
connect
a commercially
available
exte:nal
antenna.
• The supplied
FM lead antenna
receives
signals
along its entire length, so make sure you exWnd it
fiflly.
• Locate fl:e antem:as
as t:ar away flon: fl:e speake:
cords as possible
• T!), turning off SU:Totmding electrical
equipment
A stereo FM program
cannot
be received
in
stereo.
• Pless FM NIODE _epeatedly
until "STEREO'
appears.
Tape deck
The tape does not record
or play, or there
is a
decrease
in sound
level.
• The heads
me di_y. Clean them (page 38)
• The recor@layback
heads are magnetized.
Demagnetize
them (page 38)
The tape does not erase
completely.
• The _ecord/playback
heads are magnetized.
Demagnetize
them (page 38)
There is excessive
wow or flutter,
or the sound
drops
out.
• The capstans
or pinch _ollas
me di_,
Clean flwm
(page 38)
Noise
increases
or the high frequencies
are
erased.
• The _ecord/playback
heads are magnetized.
Demagnetize
them (page 38)
The tape does not record.
• No cassette
is loaded.
Load a cassette.
• The tab has been removed
flora the cassette.
Cover fl:e broken
tab with adhesive
tape
(page 38).
• The tape has wound to the end.
Transmitter
(MHC-GX750
only)
There
is no sound.
• Check the connection
of the optional
component.
• Check tha_ the optional
component
is turned on.
• Tmn up the volmne on the connected
optional
component,
if the transmitter
is connected
to the
headphones
jack.
• Change the radio fiequency
using the CHANNEL
selector
on the transmitta,
then press WIRELESS
on the unit again.
• If you connect
tlle transmitte!
to the analog out
jacks of an audio reproducer,
make sure that the
NOISE
FILTER
switch
is set to OFF.
• Make sure that the NOISE
FILTER
switch is set
to either ON or OFF (If the switch gets stuck
between
ON and OFF, the sound will be cut oft)
There
is severe hum or noise.
• If the transmitter
is connected
to the headphones
jack, turn down the vohune
of the connected
optional
component
If the connected
optional
component
has the BASS BOOST
or MEGA
BASS fimction, set these fimction
to OFF
• If file connected
optional
component
has a LINE
OUT jacks, connect
its LINE OUT jacks.
• Change
the radio frequency
with the CHANNEL
selector
on the transmitter
then press WIRELESS
on the unit again.
• If you connect
file transmitta
to the analog out
j acks of an audio reproduca,
make sme that the
NOISE
FILTER
switch
is set to OFF.
If the
system
still
does
not
operate
properly
after
performing
the
above
measures,
reset
the
system
as follows:
Use buttons on the unit lbr the operation.
1 Disconnect
the power cord.
2 Reconnect
the power cord.
3 Press II, PLAY MODE/TUNING
MODE and
DISC 1 at the same time.
4 Press I/_
to turn on the system.
The system is reset to the factory settings. You
should set the settings you made, such as the
preset stations, clock, and timer.
-4
8
¢0
o
5'
Advertisement
