1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Power Tool
  5. 113.213100
  6. Owner's manual

Craftsman 113.213100 Owner's Manual

Motorized 8-inch bench model drill press
Hide thumbs
Table of Contents

Advertisement

Quick Links

SaveThis
ManuaJ
"_\
For Future Reference
P
MODEL NO.
113.213100
DRILL PRESS WiTH
MAXIMUM
DEVELOPED
1/3 HP MOTOR
Serial
Number
Modet
and
serial number
may
be found
01 the let1`
side of the head,
You should
record
both
model
and
serial number
in
a safe place
for future
use.
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
S_ ARS / £RRFTSMRll®
MOTORIZED
8-INCH
BENCH MODEL DRILL
• assembly
• operating
• repair pads
L... CAREFULLY
..//
SEARS, ROEBUCK AND CO., Hoffman
Estates, IL 60! 79 U.S.A.
Part No, SP5493
Printed in r--h._.,
,._._._,

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 113.213100

Summary of Contents for Craftsman 113.213100

  • Page 1 SaveThis ManuaJ "_\ For Future Reference MODEL NO. 113.213100 DRILL PRESS WiTH MAXIMUM DEVELOPED 1/3 HP MOTOR Serial Number Modet serial number be found 01 the let1` side of the head, S_ ARS / £RRFTSMRll® You should record both model serial number a safe place for future...

  • Page 2: General Safety Instructions For Power Tools

    FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS if within one year from the date of purchase, this Craftsman Dritl Press falls due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERV- ICE CENTER/DEPARTMENT THROUGHOUT THE UNITED STATES.

  • Page 3: Additional Safety Instructions For Drill Presses

    additiona safety instructions for drJ! presses press off and unplug it until the particular part SAFETY SIGNAL WORDS is properly repaired or replaced. DANGER: means if the safety information is not b. Never place your fingers in a position where followed someone will be seriously injured or killed.
  • Page 4 Use only accessories designed for this drill The operation of any power tool can result in for- press to avoid serious injury from thrown bro- eign objects being thrown into the eyes, which can ken parts or work pieces. result in severe eye damage.

  • Page 5: Table Of Contents

    glossary of terms 1. Workpiece 4. Revolutions Per Minute (R.P._I.) The item on which the cutting operations is being The number of turns completed a spinning object performed. in one minute. 2, Drill 5, Spindle Speed The cutting tool used in the drill press to make holes The RPM of the spindle.

  • Page 6: Motor Specifications And Electrical Requirements

    motor specifications and electricam requirements MOTOR SPECiFiCATiONS This power tool is equipped with a 3-conductor cord and grounding type plug, approved by Underwriters' This dri!l press is designed to use a 1725 RPM motor Laboratories. The ground conductor has a green jacket only.

  • Page 7: Unpacking And Checking Contents

    TABLE OF LOOSE PARTS WARNING: To avoid injury from unexpected starting or eaectrica! shock, never connect plug Mtem Description Qty, to out_et until aBlassembay is complete and you Head Asm ......read aH instructions. Column Suppo_,t Asm ....Owner's Manual ...... Model 113.2!3100 Drill Press is shipped complete in Box of Loose Paris...
  • Page 8 List of loose parts in the box and bags M8x1.25-20 Hex Head Screw (3) Support Lock Handle (1) M5x0.8-12 Pan Head Screw (1) Feed Handle (3) M4 Hex "L" Wrench (1) _Chuck Key (1) Belt Guard Knob (1) Chuck (1) Key-Switch (1)

  • Page 9: Location And Function Of Controls

    ocation and function of controWs 1, BELT GUARD .°. Covers Pu!teys and be!t during COLUMN Conp, ects head, table, and base or_ operation of drill press. a one-piece tube for easy alignment and move- me_t. 2, BELT TENSION LOCK. HANDLE,.. Tighteni_g handles locks motor bracket suppo_ to maintain 12.

  • Page 10: Assembly

    assembly WARNING: To avoid injury from unexpected I starting or electrical shock, never connect plug 1 to outlet unti! aH assembly stepsare completed COMBINATgON SQUARE MUST BE TRUE. and you read a!l instructions, Check ifts accuracy as Uiustrated below. TOOLS NEEDED STRAIGHT EDGE...

  • Page 11: Installing The Head

    TABLf_£ SUPPORT TABL_ S U P P O R T ..LOCK HANDLE Locate support lock handle among !oose parts. h-_stail support lock i_and/e from ieft side into table st._pporl, Raise tabie to workin 9 height by siidin 9 it on the columr_ and then tighten iock har_die by...

  • Page 12: Installing Feed Handles

    iNSTALLiNG FEED HANDLES 1. Locate three (3) feed handles among loose parts. 2. Screw the feed handles tightly into the threaded holes in the hub. FEED HANDLE INSTALMNG THE CHUCK 1. Locate the chuck among loose parts. 2. Clean out the TAPERED HOLE in the chuck; clean the spindle nose with a clean cloth.

  • Page 13: Installing Belt Guard Knob

    5mm DIA, × 12ram LONG CROSS RECESS SCREW BELT GUARD KNOB INSTALLING BELT GUARD KNOB 1. To attach belt guard knob, use knob and 5mm Dia. x 12mm long pan hd. screw in loose parts bag. tnstalf screw in hole located in guard and attach knob, turn- ing until tight.

