Page 1
Operator’s Manual ® 28” SNOW THROWER Model No. 247.88791 • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST CAUTION: Before using • ESPAÑOL this product, read this manual and follow all safety rules and operating instructions. Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A.
Craftsman full Warranty When operated and maintained according to all supplied instructions, if this Craftsman snow thrower fails due to a defect in material or workman- ship within two years from the date of purchase, call 1-800-4-MY-HOME (1-800-469-4663) to arrange for free in-home repair (or replacement if repair proves impossible).
SAFETY INSTRUCTIONS Warning Danger This machine was built to be operated according to the safe opera- This symbol points out important safety instructions which, if not tion practices in this manual. As with any type of power equipment, followed, could endanger the personal safety and/or property of carelessness or error on the part of the operator can result in serious yourself and others.
Page 4
SAFETY INSTRUCTIONS Safe Handling of Gasoline • Exercise extreme caution when operating on or crossing gravel surfaces. Stay alert for hidden hazards or traffic. To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are •...
Page 5
SAFETY INSTRUCTIONS maintenanCe & storage Do not moDify engine • Never tamper with safety devices. Check their proper operation To avoid serious injury or death, do not modify engine in any way. regularly. Refer to the maintenance and adjustment sections of Tampering with the governor setting can lead to a runaway engine and this manual.
Page 6
SAFETY INSTRUCTIONS safety symbols This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate. Symbol Description READ THE OPERATOR’S MANUAL(S) Read, understand, and follow all instructions in the manual(s) before attempting to assemble and operate WARNING—...
SAFETY LABELS DANGER NEVER PUT HAND IN CHUTE. CONTACT WITH ROTATING PARTS CAN AMPUTATE FINGERS AND HANDS. SHUT OFF ENGINE AND WAIT UNTIL ALL MOVING PARTS HAVE STOPPED BEFORE UNCLOGGING. USE CLEAN-OUT TOOL OR WOODEN STICK TO UNCLOG DISCHARGE CHUTE.
ASSEMBLY NOTE: References to right or left side of the snow thrower are determined from behind the unit in the operating position (standing directly behind the snow thrower, facing the handle panel). Chute Control Head remoVing from Carton Cut the corners of the carton and lay the sides flat on the ground. Chute Support Remove and discard all packing inserts.
Page 9
ASSEMBLY Place chute onto chute base and ensure hex rod is positioned Chute Control under handle panel. Install hex bolt previously removed but do Top View Input not secure with wing nut at this time. See Figure 4. Squeeze the trigger on the handle panel joystick and rotate the chute by hand to face forward.
Page 10
ASSEMBLY 7. Insert the hex end of chute rod into the input shaft below joystick on handle panel. Make sure to line up the hole in the hex end of chute rod with the arrow on the input shaft. See Figure 7. NOTE: The chute rod will fit snuggly into the input shaft.
Page 11
ASSEMBLY 10. Check that all cables are properly routed through the cable guide on the engine. See Figure 10. NOTE: For smoothest operation, the cables should all be to the left of the chute control rod. 11. The extension cord for the electric starter is fastened with a cable tie to the rear of the auger housing for shipping purposes.
Page 12
ASSEMBLY Chute Clean-out tool A chute clean-out tool is fastened to the top of the auger housing with a mounting clip. See Figure 12. The tool is designed to clear a chute assembly of ice and snow. This item is fastened with a cable tie at the factory.
Page 13
ASSEMBLY auger Control Warning Prior to operating your snow thrower, carefully read and follow all instructions below. Perform all adjustments to verify your snow thrower is operating safely and properly. Check the adjustment of the auger control as follows: When the auger control is released and in the disengaged “up” position, the cable should have very little slack.
Remove the key when the snow thrower is not in use. Unthread the gas cap to add gasoline to the fuel tank. meets ansi safety standards Craftsman Snow Throwers conform to the safety standard of the American National Standards Institute (ANSI).
