Adjusting The Oven Temperature - Jenn-Air JER8785QAF Use & Care Manual

÷
÷
Adjusting the Oven Temperature
Oven temperatures are carefully tested for accuracy at the
factory. [t is normal to notice some baking or browning
differences between a new oven and an old one. As ovens
get older, the oven temperature can shift.
You may adjust the oven temperature if you think the oven is
not baking or browning correctly. To decide how much to
change the temperature, set the temperature 25 degrees
higher or lower than your recipe recommends, then bake.
The results of the "test" should give you an idea of how much
to adjust the temperature.
To adjust the oven temperature: Bake
/
1. Press the Bake pad. .......
2. Enter 550° by pressing the appropriate number pads.
3. Press and hold the Bake pad for several seconds or until
O0 ° appears in the display.
[f the oven temperature was previously adjusted, the
change wi[[ be displayed. For example, if the oven tem-
perature was reduced by 15° the display wi[[ show "-15 °''.
4. Press the Autoset 0 pad to adjust the temperature.
Each time the Autoset pad 0 is pressed, the temperature
changes by 5°. The oven temperature can be increased or
decreased by 5° to 35°.
Pressing the Autoset 0 pad wi[[ first cycle through increas-
ing the oven temperature (5, 10.... 35). Continuing to
press the Autoset 0 pad wi[[ then cycle through decreasing
the oven temperature (-35, -30.... -5_).
5. The time of day wi[[ automatically reappear in the display.
You do not need to readjust the oven temperature if there is a
power failure or interruption. Temperature adjustment applies
to Bake, Convect Bake and Convect Roast (select mode:s)
only. Broiling and cleaning temperatures cannot be adjusted.
Changing Temp °F/°C
1. The factory default setting for temperature is Fahrenheit.
2. To change the setting, press and hold the CANCEL and Bake
pads at the same time for three seconds.
3. A single beep wi[[ sound and the current setting wi[[ be
displayed (°F or °C_).Of no change is made, the range wi[[
return to the existing setting after 30 seconds.:)
4. To change the setting, press the Autoset 0 pad. Press again
to return to existing setting. Wait five seconds and the setting
wi[[ be complete.
The Favorite pad allows you to save the time and temperature
from a Cook & Hold function.
To set a Favorite cycle, Cook & Hold must be either active or
just programmed.
To set a new Favorite cycle or to save a enr-
rent[y rnnning Cook & Hold as a Favorite:
1. Program a Cook & Hold cycle as described in the Cook &
Hold section on page 13.
\
2. Press and hold the Favorite pad for three ....
Favorite
seconds.
° The newly set or currently running Cook & Hold cycle
wi[[ be saved.
° A beep wi[[ sound to indicate that the control has
accepted the Favorite setting.
TO start a cycle programmed into Favorite:
1. Press the Favorite pad.
, Time and temperature for the set Cook & Hold cycle wi[[
be displayed. (If no Cook & Hold cycle has been pro-
grammed, "nonE" is displayed.)
2. Press the Bake, Convect Bake or Convect Roast (select
mode:s) pad.
, The Favorite cycle wi[[ begin immediately.
, The selected cycle word wi[[ light in the display
, The cooking time wi[[ light in the display
When the cooking time has elapsed:
, The selected cycle word wi[[ turn off.
, HOLD and WARM wi[[ [ighL
, 170°wi[[ display.
To cancel a Favorite cycle in progress:
1. Press the CANCEL pad. .......
CANCEL
° The stored Favorite cycle wi[[ not .....
be affected.
2. Remove food from the oven.
÷
19
8113 P417-60B 20 _ 9/28/04, 11:40 AM