Advertisement
Quick Links
Future Reference
MODEL NO.
1!3.23($180
SCROLL SAW
Variable Speed
Serial
Number
Model and ser;al number may be found
attached to the underside of the work-
table.
You
should
record
both
model
and
serial numberin
a safeplace
for future
use.
FOR YOUR
SAFETY:
READ ALL
INSTRUCTIONS
carefully.
16" VARIABLE
ELECTRONIC
SCROLL SA
• assembly
• operating
o repair parts
, ....
_
_
___=__
....
Sotd by SEARS,
ROEBUCK
AND CO., Chicago,
ILo 60584 U.S.A.
Par11'qo.SP5367
Advertisement
Related Manuals for Sears Craftsman 113.236180
Summary of Contents for Sears Craftsman 113.236180
- Page 1 Future Reference MODEL NO. 1!3.23($180 SCROLL SAW Variable Speed Serial Number Model and ser;al number may be found attached to the underside of the work- table. should record both model serial numberin a safeplace for future 16" VARIABLE use. ELECTRONIC SCROLL SA FOR YOUR SAFETY:...
- Page 2 material or workmanship, Searswillrepair WARRANTY'SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE CENTER!DEPARTMENT THROUGHOUT THE UN TED STATES Thiswarranty applies only while this product is used in the United States, This warranty gives you specific legal rights and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., DEPT.
- Page 3 ,i,i i1,1 USE RECOMMENDED ACCESSORIES ensure that itwill operate properly and perform its Consult the owner's manual for recommended intended function. Check for alignment of mov- accessories. Follow the instructionsthat accom- ing parts, binding of moving parts, breakage of parts, mounting, and any other conditions that pany the accessories.
- Page 4 or su 8, Should any part of this scroll saw bt fail in any way, or any perform properly, shut off and remove plug from power supply outlet. Replace damaged, missing, and/or failed parts before resuming opera- tion. 9. Think Safety. Safety is a combination of operator common sense FOR YOUR OWN SAFETY: and alertness wheneverthe...
- Page 5 _._.___.._._l_ iml! lU nl ii nll IIH'I_-- _.-_-J _HJlJ ,,,,,,,r It is recommended that you have a qualified electrician a. MOTOR IS OVERLOADED - Overloading occur if you feed too rapidly. replace the two prong outlet with a properly grounded three prong outlet.
- Page 6 contents Warranty information ..;: ..:.._ ..:..i," ,"_12 General Safety Instructions for Power Tools ..2 Additlonal Safety Instruction for Scrol| Saws ..3 Electrical Information ...,..,..,.., ... ;.i....4 Glossary of Terms for Woodworking ....5 Unpacking &...
- Page 7 LIFT FRAME THIS {LIFT HERE) BLADE HOLBER BLADE BEVEL BEVEL LOCK (LIFT HERE) WARNING: FOR YOUR OWN SAFETY, NEVER 1. Lift the saw by the frame and base and place scroll CONNECT PLUG TO POWER SOURCE OUTLET saw on work bench. UNTIL ALL ASSEMBLY STEPS ARE COMPLETE, AND YOU HAVE READ AND UNDERSTAND...
- Page 8 NDICATOR and rnove the table r or at aright blade. BEVEL LOCK KNOB 3; Remove blade support and hold down by loosening the screw in the front of the blade support with a hex "L"wrench. LOOSEN SCREW BLADE SUPPORT AND HOLD DOWN CHECK SPACE...
- Page 9 6. Loosen the screw holding the bevel scale pointer and adjust pointer to 0 degrees. Tighten screw. Remember, the bevel scale is a convenient guide, but should not be relied upon for precision. BEVEL SCALE POINTER SCREW Reassemble the blade support and hold down. Make trial cuts in scrap wood to determine if your angle settings are correct.
- Page 10 i ng binaries removing and nst TENSION KNOB "'U'SHAPED 1. Unplug power cord from outlet. 2. Loosen tension on blade by turning tension knob counterclockwise about four full turns. Loosen the hex screw of blade holder and push it toward left di- rection.
- Page 11 i1,,, BLADE HOLID*OOWN FOOT ADJf3ST[_G KNOB Adjust the blade support by loosening the screw on the top of blade support with a hex "L wrench, and tighten the screw after adjusting. Adjust the blade holder to the table by loosening the _ HOLD-DOWN FOOT lockknob.
- Page 12 BLADE HOLDER 2 HOLD i BLADE BEVE BLADE BEVEL BEVEL LOCK KNOB SPEED CONTROL KNOB ON/OFF KNOB 5. BEVEL SCALE - Shows degree btade is tilted for 1,TENSION KNOB - Tighte ningthe knob (clockwise) will bevel cutting. _ncrease the tension on the blade. Loosening it (counterclockwise) wilt decrease the tension, 6 SPEED CONTROL / ON - OFF KNOB - For speed...
- Page 13 2. To turn machine OFF, control knob is pushed down. NEVER LEAVE THE MACHINE UNATTENDED UNTIL IT HAS COME TO A COMPLETE STOP. The variable speed control may be adjusted to the approximate speeds identified on the control panel. Suggested speeds are identified below. Turn the control knob clockwise ( ) to increase strokes...
- Page 14 to iollow the wood grain as you your scroll • !. The saw does not cut wood by itself. You alJow the intended to cut wood or or material saw to cut wood by guiding the wood into the blade as similar to wood only: it moves, 10, When choosing a blade to use with your scroll saw,...
- Page 15 J l[ Jlill _::__ ....MOUNTING AN AUXILIARy WORK TABLE 1. Four holes are provided in the work table so you can 4 FLAT HEAD easily attach an auxiliary work surface to the saw if SCREWS COUNTERSINK THE AREA AROUND your needs require.
- Page 16 i!!ili ii!iiiii!iiiiii!iii!ili!iii! GENERAL An occasional coat of paste wax on the work table wilt allow the wood being cut to glide smoothly across work surface. MOTOR if the power cord is worn, cut or damaged in any way, METHOD OF OILING BEARINGS have it replaced immediately.
- Page 17 ......_z:_i_ ¸' nl,,i !nlll troubUeshooting WARNING: FOR YOUR OWN SAFETY, PUSH CONTROL KNOB "OFF" AND REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE TROUBLSHOOTING YOUR SCROLL SAW. PROBLEM PROBABLE CAUSE REMEDY SUGGESTED Adjust blade tension. 1. Wrong tension. Breaking blades. Reduce feed rate.
- Page 18 • i ¸...
- Page 19 !6 tNGH SCROLL VARIABLE SPEED ELECTRONIC SERVtCE Now that you have purchased your Scroll Saw, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you call or visit.