Sony STR-V333ES Operating Instructions Manual page 22

Multi Channel Surround Setup
o
o
5'
c
"a
¢D
5'
c
"a
¢D
"o
¢D
,1 I
¢D
3
• Front speaker crossover frequency
(FRONT SP >)
Initial setting : ST[) (=120 Hz)
Lets you adjust the fi'ont speaker bass crossover frequency
when tile ti'ont speakers are set to "SMALL". Tile
fi'equency call be adjusted in 10 Hz steps ti'om 40 Hz to
200 Hz.
• Center speaker crossover frequency
(CENTER SP >)
Initial setting : ST[) (-120 Hz)
Lets you to adjust tile center speaker bass crossover
fi'equency when tile center speaker is set to "SMALL".
The frequency can be adjusted in 10 Hz steps fi'om 40 Hz
to 200 Hz.
• Rear L/R speaker crossover frequency
(REAR L/R SP >)
Initial setting : ST[) (-120 Hz)
Lets you adjust tile rear L/R speaker bass crossover
ti'equency when the rear L/R speakers are set to
"SMALL". Tile fi'equency call be adjusted in 10 Hz steps
fi'om 40 Hz to 200 Hz.
• LFE high cut filter (LFE HIGH CUT)
Initial setting: STD (-120 Hz)
This setting lets you select the cutoff frequency of the LFE
channel High Cut Filter. Normally, this shoukt set to STD.
The fi'equency can be adjusted in 10 Hz steps fi'om 40 Hz
to 200 Hz. When using a passive subwoofer powered by a
separate power amplifim; it may be better to change the
cutoff freqt_ency. When this is tile case, use a setting other
than STD.
• Distance unit (DIST. UNIT)
Initial setting : fbet (meter)
Lets you select either tbet or meters as tile trait of measure
for setting distances. 1 foot corresponds to a 1 ms
difference.
Use the remote while seated in your listening position to
adjust tile volume of each speaker.
Note
Tbis trait incorporates a new test tone witb a frequency centered
at 800 Hz for easier speaker volume adjustment.
1 Press I/_ to turn on the receiver.
2 Press TEST TONE on the supplied remote.
You will hear tile test tone from each speaker in
sequence.
Adjust
the volume level so that the volume of the
test tone from each
speaker
sounds the same
when you are in your main
listening position.
• To adjust the balance of the fi'ont right and fi'ont left
speakers, use tile front balance paraineter in the
LEVEL menu (see page 38).
• To adjust the balance of the rear right and rear left
speakers, use tile rear balance paraineter in the
LEVEL inenu (see page 38).
• To adjust tile wflume level of the center speaken
press the LEVEL CENTER +/ buttons on the
remote.
• To adjust the wflume level of the mar L/R speakers,
press the LEVEL REAR +/ buttons on tile remote.
• To adjust the wflume level of the rear center speaker,
use tile rear center level parameter ill tile LEVEL
menu (see page 38).
• To adjust the voluine level of the sub woofer, use the
sub woofi_r level paraineter in the LEVEL menu (see
page 38).
4 Press TEST TONE again to turn off the test tone.
Note
Tbe test tone cannot be output wben the receiver is set to 5.1CH
INPI,TT.
"_"aYou can adjust the volume level of all speakers at the same
time
Rotate MASTER VOLUME on the main unit or press MASTER
VOLUME +/ on the remote.
Notes
• The fl'ont balance, rear L/R balance, center level, rear L/R
level, rear center level, and sub wooDr level are shown in the
display during adjustment.
• Although these adjustments can also be made via the front
panel using the LEVEL menu (when the test tone is output, the
receiver switches to the LEVEL menu automatically), we
recommend you fi)lloxt,' t he procedtnv described above and
adjust the speaker levels fl'om your listening position using the
remote control.
22