  • Page 14: Adjusting The Table Square To Head

    ADJUSTING TABLE SQUARE HEAD NOTE: The combination square must be "true." See the beginning of the "Assembly" section for a method to check four square. 1. Insert precision round steel rod or straight drill bit approximately 3" long into chuck and tighten. 2.

  • Page 15: Getting To Know Your Drill Press

    9 tt_ng to know your ddli press BELT GUARD FEED HANDLE BELT TENSION LOCI4 HANDLE ON-OFF SWITCH HEAD LOOK S, ET SCREWS FEED SPRING ADJUSTMENT CHUCK FEED TABLE SUPPORT SPRING DEPTH POINTER TABLE . STOP NUTS COLUMN COLUMN SUPPOF:tT SPRING BASE "_ DEPTH...

  • Page 16: Spindle Speeds

    This Drill Press has 3 speeds as listed below: SPINDLE SPEEDS iN R.P.M° 620 RPM 1300 RPM 3100 RPM See inside of belt guard for specific placement of belts on pulleys. Feature Descriptions 1. BELT GUARD... Covers pulleys and belt during 13.

  • Page 17: Onooff Switch

    ONoOFF SW_TCH Insert KEY into switch. NOTE: Key is made of Yellow plastic. To turn drill ON,,. Insert finger under switch lever and puli. To turn drill OFF... Push lever in. In an emergency: If the drill bit BINDS.., STALLS... STOPS...or tends to tear the workpiece loose...you can QUICKLY turn the drill OFF by hitting the switch with the palm of your hand.

  • Page 18: Basic Drill Press Operation

    basic drill press operation -- Securely tock Head to Column, Table Sup.- Follow the following instructions for operating your drill port to Column, and Tabte to Table Support press to get the best results and to minimize the likeUi- before operating dril! press. hood of personal injury.

  • Page 19: Positioning Table And Workpiece

    POSiTiONiNG TABLE AN{} WORKP_ECE Lock the table to the coiumn in a position so that the tip of the drill is just a iittle above the top of the work - piece, A_ways place a piece of BACK-UP t_4ATERtAL (wood. plywood .

  • Page 20: Hole Location

    Before turning the switch ON, bring the drill down to WARNING: To avoid injury from spinning work the workpiece lining it up with the hole location. or tool breakage, always clamp workpiece and FEEDING backup material securely to table before operating drill press with the table tilted.

  • Page 21: Removing The Chuck

    SLEEVE _----_ REMOVING THE CHUCK 1. Open jaws of chuck as wide as they will go by CHUCK L_L( turning chuck sleeve. 2. Carefully tap chuck with mallet in one hand while holding chuck in other hand to prevent dropping it when released from spindle nose.

  • Page 22: Maintenance

    maintenance "Off" and remove plug from power source outlet WARNING: For your own safety, turn switch before maintaining or lubricating your drill press. _wGREEN 8LACK, CONN Frequently blow out any dust that may accumulate in- side the motor. A coat of automotive type paste wax applied to the table and column will help to keep the surfaces clean.

  • Page 23: Trouble Shooting

    trouble shootir g WARNING: For your own safety, turn switch "Off" and always remove plug from power source out_et before troubSe shooting. ® CONSULT YOUR LOCAL SEARS SERVICE CENTER IF FOR ANY REASON MOTOR WILL NOT RUN. REMEDY pROBABLE CAUSE TROUBLE 1.

  • Page 24: Repair Parts

    repair parts rrC_ <...
  • Page 25 repair parts 0oc5 CL L_ ..© © COd) CO0") ©_dO001I COOZZ n 0 _0 © oO oo CO cO %, 5d "E n_ e_ • " ,.z l..U, "-09 o×4 __o_ ooo. ,--'_ C_ 0,.I .r-- >" 000009090000 e000 0000 C00_0Dr...0 o009o0...
  • Page 26 PARTS LiST FOR CRAFTSMAN 8" DRILL PRESS MODEL NO. 113.213100 Always order by Part Number--Not by Key Number FIGURE 2 Part Part Description Description STD315235 817451-1 Bushing-Rubber *Bearing-Ball 17mm 817325 Knob 817408 Spacer 816755-4 Screw-Pan Hal. M5 x 0.8-12...
  • Page 27 PARTS MST FOR CRAFTSMAN 8" DRILL PRESS MODEL NO. 113.213100 11_"_'_ "_" Always order by Part Number--Not by Key Number FIGURE FIGURE 3 QUILL ASSEMBLY Part Part Description Description Gasket-Quill 817773 817413 Support-Table w!Scale 817290 STD315215 * Bearing-Ball 12mm...
  • Page 28 MOTORIZED For the repair or replacement parts you need Call 7 &m - 7 prn, 7 days a week MODEL NO. t oOOOo3G6oPART ] ] 3.213100 (1-880-305-7278) DRILL PRESSWITH MAXIMUM DEVELOPED 1/3 HP MOTOR For in-home major brand repair service Call 24 hours a day, 7 days a week 1-800=4-REPA|R (1-800-473-7247)

Table of Contents