Table of Contents
Advertisement
Four-Way
Chute
Control
TM
This four-way control lever is meant to control the
direction and distance of snow discharge from the
chute. Press the button on the knob and turn it left or
right to rotate the chute to the direction that snow will be
thrown. Tilt the lever forward to decrease the distance
snow will be thrown, and backwards to increase
distance.
Shift Lever
The shift lever is located in the center
' 6
of the handle panel and is used to
_
determine ground speed and direction
4
of travel. It can be moved into any of
3
eight positions.
2
IMPORTANT:
Always release drive
_
r_
control before changing speeds.
Forward: Your snow thrower has six
IR_.-
forward (F) speeds, with position
number one (1) being the slowest
fR2.-
speed.
Reverse: Your snow thrower has two
reverse (R) speeds, with position
number one (1) being the slower speed.
Headlight
The headlight is on whenever the engine is running.
Clean-Out
Tool
The clean-out tool is designed to clear a clogged chute.
Refer to page 13 for instructions on how to properly use
it.
_
ARNING:
Never use your hand to clear a
clogged chute. Shut off engine and remain
behind handles until all moving parts have
stopped before unclogging. Use the clean-out
tool or a stick to unclog.
Wheel
Steering
Controls
The left and right wheel steering
controls are located on the underside
of the handles. Squeeze the right
control to turn right; squeeze the left control to turn left.
NOTE: Operate the snow thrower in open areas until
you are familiar with these controls.
Skid Shoe
The skid shoe position is determined by the condition of
the ground from where snow has to be removed. Higher
the snow level, lower will be the skid shoe level. Adjust
it accordingly. Refer to Skid ShoeAdjustment on page 8.
Before Starting Engine
Oil
The engine was shipped with oil in the engine. Check
oil level before each operation to ensure adequate oil in
the engine. For further instructions, refer to the steps on
page 15.
1.
Remove the dipstick from the oil fill.
2.
Check and make sure that the level of oil is up to
the FULL mark on the dipstick.
3.
If the oil level is not up to FULL, pour fresh oil slowly
through the plug. Replace oil fill dipstick and check
oil level again.
Gas
WARNING:
Gasoline is flammable; use
caution when handling or storing it.
WARNING:
Do not fill fuel tank while the
snow thrower is running, when it is hot or when
it is in an enclosed area.
WARNING:
Keep your snow thrower away
from any open flame or an electrical spark and
do not smoke while filling the fuel tank.
1.
Store gasoline in a clean, approved container and
keep the cap in place on the container.
2.
Make sure that the container from which you pour
the gasoline is clean and free from rust or other
foreign particles.
3.
A plastic cap is provided inside the fuel fill opening
to protect the tank during manufacturing. Remove
and discard. Use the threaded fuel tank cap to
close after fill-up.
4.
Always fill the fuel tank outdoors and use a funnel
or spout to prevent spilling
5.
Fill fuel tank with clean, fresh, unleaded grade
automotive gasoline.
6.
Never fill the fuel tank completely. Fill the tank to
within 1/2" from the top to provide space for
expansion of fuel.
7.
Make sure to wipe off any spilled fuel before
starting the engine.
8.
Atthe end of the job, emptythe fuel tank ifthe snow
thrower is not going to be used for30 days or
longer. See oft-season storage instructions on
page 22.
To Start Engine
_
ARNING:
Be sure no one other than the
operator is standing near the snow thrower
while starting or operating. Do not operate this
snow thrower unless the chute assembly has
been properly installed and is secured.
10
Hide quick links:
Advertisement
Table of Contents
