Gas Conversion Kits - Superior SLBV-35 Installation Instructions Manual

GAS CONVERSION KITS

This conversion kit shall be installed by a qualified service agency in
accordance with the manufacturer's instructions and all applicable codes
and requirements of the authority having jurisdiction. If the information in
these instruction is not followed exactly, a fire, explosion or production of
carbon monoxide may result causing property damage, personal injury
or loss of life. The qualified service agency is responsible for the proper
installation of this kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified in the manu-
facturer's instructions supplied with the kit.The qualified service agency
performing this installation assumes responsibility for this conversion.
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l'autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d'incendie, d'explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l'installation de cette trousse. L'installation n'est
pas adéquate ni complète tant que le bon fonctionnement de l'appareil
converti n'a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
In Canada:
THE CONVERSION SHALL BE CARRIEd
OUT IN ACCORdANCE WITH THE
REqUIREMENTS Of THE PROVINCIAL
AUTHORITIES HAVING JURISdICTION
ANd IN ACCORdANCE WITH THE
REqUIREMENTS Of THE CAN/
CSA-B149.1 INSTALLATION COdE.
LA CONVERSION dEVRA êTRE
EffECTUéE CONfORMéMENT
AUX RECOMMANdATIONS dES
AUTORITéS PROVINCIALES AYANT
JURIdICTION ET CONfORMéMENT
AUX EXIGENCES dU COdE
d'INSTALLATION CAN/CSA-B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
SUPERIOR B-VENT GAS FIREPLACES • MODELS SLBV-35, SLBV-40 • INSTALLATION INSTRUCTIONS
®
WARNING
AVERTISSEMENT
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure. Refer
to the instructions provided with the conversion
kit when performing any gas conversion.
Natural Gas To Propane Gas
Models
SLBV-35
SLBV-40
Propane Gas to Natural Gas
Models
SLBV-35
SLBV-40
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Millivolt SIT Systems
Conversion Kits
Catalog No.
H8270
H7673
Millivolt SIT Systems
Conversion Kits
Catalog No.
H8271
H7675
Electronic dEXEN Systems
Natural Gas To Propane Gas
Conversion Kits
Models Catalog No.
SLBV-35
SLBV-40
Electronic dEXEN Systems
Propane Gas To Natural Gas
Conversion Kits
Models Catalog No.
SLBV-35
SLBV-40
Gas Conversion Kit Installation
Instructions
Step 1. TURN Off THE GAS SUPPLY TO THE
APPLIANCE and disconnect power
supply at the circuit breaker. Ensure
appliance is cold.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT Off PRIOR TO dISCONNECTING THE
ELECTRICAL POWER, BEfORE PROCEEd-
ING WITH THE CONVERSION.
ATTENTION: AVANT d'EffECTUER
LA CONVERSION, COUPEz d'ABORd
L'ALIMENTATION EN GAz, ENSUITE,
COUPEz L'ALIMENTATION éLECTRIqUE.
Step 2. Remove the front glass enclosure
panel. See Figure 25 on Page 20.
Step 3. Carefully remove the logs.
Note: Logs are fragile. Handle gently
to prevent breakage.
Step 4. Refer to Figure 31. Remove the burner
assembly with attached venturi tube.
for Millivolt Systems, continue to Step 5.
for Electronic Systems, skip to Step 8.
Step 5. SIT Millivolt Valve: Refer to Figure 32
and the instructions provided with the
kit.
a. Using a Torx T20 (with 1/4" shank
and center hole), remove and dis-
card the three pressure regulator
mounting screws.
b. Remove the pressure regulator,
spring, poppet, diaphragm and
bushing.
c. discard all removed components.
d. Make sure the rubber gasket in-
stalled on the back of the replace-
ment pressure regulator is properly
positioned. Tighten screws to 25
in.-lb. torque.
H8268
H7669
H8269
H7671
25