Craftsman 113.213843 Owner's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Power Tool
  5. 113.213843
  6. Owner's manual
Craftsman 113.213843 Owner's Manual

Craftsman 113.213843 Owner's Manual

1/3 hp motor, motorized 13 inch floor model drill press
Hide thumbs
Table of Contents

Advertisement

Quick Links

SAVE THiS MANUAL
FOR FUTURE REFERENCE
MODEL NO.
113.213843
DRILL
PRESS
WITH
1/3 HP MOTOR
Serial
Number
..........................................
Model
and
serial
number
may be found at the rear of
the head,
You
should
record
both
model and serial number
in
a safe place for future use.
CAUTION:
Read
GENERAL
and
ADDITIONAL
SAFETY
INSTRUCTIONS
carefully
®
MOTORIZED
13 iNCH
FLOOR MODEL
.L PRESS
• assembly
• operating
® repair parts
Sold
by
SEARS,
ROEBUCK
AND
CO.,
Chicago,
IL. 60684
U.S.A.
PART
NO
3P4963
PRINTED
iN U.S.A

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 113.213843

Summary of Contents for Craftsman 113.213843

  • Page 1 SAVE THiS MANUAL FOR FUTURE REFERENCE MODEL NO. 113.213843 DRILL PRESS WITH 1/3 HP MOTOR Serial Number .......... ® Model serial number may be found at the rear of the head, MOTORIZED should record both 13 iNCH model and serial number a safe place for future use.

  • Page 2: General Safety Instructions For Power Tools

    FULL ONE YEAR WARRANTY ON CRAFTSMAN DRILL PRESS If within one year from the date of purchase, this Craftsman Drill Press fails due to a defect in material or workmanship, Sears will repair it, free of charge. WARRANTY SERVICE IS AVAILABLE...
  • Page 3 22. NEVER LEAVE TOOL RUNNING UNATTENDED 21. DIRECTION OF FEED Turn power off. Don't leave tool until it comes to a Feed work into a blade or cutter against the direc- tion of rotation of the blade or cutter only. complete stop.

  • Page 4: Table Of Contents

    presses additional safety instructions for drill 13. Think Safety. Safety is a combination of operator c. Do not install or use any drill that exceeds 7"'in common sense and alertness at all times when the length or extends 6" below the chuck jaws. They drill press is being used.
  • Page 5 UNPACKING AND CHECKING ..TOOLS NEEDED CONTENTS Model No. 113.213843 is shipped complete in one car- ton and includes a 1/3 HP 1725 RPM motor. COMBINA_ Separate all parts from packing materials and check each one with the "Table of Loose Parts" to make certain all items are accounted for, before discarding any pack- COMBINATION SQUARE...
  • Page 6 motor specifications and emectricalrequirements MOTOR SPECiFICATiONS This power to01 is equipped with a 3-conductor cord and ground ng type plug which has a grounding prong, ThL_ drill nr_._._ i._ d_.._inn_d to H_. _ 17PR motor -"- " ..° ..... _ '- _""...
  • Page 7 assembmy WARNING: For your own safety, never connect plug to power source outlet until all assembly steps COLUMN are completed. SUPPORT ASSEMBLY OF COLUMN AND TABLE HARDWARE 1. Position base on floor. Remove protective covering and discard. 2. Remove protective sleeve from column tube and discard.
  • Page 8 TABLE LOCK 2. Remove protective covering from table and discard, Place table in table support. Locate one ('1) 3/8-16xl TABLE 1/2 hex head bolt and assemble in table support, Tighten with adjustable wrench. TABLE SUPPORT INSTALLING THE HEAD CAUTION: The head assembly weighs about 55 COLUMN HEAD...
  • Page 9 FLAT SL iNSTALLiNG MOTOR PULLEY 1. Loosen set screw in motor pulley using 1/8" HEX "L" wrench. 2. Slide pulley onto motor shaft. Line up the flat surface on the motor shaft with the set screw in pulley. 3. Make sure the pulley does not rest on the lower guard.
  • Page 10 assembly 7. Locate one (1) V-bett and choose speed for drilling operation, install belt in correct position for desired speed. NOTE: Refer to chart on sideon Drill Press for Recom- mended Drilling Speeds. 8. Apply tension to belt by turning Belt Tension Handle counter clockwise until belt deflects approximately 1/2 inch by thumb pressure at its center.
  • Page 11 MOTOR CONNECTIONS WARNING: For your own safety, never connect pUugto power source outlet until all assembJy steps LACK WIRE TO TERMINAL are completed. COPPER POST 1. Open motor connector box cover located on under- GREEN WIRE side of motor using a flat blade screwdriver. To GREEN soREw WARNING;...
  • Page 12 , ii ,i _" iii ii_ !_i_' i_ _i_ii!i i_i_ i , _ i _ _NSTAEUNG THE CHUCK the TAPERED HOLE in the chuck c can the spindie noSe with a clean cloth. Make sure there nO foreign particles sticking to the surfaces. The €"_ "k, I.__._...
  • Page 13 ADJUSTING THE TABLE SQUARE TO HEAD NOTE: The combination square must be "true". See "Unpacking and Checking Contents" section method. 1. Insert a precision ground steel rod approximately 3" long into chuck and tighten. 2. With table raised to working height and locked on column, place combination square flat on table be- side rod.

