Unpacking And Checking Contents; Tools Needed; Suppliedloosein Carton; Blade Guard And Spreader - Craftsman 113.290650 Owner's Manual

UNPACKING AND CHECKING CONTENTS
TOOLS NEEDED
.. Medium Screwdriver
(_ Hammer Small Screwdriver
#2 Phillips Type
Pliers _'- Screwdriver
@
Wrenches
1/2 in, 9/16 in.
Combination Square 3/4 in.
Model 113.290600 Table Saw is shipped complete in
one carton with motor but DOES NOT INCLUDE
Table Extensions or Steel Legs.
Model 113.290650 Table Saw is shipped complete in
one carton and INCLUDES Motor, Two Table
Extensions and Steel Legs.
Separate all parts from packing materials and check
each one with the illustration and the list of Loose
Parts to make certain all items are accounted for
before discarding any packing material.
If any parts are missing, do not attempt to assemble
the table saw, plug in the power cord or turn the
switch on until the missing parts are obtained and
are installed correctly.
Remove the protective oil that is applied to the table
top and edges of the table. Use any ordinary
household type grease and spot remover.
CAUTION: Never use gasoline, naptha or similar
highly volatile solvents.
Apply a coat of automobile wax to the table.
Wipe all parts thoroughly with a clean, dry cloth.
WARNING: FOR YOUR OWN SAFETY, NEVER
CONNECT PLUG TO POWER SOURCE OUTLET
UNTIL ALL ASSEMBLY STEPS ARE COMPLETE,
AND YOU READ AND UNDERSTAND THE
SAFETY AND OPERATIONAL INSTRUCTIONS.
P Q
T
COMBINATION SQUARE MUST BE TRUE.
STRAIGHT EDGE OF BOARD
3/4" THICK. THIS EDGE MUST
CRAW LIGHT LINE ON BE PERFECTLY STRAIGHT.
BOARO ALONG THIS EDGE. _'\
SHOULD BE NO GAP OR OVERLAP
HERE WHEN SQUARE IS FLIPPED
OVER IN DOTTED POSITION.
MODEL113.290600
SUPPLIED LOOSEIN CARTON
Item Part Name Qty.
A Blade Guard and Spreader .............. 1
B Rip Fence ............................. 1
C Miter Gauge .......................... 1
D Rip Fence Guide Bar Rod ............... 1
E Rip Fence Guide Bar with Rip Scale (Front) 1
F Rip Fence Guide Bar (Rear) ............. 1
G Motor Base ........................... 1
H Bag Containing ........................ 1
Owner's Manual ....................... 1
Calibration Gauge ...................... 1
Owner's Information Card .............. 1
J Guard, Belt ........................... 1
K Clip, "S" . ............................. 3
L Screw, Pan Hd. Type "T" 10-32 x 1/2 .... 3
M Support, Belt Guard .................... 1
N Bracket Support ........................ 1
Loose Parts Bag No. 62844
(Containing the Following Items):
0 Key, Switch ........................... 1
Loose Parts Bag No. 62836 ............. 1
Loose Parts Bag No. 62836
(Containing the Following Items):
P Rod Assembly, Spreader ............... 1
Q Support, Spreader ..................... 1
R Pulley ................................ 1
S Belt, "V" 1/2 x 41 ...................... 1
T Wrench, Arbor . ....................... 1
U Support, Guard ........................ 1
Loose Parts Bag No. 62835 ............. 1
MODEL113.290600 and !13.290650
Item PartName Qty.
LooseParts Bag. No 62835
(Containing the Following Items):
V Bolt, Carriage 5/16-18 x 3/4 ............ 4
W Nut, Hex 5/16-18 ...................... 8
W Nut, Hex 1/4-20 ....................... 2
X Lockwasher,External5/16 ............. 10
X Lockwasher,External1/4. ............. 2
Y Screw, Hex Hd 5/16-18 x 5/8 ........... 3
Y Screw, Hex Hd. 5/16-18 x 1 ............. 4
Y Screw, Hex Hd. 5/16-18 x 1-3/4 ......... 2
Y Screw, Hex Hd. 1/4-20 x 5/8 ............ 2