Poulan Pro 1425 Operator's Manual page 17

C. STOI_GE
When you_ msw fa to be stored for over aOda_,
_w_:
1. Drain oil fro_ off tank.
Wear prot_etSve itovmwheubJm-
dling the ohsJ_. The ohein is ehorp eud can
_tt you even whim it is not moving.
2. Remov_ clmm, and d_ the bar stud el_Jn.
D. SPROCKET/GEAR ASSEMBLY
• Clean the sproeket mtd mUToundlng area
daily dm-lng nuvy use of'the law.
• inSl_ttselq_'_._u_.rez_sl_foYwe_. A
_ eprocket will €8_ the chain to run errati-
ca.l_ m._clwm Jd_,;e, the life of tho bzr_nd ch_;n.
_,re 89.
• If sprocket is worn (Ftjpn_ S9), have the
8pl'6ekei replaced by Fmlr Authorlzod See-
vice Dealen User spr_€_ rephscmne_t _n
cause the doubis Lnsulat_s Watem to become ;,',-
ef_ve and am h_c_ase the rbk of ele_e
,hocE
3. Store tLe ohainin a container fined with oil topl_
vent rust.
4. Apply a €oating of oil to the en'dre suri_0e of the
bar 8ncl wrap It ht heavy paper, cloth, or t_htstie_
8. C]een the outside e_u.f,p_e of the u.rdt,
6. Store the Mw unpl_ in a dry place out of the
re_eb of children.
Figure39
E.TROUBLE 8HOOT/NG CHARY
]_md and follow all Warakng and Safer F ][notruotions before servicing your ul_L
SYMP'roM
09 i_uat_ for
bar and ehabs
htbricatJea.
_x_ndomuot
movewhm U_g_e
_iteh k enpq_L
C/ufinclatters
er cut_reughl_
C_Sn ste_ _4tl_n
cut.
Chah_ _ et en
an_e.
CMJSR
_. ou tank mpt_.
_. Oiloutlet eJo_zed.
8. Guide bar otlliole blocked.
: _. Guidebar ra_pinched.
& '1'r'_SerSwiSh 6_1]ure.
14. Circuit breeker tr4/_fuse blown_
iL _3hain ten.on incorrect.
Cut+_a damag_
3. Ghain worn.
4. _ du/I, hnpro]per]7 f_rpened, or
1. Cl_ln cu_er top_ not fil_l flak
:L Guidebsr burred or bent; rails uneven.
1. _tte_ damesed ,0n one side.
2. Chain dull on one aids.
& Gttide bar beat er wm'n.
_DY
L Ir-dloil t_nk,
2. C_act3_ur Authorized 8ervteeDeele_
_. Remove bar and clean.
2. RepOtorr_ls_
8. C0rA_t your Authorized _vic* Dealer.
4. Reaet dz_cuit breaker/mphtm fitm.
1. See "Chedn Te_len,"
_. S_unVe_ orrepl_ ch_
8. Re_barpen o_ repkm cha_
4. Seethe ehednehml_enlngin_tiom.
S. C0ntact y0ur A_lsorized Servke Dmd_
1. Seeth_ ehsin shssl_utng _.
2. Repek orrepl_ep_ide b_
1. Reaharpen until _dl _._ttere have equal
angles end length_ _ replace cha_z.
i_. Resin until dl cut*_s b_ve equsl
an_ee and lenl_hs or replam ehah_
_,_. Replace S_._i4e
b_.
NOTES
- 17-