Hoover FloorMate SpinScrub Hard Floor Cleaner Manual
Hard floor cleaner with portable tool kit
Hide thumbs
Also See for FloorMate SpinScrub Hard Floor Cleaner:
- Owner's manual (20 pages) ,
- Owner's manual (32 pages)
Related Manuals for Hoover FloorMate SpinScrub Hard Floor Cleaner
Summary of Contents for Hoover FloorMate SpinScrub Hard Floor Cleaner
- Page 1 HOOVER -ENGL/SH -_ pp. 1-20 ESPANOL -_ pag. 21-36 FloorMate SpinScrub Hard Floor Cleaner with portable tool kit www.hoover.com...
- Page 2 Do not run appliance over water, take it to a Hoover Sales cord. Keep cord away from heated Service Center or Authorized mrfaces. Hoover Warranty Service Dealer.
- Page 3 Warranty ....Parts & accessories mail order form ..... Hard floor cleaner Nozzle Upper handle Brush assembly Tool caddy Floor swivel tool Telescoping wand Hose Floor cleaning concentrates 00,s <;) _ZZ} LISTED © 2004 The Hoover Company www.hoover.com Continued...
- Page 4 This cleaner is intended for house- hold use. Operate cleaner only at voltage speci- fied on data plate on back of cleaner. Plug cleaner into a properly grounded outlet. "5 This user manual applies to models with either 6 or 7 brushes. Soft hand grip...
- Page 5 Rotate bottom handle support (A) up the upright position until a snap felt. Align control rod (B) on upper handle (C) with slot in bottom support (D). Push upper handle (C) all the way down until you hear it snap place.
- Page 6 Press brush assembly firmly to snap into place. To install nozzle, make sure latches (C) are out. For easier installation, place cleaner in upright position. Align middle section (D) of nozzle with opening (E) on cleaner. Remove cardboard packing insert from squeegee area on underside of nozzle.
- Page 7 Store hose; tools and accessories To store hose: Place the hose grip (A) into (B) on back of caddy Pull hose up and press into cut-out area (C). Continue wrap- ping hose down, underneath tongue (D), and back pressing into second cut-out area...
- Page 8 (A) on the front of the cleaner. Your HOOVER FloorMate SpinScrub Cleaner can be used to both vacuum debris clean non-carpeted floor surfaces such as vinyl,...
- Page 9 (2 oz.) HOOVER® Floor to Floor Cleaner. Check for worn spots or joint separations before using, as these conditions could lead to damaged flooring when using water to clean floor.
- Page 10 If rubber ring (D) on cap has become dislodged, reposi- with uneven side against ledge (E) as shown. Replace cap. Rotate cap clockwise until it locks in place. must be locked in place for proper performance and to prevent leaking. Slide tank straight into position until latch snaps in place.
-
Page 11: Solution Tank
to empty Turn cleaner off and disconnect from electrical outlet. Although necessary for satisfactory performance, is recommended that the recovery tank be emptied after dry vacuuming before operation. Check the solution tank also. It may need to be refilled at this time. - Page 12 Use your HOOVER® FloorMate SpinScrub Cleaner • Dry Vacuum to remove loose dirt, hair and debris. • Wet Clean the floor surface. The brushes will provide light agitation to help loosen dirt.
-
Page 13: Picking Up Spills
NOTE: Your HOOVERCR) FloorMate SpinScrub cleaner may be used to clean wood floors that have been sealed with a polyurethane coating and can be cleaned with water. CAUTION: To prevent damage to wood floors, follow the flooring manufacturer's cleaning rec- ommendations. - Page 14 Floor swivel tool • Swivel head • 2 rows of brushes • Use to clean small, tight areas Attach hose tool Unplug cleaner from electrical outlet. to connect hose _/Open hose door (A) on side of cleaner. _/Align hose connector (B) with hose solution...
-
Page 15: Storage
• Do not store cleaner on a wood surface unless cleaner completely dry. For your convenience, the HOOVER(_ FloorMate pinScrub tool caddy (A) is provided for storing hose, tool, telescoping wand, set of brushes detergent. caddy... - Page 16 Cleaning the nozzle Turn cleaner disconnect from electrical outlet. The cleaner's nozzle be removed for easy cleaning. Slide the two nozzle release latches (A) outward. Remove nozzle (B) by pulling straight out. Rinse nozzle under running water. Remove debris from squeegee (C) and wipe with a damp cloth.
-
Page 17: Cleaning The Brushes
Cleaning the brushes The brush assembly be removed for easy cleaning. Turn cleaner disconnect from electrical outlet. Place handle in the upright position. Remove tanks to prevent leaking. Set aside. Pull the two nozzle release buttons (A) out. Remove nozzle. Tilt cleaner back so handle... - Page 18 Use the list below to help solve minor problems. Cleaner won't ,/Make sure the cleaner plugged in firmly. ,/Check the fuse or breaker. Low suction ,/Empty the recovery tank; it may be full the automatic shut-off engaged. ,/Make sure filter filter lid are properly positioned.
-
Page 19: Service
Do not lubricant to motor bearings. To obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer (Depot) by: ¢' Checking the Service Section of Hoover... - Page 20 Full One Year Warranty (Domestic Use) Your HOOVER@ appliance is war- ranted in normal household use, in accordance with the Owner's Manual against original deDcts in material and workmanship fbr a period of one filll year fi'om date of purchase.