Table of Contents
Advertisement
-
Maybe
batteries
in remote
are weak,
dead,
or installed
incorrectl_.t
Put new
batteries
in the remote.
(Note,
if you
remove
the
batteries,
you may have
to reprogram
the remote
to operate
other
components.)
-
You might
need
to drain
the remote's
microprocessor:
remove
batteries
and press
the number
i button
for at le:tst 60 seconds.
Release
the
i button,
replace
the batteries,
and (if necessary)
program
the remote
again.
Problems
with
DVI-HDTV
Connection
-
Make sure the I)VI device is turned on and the cables are firmly connected.
If problems
still occur, turn off your device. Re-connect
your device. Reset the power by unplugging
the power cord and plugging
it back in.
*
If you are tuned to the DVI-HDTV input and you're receiving Unusable
Signal message on-screen,
contact the manuthcturer
of the
DVI device *_r fflrther assistance.
If you tune to the /)VI-HDTV input and you see snow, the video goes in and out, or the video takes a long time to appear, your DVI
device is having trouble sending video information
to the TM Re-connect
your device. Reset the power by unplugging
the power
cord and plugging
it back in. If problems
persist, try connecting
to the Y Pb Pr jacks instead if they are available or contact the
manuf:tcturer
of the DVI device *_r further assistance.
If you have bars on each side of your picture, the device you connected
might have a switch or a menu option allowing you to
change the picture *_)rmat output
that will fix this. Choose either 720p or i080i.
Problems
with
V-Chip/Parental
Controls
The rating
limits
don't
work
-
You must lock the settings. (',o to the MAk\ Mk_\L' (t)r_ ss MENU on your remote), select Parc_ta/Cm_tro/,
select Loch Parc_ta/
Co_ tro/s.
I don't
remember
my password
and I want
to unlock
the TV
*
If you forget your password,
press MENU, then select Par_,_zta/O,m'ol
(the password
entry screen appears).
Simuhancously
press
and hokt CH+ and VOL+ on the TV's *iont panel for 8 seconds. The Parental control menu appears
on the screen, and you can re-
enter a password
via Loch Parv_ta/Cm_trol.s-.
The V-Chip
won't
let me watch
a program
even though
it's not rated
as violent.
Maybe the movie was given an NR (Not Rated) status. A_er you block movie ratings, you must set XR to Wcz# separately in order to
view movies with an NR rating.
What
Else Can !
If you've been through the Troubleshooting
section and nothing
has fixed your problem,
try rebooting
your TV. Note that after a
reboot you may need to run your TV through the setup process again. To do a reboot, unpklg
the power cord fiom the wall outlet,
power strip, etc. Keep your TV unplugged
for about 5 minutes. Then plug the TV back in, turn on the TM and see if the problem
is
fixed. If the problem remains, then please visit www.rca.com"television
*_r updated
FAQs or contact RCA Customer
Support at the
support
number provided
in your Warranty under Ho_ To <;vt &,rtdce.
How
Do ! Replace
My Remote?
-
If you need to replace your remote, call 1-800-338-0376. Your remote part number is R401A1. A shipping
and handling *_e will be
charged upon ordering,
and the appropriate
sales tax. Have your Visa, MasterCard or Discover Card ready.
Chapters
57
Advertisement
Table of Contents