Page 15
OPERATION tHrottle Control The auger control is located on the left handle. Squeeze the control grip against the handle to engage the auger and start snow throwing action. Release to stop. DriVe Control/ auger Control loCk The throttle control is located on the rear of the engine. It regulates the DRIVE speed of the engine and will shut off the engine when moved into the CONTROL...
Page 16
OPERATION Clean-out tool • Refuel in a well-ventilated area with the engine stopped. Do not smoke or allow flames or sparks in the area where the engine is Warning refueled or where gasoline is stored. • Do not overfill the fuel tank. After refueling, make sure the tank Never use your hands to clear a clogged chute assembly.
Page 17
OPERATION to engage DriVe Move throttle control to FAST (rabbit) position. With the throttle control in the Fast (rabbit) position, move shift Move choke to the CHOKE position (cold engine start). If lever into one of the six forward (F) positions or two reverse (R) engine is warm, place choke in RUN position.
SERVICE AND MAINTENANCE maintenanCe sCHeDule Warning Before performing any type of maintenance/service, disengage all Follow the maintenance schedule given below. This chart describes controls and stop the engine. Wait until all moving parts have come to service guidelines only. Use the Service Log column to keep track of a complete stop.
Page 19
SERVICE AND MAINTENANCE Reinstall the drain plug and tighten it securely. Refill with the recommended oil and check the oil level. Recommended Oil Usage chart. The engine’s oil capacity is 37 ounces. Synthetic 0W-30 5W-30 -40º -20º 0º 20º 40º Oil Drain -30º...
Page 20
SERVICE AND MAINTENANCE Caution The spark plug must be tightened securely. A loose spark plug can become very hot and can damage the engine. lubriCation gear shaft The gear (hex) shaft should be lubricated at least once a season or after every 25 hours of operation.
Page 21
SERVICE AND MAINTENANCE aDjustments shift Cable If the full range of speeds (forward and reverse) cannot be achieved, refer to the figure to the right and adjust the shift cable as follows: Place the shift lever in the fastest forward speed position (F6). Loosen the hex nut on the shift cable index bracket.
Page 22
SERVICE AND MAINTENANCE auger Control Refer to the Assembly section for instructions on adjusting the auger control cable. skid shoes Refer to the Assembly section for instructions on adjusting the skid shoes. belt rePlaCement auger belt To remove and replace your snow thrower’s auger belt, proceed as follows: To prevent spillage, remove all fuel from tank by running engine until it stops.
Page 23
SERVICE AND MAINTENANCE Remove the belt from around the auger pulley, and slip the belt between the support bracket and the auger pulley. See Figure 31. Reassemble auger belt by following these instructions in opposite order and manner of removal. Perform the Auger Control test outlined in the Assembly section of this manual.
OFF-SEASON STORAGE If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last possibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top performance from the snow thrower for many more years. PreParing snoW tHroWer PreParing engine •...
TROUBLESHOOTING Problem Cause Remedy Engine fails to start Choke control not in CHOKE position. Move choke control to CHOKE position. Spark plug wire disconnected. Connect wire to spark plug. Faulty spark plug. Clean, adjust gap, or replace. Fuel tank empty or stale fuel. Fill tank with clean, fresh gasoline.
Page 38
mtD Consumer grouP inC (mtD), the California air resources board (Carb) and the united states environment Protection agency (u. s. ePa) emission Control system Warranty statement (owner’s Defect Warranty rights and obligations) EMISSION CONTROL SYSTEM COVERAGE IS APPLICABLE TO CERTIFIED ENGINES PURCHASED IN CALIFORNIA IN 2005 AND THERE- AFTER, WHICH ARE USED IN CALIFORNIA, AND TO CERTIFIED MODEL YEAR 2005 AND LATER ENGINES WHICH ARE PURCHASED AND USED ELSEWHERE IN THE UNITED STATES.
