Left Margin; Right Margin; Top Margin; Bottom Margin - Epson MTX 1345 Operator's Manual

- Vertical Positioning Adjustment (VERT.POS.ADJ.)
This function changes the vertical position in the current macro for the five
different paper paths TRACTOR V-POS ,MANUAL V-POS or BIN x V-POS
(x = 1 up to 3) exactly position the printout in relation to the top edge of the
form in use. It is meant to be a corrective parameter to meet variations in
paper size and pre-printed material. Using this function, the TOP MARGIN
and BOTTOM MARGIN setting are taken into account as well.
15
This parameter covers a range of - / to +
the page and "+" is further down the page.
The following table shows some values in inch and millimetres.
1
+/- 1 = +/- / " = +/- 0,42 mm
60
2
+/- 2 = +/- / " = +/- 0,85 mm
60
3
+/- 3 = +/- / " = +/- 1,27 mm
60
4
+/- 4 = +/- / " = +/- 1,69 mm
60
5
+/- 5 = +/- / " = +/- 2,12 mm
60
6
+/- 6 = +/- / " = +/- 2,54 mm
60
7
+/- 7 = +/- / " = +/- 2,96 mm
60
8
+/- 8 = +/- / " = +/- 3,39 mm
60
The set up of VERT.POS.ADJ. will become effective at the next page
Attention:
of the form. Therefore, it is recommended to perform
VERT.POS.ADJ. set up as long as the paper is in the park position
and before starting the print job.
1
- The left margin is set in / " steps, depending on the actual selection. The
10
1
first left margin position is / " from the left edge of the paper which means
20
that the letter H in regular "Data" font would be positioned / " from the left
edge of the paper. The left margin can be set to a maximum of / ".
Configuring the printer
240
/ of an inch, where "-" is up
60 60
9
+/- 9 = +/- / " = +/- 3,81 mm
60
10
+/- 10 = +/- / " = +/- 4,23 mm
60
11
+/- 11 = +/- / " = +/- 4,66 mm
60
12
+/- 12 = +/- / " = +/- 5,08 mm
60
13
+/- 13 = +/- / " = +/- 5,50 mm
60
14
+/- 14 = +/- / " = +/- 5,93 mm
60
15
+/- 15 = +/- / " = +/- 6,35 mm
60
16
+ 16 = + / " = + 6,77 mm
60
1
20
15
10
Configuring the printer
- The right margin is set to print position 80, 132 or 136, always measured
from the position of the first possible, not actual, left margin setting.
The left margin setting is influenced by the physical setting of the left tractor.
The above specifications are only correct if the tractors are in the original
positions, i.e. the left perforation is aligned with the centre mark on the plastic
plate (distance between the marks is / ").
- The top margin indicates the first print line and is always set in steps of / ".
The position of the first margin is / " from the top of the paper and indicates
the baseline of the letter H in upright "Data" font (see illustration).
The top margin can be set to a maximum of / " down on the paper.

Top Margin

Bottom Margin

3-9 3-10
1
10
1
6
16
6

Left Margin

Right Margin

8
1
6