  • Page 14: Getting To Know Your Drill Press

    getting to know your drill press DEPTH., SCALE DRILL "ON-OFF" BELT GUARD FEED SPRING SWITCH DEPTH POINTER ADJUSTMENT BELT TENSION SPRING FEED BELT TENSION LOCK HANDLE CHUCK LOCKING I Ii"_L_,_.Lj.,.--.,-._.. ,_uuu COLLAR Q_"-_ HEADLOCK SPRING COLUMN COLLAR FEED HAN DLE RACK TABLE BEVEL LOCI_...

  • Page 15: Depth Scale

    ® ® SPINDLE SPEEDS iN R.P.M. ThisDrillPresshas5 speeds as listedbelow: 400RPM ----- 12OO 800RPM 1200RPM 1800RPM 2800RPM Seerightsideof Headforspecific placement ofbelts on pulleys. 1. BELT GUARD ASSEMBLY . o . Covers pulleys BEVEL SCALE . .. Shows degree table is tilted and belt during operation of drill press.
  • Page 16 i i i ii i i:iiiii ii ii!ii!i!iii!i iii! iiiii! !iiii i ii ?i iiii iiii ii!i ii iiiiiiiiii i !i, i!ii i iiii/ ;!:ii!iii_iiiiii!i;_i_i_i_i_i_i! _i_ ;;_iiii ? i:_iiiiii_i!!_!_ j!i;_i!ii!_ _i:iii;i_ii_i_i ;iii!i_iiiii!!!ii_ i_i i _iii _ i I i_ii i i 2&...

  • Page 17: Tensioning Belt

    CHUCK KEY... It is a self-ejecting chuck key which DRILLmNG SPEED... Can be changed by placing the will "pop" out of the chuck when you let go of it. This belt in any of the STEPS (grooves) in the pulleys. See action is designed to help prevent throwing of the chuck Spindle Speed chart on right side of Head.

  • Page 18: Installing Drills

    _ .._ i_, • _ii_ii_i_ii_iii! _ '_ _i __ Follow the following instruCtions for operating your drill Never perform operation "FREE- pressto get the b_st results andto minirnizethelikeii! HAND (hand,holding workpiece rather hood pf pers0naiinjury: than supporting it on the table), except WARNING: For your own safety, always observe when polishing.

  • Page 19: Positioning Table And Workpiece

    POSiTiONING TABLE AND WORKPIECE Lock the table to the column in a position so that the tip of the drill is just a little above the top of the work- piece. Always place a piece of BACK-UP MATERIAL (wood, plywood...) on the table underneath the workpiece.

  • Page 20: Hole Location

    basic drill press operat on WARNING: To avoid injury from spinning work or Before turning the switch ON, bring the drill down to tool b{eakage, always clamp, workpiece and back- the workpiece lining it up with the hole location. up material securely to table before operating Drill Pl'ess with the table tilted, FIEEDiNG To return table to original position: loosen set screw...

  • Page 21: Maintenance

    maintenance WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before maintaining or lubricating your drill press. Frequently blow out any dust that may accumulate in- side the motor. A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.

  • Page 22: Basic Drill Press Operation

    WARNING: For your own safety_ turn sw_tch "OFF" and always remove plug from power source outlet before troubie shooting, e CONSULT YOUR LOCAL SEARS SERVICE CENTER tF FOR ANY REASON MOTOR WILL NOT RUN. REMEDY TROUBLE PROBABLE CAUSE 1, Incorrect beit tension. 1.
  • Page 24 PARTS LIST FOR CRAFTSMAN 13" DRILL PRESS MODEL NO. 113.213843 PO,VC_CoRO WIRING DIAGRAM ... 11'= FIG. 4 FIGURE 2 • Any attempt to repair this motor may create a HAZARD unless repair is done by a qualified service technician. Repair service is available at your nearest Sears Store.

  • Page 25: Clamp, Bolt

    PARTS LiST FOR CRAFTSMAN 13" DRILL PRESS MODEL NO. 1!3.213843 FIGURE 2 ALWAYS ORDER BY PART NO. - NOT BY KEY NO. Part Part Description Description 605O4 Belt"V" 3/8x42 STD 541037 *Nut, Hex3/8-16 71361 71375 Pulley, Motor Spring, Torsion STD 502503 71317 *Screw, Soc.
  • Page 26 PARTS LiST FOR CRAFTSMAN 13" DRILL PRESS MODEL NO. 113o213843 FIGURE 4 ALWAYS ORDER BY PART NO. - NOT BY KEY NUMBER No. , Description 60509 Ring, Retaining 21/32 STD 315235 *Bearing, Ball 17MM 71384 Tube, Quill 60503 Bearing, Thrust...
  • Page 27 NOTES:...

  • Page 28: Repair Parts

    MOTORIZED 13 iNCH FLOOR MODEL DRILL, PRESS Now that you have purchased your 13 inch drill press should a need ever exist for repair parts or service, simply contact any Sears Service SERVMCE Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit.

Table of Contents