Care And Cleaning - Jenn-Air CCG2523 Guide Manual
Sealed gas cooktop
Hide thumbs
Also See for CCG2523 Guide:
- Service manual (84 pages) ,
- Installation manual (21 pages) ,
- Cooktop manual (9 pages)
Table of Contents
Advertisement
Care and Cleaning
6
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Be sure all controls
are OFF and all cooktop
parts are cool before cleaning.
Parts
Cleaning
Chart
Cleaning
Procedure
Control
Knobs
• Remove knobs in the OFF position by pulling each knob straight up.
• Wash in dishwasher
or in warm, soapy water. Do not soak or use abrasive
cleaners
such
as steel wool pads. Rinse and dry.
• Replace knobs, matching
the fiat part of the knob opening
with the fiat part of the shaft.
Make sure knobs are in the OFF position.
NOTE': When knobs are removed fi)r cleaning,
be car_,Jul not to spill liquid_ through the holes in
the control area.
•
•
*
*
•
•
•
•
•
•
,i,
*
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*
•
•
•
•
•
•
*
•
¢
•
•
.
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
o
•
•
•
•
•
•
•
Glass Cooktop
• Wipe with a clean, damp sponge or cloth. Rinse and dry thoroughly
to prevent a filmy residue.
A glass cleaner may be used to remove smudge marks and stains.
•
*
•
•
•
•
*
•
•
•
*1•
•
•
•
•
•
•
*
•
•
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Ignitors
• Clean with a toothbrush
and warm soapy water. Rinse and dry thoroughly.
DO NOT STRIKE
or PRY the ignitor. (Refer to illustration
of surface burner head,)
Porcelain
• Never wipe a warm or hot porcelain
enamel surface with a damp cloth. For general
Burner
Pan
cleaning,
wipe with soapy cloth, rinse and dry. To remove grease, spray with
cleaners
such as Fantastik
or 409*.
DO NOT use abrasive
cleaning
agents.
They may
damage the surface.
Surface
• Wash them with warm, soapy water and a nonabrasive,
plastic,
Burner (;rates
scrubbing
pad or in the dishwasher.
For stubborn
soils, clean
with a soap-filled,
nonabrasive,
plastic pad or Cooktop
Cleaning
Creme*
(Part # 20000001 ) and a sponge.
T_
NTP*TION
• The grates are made of porcelain
on cast iron and are very
durable,
however,
they will gradually
lose their shine and/or
discolor.
This is due to exposure
to high temperatures
from the
gas flame.
When replacing
the grates, carefully
align the lab on the grate with the indentation
in the
porcelain
burner base.
If the grates are not properly
aligned, they may rock.
•
•
•
•
•
•
•
•
•
•
•1•
•
•
•
•
•
•
•
•
•
°
•
•
•
•
•
•
•
°
•
•
•
•
•
•
•
•
°
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
*
•
Surface
€ The surface burner heads are removable.
The cap
"Un"ER"EAO
Burner
Heads
portion of the hcad is porcelain
and the port area
c_g __-.
_
is aluminum.
Wash the burner heads in the sink
__00,
_°"_
with mild detergent
and a plastic scrubber.
Po,t,u,,
A__ntation
tuignl
• Check to be sure all ports are open. To open
_it. p_.,
clogged
ports, insert a straight pin directly into each
__
port. Do not enlarge or distort the port.
Ignitor
• When replacing
the burner heads, carefully
align the
tab on the burner base with the indentation
in the
x_b
head. The two pins will fit in the slots when the tab
is aligned with the indentation.
BURNt=R BA5 I=
NOTE." Wi_en burner heads are removed f!)r cleaning,
do no•spill liquMs through the holes in the
bmvwr
base.
* Brand names are trademarks
of the respective
manufacturers.
Advertisement
Table of Contents
