Advertisement
B.
Never use grinding
wheels, abrasive cut-off
wheels,
friction
wheels (metal slitting blades) wire wheels or
buffing wheels.
11. USE ONLY
ACCESSORIES
DESIGNED
FOR THIS
SAW,
12. Cross-cutting operations are more conveniently worked
and with greater safety if an auxiliary wood facing is
attached to the miter gauge using the holes provided,
13. Make sure the top of the arbor or cutting tool rotates
toward
you
when
standing in norm_
operating
position.
Also make sure the cutting tool, arbor collars
and arbor nut are installed properly.
Keep the cutting
tool
as low
as possible for
the operation
being
performed.
Keep all guards in place whenever _ossible.
14. Do not use any blade or other cutting tool marked for
an operating speed less than 3450 RPM. Never use a
cutting tool larger in diameter than the diameter for
which the saw was designed. For greatest safety and
efficiency
when ripping, use the maximum diameter
blade for whicl_ the saw is designed, since under these
conditions the spreader is nearest the blade.
15. Adjust table inserts flush with the table top. NEVER
operate the saw unlessthe proper insert is installed.
16. THINK SAFETY.
Safety is a combination of operator common sense and
alertness at all times when the saw is being used.
17. NOTE
AND
FOLLOW
SAFETY
INSTRUCTIONS
THAT APPEAR ON THE FRONT OF YOUR SAW.
DANGER
FOR YOUR OWN SAFETY
READ AND UNDE RSTAND OWNER'S MANUAL
BE FORE OPERATING
MACHINE:
I.
WEAR SAFETY GOGGLES
2,
USE SAW-BLADE GUARD
FOR "THRU-SAWING"
3.
KEEP HANDS OUT OF PATH OF SAWBLADE
4.
USE A"PUSH-STICK"
WHEN REQUIRED
5.
KNOW HOW TO AVOID
"'KICKBACKS'"
6.
DO NOT PERFORM OPERATIONS
"FREEHAND"
18. WARNING:
DO
NOT
ALLOW
FAMILIARITY
(GAINED
FROM
FREQUENT
USE OF YOUR SAW)
TO
BECOME
COMMONPLACE.
- ALWAYS
REMEMBER
THAT
A CARELESS
FRACTION
OF A
SECOND
IS SUFFICIENT
TO
INFLICT
SEVERE
INJURY.
19. WARNING:
THE
2-1/2"
SAW PULLEY
AND THE
2-1/2"
MOTOR
PULLEY
FURNISHED,
WILL
RUN
THE
BLADE
AT
APPROXIMATELY
3450
RPM
WHEN
USED WITH
A 3450 RPM MOTOR.
NEVER
SUBSTITUTE
THESE PULLEYS TO INCREASE
THIS
SPEED BECAUSE IT COULD BE DANGEROUS.
The operation of any power tool can result in foreign
objects being thrown into the eyes, which can result in
severe eye damage. Always wear safety gogglescomplying
with ANSI Z87.1 (shown on Package) before commencing
power tool operation. Safety Goggles are available at Sears
retail or catalog stores.
MOTOR SPECIFICATIONS
AND
ELECTRICAL
REQUIREMENTS
This saw is designed to use a 3450 RPM motor only. Do not
use any motor that runs faster than '3450 RPM, It is wired
for operation on 110-120 volts, 50 Hz., alternating current.
IT MUST NOT BE CONVERTED
TO OPERATE
ON 230
VOLTS.
EVEN
THOUGH
SOME
OF
THE
RECOMMENDED
MOTORS ARE DUAL VOLTAGE.
The outlet
in the switch box will accept either a 15 amp. or
a 20 amp. motor plug.
RECOMMENDED
CRAFTSMAN
MOTORS FOR USE ON
THIS SAW.
No.
H.P.
R.P.M.
Volts
Catalog
1
3450
110.120
1217
1
3450
110.120
1220
If power
cord is worn
or cut, or damaged
in any way, have
it replaced
immediately.
If your
saw is for
use on less than
150 volts
it has a plug
that looks
like below.
6
3-PRONG PLUG
GROUNDING
PRONG
PROPERLY
GROUNDED
3-PRONG
OUTLET
See recommendation
on saw for use in Canada
CAUTION:
Do not use blower or washing machine motors
or any motor with an automatic reset overload protector as
their use may be hazardous.
CONNECTING
TO POWER SOURCE OUTLET
This saw must be grounded while
in use to protect
the
operator from electrical shock.
Plug power cord into 110-120V properly
grounded type
outlet
protected
by a 15-amp. time delay or Circuit-Saver
fuse or circuit breaker.
IF YOU
ARE
NOT SURE
THAT
YOUR
OUTLET
IS
PROPERLY
GROUNDED,
HAVE
IT CHECKED
BY A
OUALI FlED ELECTRICIAN.
WARNING:
DO NOT PERMIT
FINGERS
TO TOUCH
THE TERMINALS
OF PLUG WHEN
INSTALLING
OR
REMOVI_IG
THE PLUG TO OR FROM THE OUTLET.
Advertisement