Page 39
(4) Repair or replacement of any warranted part under the warranty provisions of this article must be performed at no charge to the owner at a warranty station. (5) Notwithstanding the provisions of Subsection (4) above, warranty services or repairs must be provided at all MTD distribution centers that are franchised to service the subject engines.
Page 40
look for relevant emissions Durability Period and air index information on your engine emissions label Engines that are certified to meet the California Air Resources Board (CARB) Tier 2 Emission Standards must display information regarding the Emissions Durability Period and the Air Index. Sears, Roebuck and Co., U.S.A. makes this information available to the consumer on our emission labels.
REPAIR PROTECTION AGREEMENT Congratulations on making a smart purchase. Your new Craftsman® Once you purchase the Agreement, a simple phone call is all that it product is designed and manufactured for years of dependable opera- takes for you to schedule service. You can call anytime day or night, or tion.
DECLARACIÓN DE GARANTÍA garantía total Craftsman Cuando hecho funcionar y mantenido según todas las instrucciones suministradas, si este lanzador de nieve falla debido a un defecto en mate- rial o habilidad dentro de dos años de la fecha de compra, llame al 1-800-4-MY-HOME (1-800-469-4663) para organizar de forma gratuita en la casa de reparación (si la reparación o la sustitución resulte imposible).
INSTRUCCIONES DE SEGURIDAD aDVertenCia Peligro Esta máquina fue construida para ser operada de acuerdo con La presencia de este símbolo indica que se trata de instrucciones las reglas de seguridad contenidas en este manual. Al igual que importantes de seguridad que se deben respetar para evitar con cualquier tipo de equipo motorizado, un descuido o error por poner en peligro su seguridad personal y/o material y la de otras parte del operador puede producir lesiones graves.
Page 44
INSTRUCCIONES DE SEGURIDAD Manejo seguro de la gasolina • Nunca opere la máquina si falta un montaje del canal o si el mismo está dañado. Mantenga todos los dispositivos de seguri- Para evitar lesiones personales o daños materiales tenga mucho dad en su lugar y en funcionamiento.
Page 45
INSTRUCCIONES DE SEGURIDAD • Para encender el motor, jale de la cuerda lentamente hasta que • Según la Comisión de Seguridad de Productos para el Consu- sienta resistencia, luego jale rápidamente. El repliegue rápido de midor de los Estados Unidos (CPSC) y la Agencia de Protección la cuerda de arranque (tensión de retroceso) le jalará...
Page 46
INSTRUCCIONES DE SEGURIDAD símbolos De seguriDaD Esta página describe los símbolos y figuras de seguridad internacionales que pueden aparecer en este producto. Lea el manual del operador para obtener la información terminada sobre seguridad, reunirse, operación y mantenimiento y reparación. Símbolo Descripción LEA EL MANUAL DEL OPERADOR (S)
MONTAJE NOTA: las referencias al lado derecho o y ciertos de la máquina quitanieve se determinan desde la parte posterior de la unidad en Cabezal de posición de operación (permaneciendo directamente detrás de la Control del máquina quitanieve, mirando hacia el panel de la manija). Canal Ménsula extraCCión De la uniDaD De la Caja...
Page 48
MONTAJE 4. Ubique el canal sobre la base del mismo y garantizar la varilla hex Cabezal de agonal está situado bajo el panel manejar. Instalar el perno Control del Vista desde Arriba hexagonal previamente eliminado, pero no seguro con tuerca de Canal mariposa en este momento.
Page 49
MONTAJE 7. Inserte la varilla hexagonal dentro del engranaje del piñón por debajo de la palanca de control. Asegúrese de alinear el orificio en la varilla hexagonal con la flecha en el engranaje del piñón. Vea la figura 7. NOTA: El orificio es una referencia para alinear la varilla con la flecha indicadora en el engranaje del piñón.
Page 50
MONTAJE 10. Controle que todos los cables estén adecuadamente dirigidos a través de la guía de cables en el motor. Vea la figura 10. NOTA: Para más suave funcionamiento, los cables deben estar a la izquierda de la varilla hexagonal. 11.
