Poulan Pro 1425 Operator's Manual page 8

I
C. CHAIN TBNSION
• C_lin Tetaion hJvery hnportsnt- -
- A loom chain will wur the bar m_l itee_.
- A loom eb_n etn jump off the her whlls you
it_ro _
- Aright_t_ san break or damsge the mtw and/
or bar.
• The ehain etretoheJ dm4ui use, em_ecislly
when new. Cheek tem_on ,_-i0dical!y as Totlows:
-eaeh time the taw Is udKI;
- more frequently when the chain is new;
- e8 the chain warm8 up to normal operating
tmaperature.
& WARNING I
Avoid Imeldental ot_lng. Alw_pnplug the[
uw from tho power muroo beforo o'hafal
ten_oninl_ m"bdore tn_tsnJz_ 8 bar or ehain. J
J A w_'t_qG [
Always wear dlovm when hanming the e, b a_[
qNm e_sdn J881_trp sad esm eut you even when it [
Jt not movin_J
• _hmJa teaaldon Js eorteet where the ehah_
-- san be ll/tml about 1/8" from the guide l_r at a
point near the middle oft_e b_r.
With your unit unplugged, check your chain to
make Jure it is properly tensioned.
• When lmwr ehnin nee_ tensinoing, use the-
foUowtng prom,din'e:
It is remmmended that the ssw be turned
ul_ide down for chain teasioning.
1. Unplug the unit fi_omthe power source.
2. Lessen her nut8 until th_ sre only fml_" tight.
8. Tufa the tdUuath_Jcrew eloekw_e uatll the dri_o
Ikdte e*_ the ehain e_ter the g_de bet groove_l_-
ure 11 (inset).
To tighten the chain, turn the _Uueting
scTewdockwiu; to laosen the ehein. _m the ad_
Justin8 eerew counterdockw_. Figure 1t
4. Cheek th• tenmon by ti_kiag the chain from the
guide bar. Rolaove some ofths stiff_eim in the
ehein by pulling down and letting go of the thsin
severs] times. Fisure 12.
6. Continue turning the a_juating _rew until the
t_sJon Jscol't_t. _/8t1_912(tn_e_),
6. Tighten her mountlng nuts with a wench.
7. Recheck _ain tension.
A_us_ing
Figure 11
D. EXTENSION CORD ATTACIIM_NT
way. Ifth, pl_ does not f'_ fully into the extension
I. Use only cm A._ voltage supply idemtim] in cerd, revarse th_mrd. Ifit _/ll doesnot fl_,mahe sure
yOUhave a pohu_ed exteg_m mrd. If the egtenston
that shown m the nameplate of .q_ unit. cord doe, not fit into the outlet, rever0e the _rd. If it
2. ThemL_emdon eerd _ to reach the power _ don not fit into the outlet, centa_ a qualified
aouree must bet electrlciantoimtall thepro_er outlet. Do net change
a. Poim'/=eda_dmpeclflcsllymarked tomtit- thepinsor meks4oftheumtorextensinueo_dinsny
abIe for outdo_ use. The cerd nuat be w_
1
the powe_ Jouree the hall teugth of the e_.
tensiou cord to the unit. Oth_wise, loss e_
power 8nd ove_hes_b_g san 0c_Lr _ing dam.
a_eto the trait. Refer to Fijure 14 for minimum
wire gm_s r_ommencktiens. The cord must b_
marked with theprOper wirelau_z. U_pproprl-
ate extemdon _r_s are available.)
In _ eondltinn. Cord insulation must be
_,tact with no cracks _ deted0reUon. Plugeon. l P,,.'_msion Cm-d
aeetom mu0t he undamaged. If €ord or plugs m-e
damaged, replace before tn_ng the unit. F/gum 18
8. 8e6_are mtt4ms/on eerd te the powe_ cord as
a_ovm in Figure 13 to prevent diseonueeflon.
4. Insert the ertm_don cord socket into the ping on
the unit. l_re 18
To redum the Hsk ef eleetric 8hock, this unit hu a po.
|artzed plug (one hhuta is wider than the other}. This
plug wfl] fit in a pohu_ed extension card on]y one
--8--
MINIMUM _ GAUGE {
I_,_OM_F_DA'I_ONS (120V)
2_;A(V,Sm) [ 601tll6m) [ IGOit(_Om)
16A.W,O," ] le&W.O."
J . I4A.V_G.*
•_m_,,*w_o._, Figure 14