Page 51
MONTAJE Herramienta de limpieza del Canal Hay una herramienta de limpieza del canal iajustada a la parte superior de la caja de la barrena con un pasador de ensamblado. Vea la figura 12. La herramienta está diseñada para limpiar el hielo y la nieve del montaje de un canal.
Page 52
MONTAJE NOTA: Si tiene que usar la máquina quitanieve sobre grava, mantenga la zapata antideslizante en la posición más elevada para lograr una separación máxima entre el piso y la placa de raspado. Para ajustar las zapatas antideslizantes: Afloje las cuatros tuercas hexagonales (dos en cada lado) y los pernos del carro.
El faro se encuentra en cada vez que el motor esté en marcha. Cumple con los estándares de seguridad de ansi Las máquinas quitanieve de Craftsman cumplen con los estándares de seguridad del instituto estadounidense de estándares nacionales (ANSI).
Page 54
OPERACIÓN Control Del regulaDor Control De la barrena CONTROL DE LA BARRENA El control del regulador está ubicado en la parte trasera del motor. Regula la velocidad del motor, y lo apaga cuando se lo coloca en la posición STOP (detención). manija Del arranCaDor De retro- Ceso Esta manija se utiliza para arrancar el motor manualmente.
Page 55
OPERACIÓN rueDa que ConDuCe manDos Vuelva a ajustar la herramienta de limpieza al pasador de en- samblado ubicado en la parte posterior de la caja de la barrena, La rueda izquierda y derecha que conduce mandos es localizada en la inserte de nuevo la llave de encendido y encienda el motor de la parte oculta de los mangos.
Page 56
OPERACIÓN • No llene en exceso el tanque de combustible. Después de cargar Determine si el cableado de su hogar es un sistema de tres cables combustible, asegúrese de que el tapón del tanque esté bien conectado a tierra. Consulte con un electricista matriculado si no está cerrado y asegurado.
Page 57
OPERACIÓN DetenCión Del motor arrancador de retroceso Deje encendido el motor durante algunos minutos antes de detenerlo PreCauCión para permitir que se seque la humedad en el mismo. No tire de la manija del arrancador mientras el motor está en marcha. Mueva el control del regulador a la posición OFF.
SERVICIO Y MANTENIMIENTO lista De mantenimiento aDVertenCia Antes de realizar cualquier tipo del mantenimiento/servicio, suelte Siga la lista de mantenimiento dada abajo. Esta carta describe pautas todos los mandos y pare el motor. Espere hasta que todas las partes de servicio sólo. Use la columna de Tronco de Servicio para guardar de movimiento hayan venido a una parada completa.
Page 59
SERVICIO Y MANTENIMIENTO Cambio de aceite del motor NOTA: Cambie el aceite después de las 5 primeras horas de operación y después de cada 50 horas de operación o una vez por temporada. Vacíe el combustible del tanque haciendo funcionar el motor hasta que el tanque de combustible esté...
Page 60
SERVICIO Y MANTENIMIENTO Mida l a separación de bujía con un calibrador. Corrija de ser necesario torciendo el electrodo lateral. Vea la Figura 19. La separación debe establecerse entre 0,02 y 0,03 pulgadas (0,60- Electrodo 0,80 mm). Verifique que la arandela de la bujía esté en buenas condiciones y enrósquela manualmente para no estropear la rosca.
Page 61
SERVICIO Y MANTENIMIENTO NOTA: Las zapatas de esta máquina tienen dos bordes de desgaste. Cuando un lado se desgasta, se las puede rotar 180º para usar el otro borde. Para retirar las zapatas antideslizantes: Quite los cuatro pernos del carro, arandelas (si corresponde), y las tuercas de brida hexagonales que los aseguran a la máquina quitanieve.
Page 62
SERVICIO Y MANTENIMIENTO Ubique la ménsula hacia arriba para brindar más juego (o hacia abajo para aumentar la tensión del cable). Vuelva a apretar la tuerca hexagonal superior y repetir los pasos 1 a 4. Varilla de control del canal Para lograr una mayor engagment varilla hexagonal en el piñón de artes en el marco del panel de manejar, es necesario ajustar la varilla de control del canal.
Page 63
SERVICIO Y MANTENIMIENTO Gire con cuidado la máquina quitanieve hacia arriba y hacia delante de manera que quede apoyada sobre la caja de la barrena. Saque la cubierta del marco desde debajo de la máquina quitanieve retirando los tornillos autorroscantes que la aseguran. Vea la figura 28.
Page 64
SERVICIO Y MANTENIMIENTO Saque la correa de la barrena de la polea del motor. Tome la polea loca y gírela hacia la derecha. Vea la figura Levante la correa de la barrena para sacarla de la polea del motor. 4. Gire con cuidado la máquina quitanieve hacia arriba y hacia delante de manera que quede apoyada sobre la caja de la barrena.
ALMACENAMIENTO FUERA DE TEMPORADA Si no se va a utiliza el equipo durante 30 días o más, o si es el final de la temporada de nieve y ya no existe posibilidad de que nieve, es necesario almacenar el equipo de manera adecuada. Siga las instrucciones de almacenamiento que se indican a continuación para garantizar el rendimiento máximo de la máquina quitanieve durante muchos años .
SOLUCIÓN DE PROBLEMAS Problema Causa remedio El motor no arranca La palanca de obturación no está en la Ponga el interruptor en la posición CHOKE (obtura- posición ON (encendido) ción). Se ha desconectado el cable de la bujía Conecte el cable a la bujía. La bujía no funciona correctamente Limpie, ajuste la distancia disruptiva o cambie.
Page 67
SOLUCIÓN DE PROBLEMAS Problema Causa remedio Pérdida de potencia El cable de la bujía está flojo Conecte y ajuste el cable de la bujía. El orificio de ventilación del tapón de Retire el hielo y la nieve del tapón de llenado del llenado del combustible está...
Page 68
mtD Consumer grouP, inC. (mtD), el bordo de recursos de aire de California (Carb) y la agencia de Protección medioambiental de estados unidos (u. s. ePa) Declaración de garantía del sistema de Control de emisiones (Derechos y obligaciones del propietario según la garantía contra defectos) LA COBERTURA DE SISTEMA DE CONTROL DE EMISIÓN ES APLICABLE A MOTORES CERTIFICADOS COMPRADOS EN CALIFORNIA EN 2005 Y A PARTIR DE ENTONCES, QUE SON USADOS EN CALIFORNIA, Y HASTA AÑO 2005 DE MODELO CERTIFICADO Y MOTORES POSTERIORES QUE SON COMPRADOS Y USADOS EN OTRA PARTE EN LOS ESTADOS UNIDOS.
Page 69
reemplazada según la garantía se garantizará por el resto del período de garantía. Cualquier pieza garantizada que esté programada para reemplazo según el mantenimiento requerido de conformidad con las instruc- ciones escritas de la Subsección (c) se garantiza por el período de tiempo anterior a la primera fecha de reemplazo programada para esa pieza.
Page 70
busque el período de duración de emisiones importantes yla información de clasificación de aire en la etiqueta de emisiones de su motor Los motores cuyo cumplimiento con los estándares de emisión Tier 2 de la Comisión de Recursos Ambientales de California (CARB) esté...
Felicitaciones por haber realizado una adquisición inteligente. El Una vez adquirido el Acuerdo, puede programar el servicio con producto Craftsman® que ha adquirido está diseñado y fabricado tan sólo realizar una llamada telefónica. Puede llamar en cualquier para brindar muchos años de funcionamiento confiable. Pero como momento del día o de la noche o programar un servicio en línea.
Page 72
Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself.