Dukane 8104HW User Manual
  1. Manuals
  2. Brands
  3. Dukane Manuals
  4. Projector
  5. 8104HW
  6. User manual

Dukane 8104HW User Manual

Lcd data video projector
Hide thumbs Also See for 8104HW:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
LCD Data Video Projector
Concise User's Manual
Information in this Guide may change due to product improvements. To obtain the latest
manuals, literature, and software please visit the Dukane web site at; www.dukane.com/av
and look at the specific model SUPPORT or DOWNLOADS section.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
avservice@dukane.com
www.dukane.com/av
MODEL 8104HW
403-8104HW- Concise-00

Advertisement

Table of Contents
loading

Related Manuals for Dukane 8104HW

Summary of Contents for Dukane 8104HW

  • Page 1 MODEL 8104HW Information in this Guide may change due to product improvements. To obtain the latest manuals, literature, and software please visit the Dukane web site at; www.dukane.com/av and look at the specific model SUPPORT or DOWNLOADS section. DUKANE CORP AV SERVICE DEPT...

  • Page 3: Table Of Contents

    Projector 8 104HW User's Manual (concise) Thank you for purchasing this projector. Please read through this manual before using this product, in order to use safely and utilize well the product. WARNING ►Before using this product, be sure to read all manuals for this product.

  • Page 4: First Of All

    First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them. WARNING This entry warns of a risk of serious personal injury or even death. CAUTION This entry warns of a risk of personal injury or physical damage.

  • Page 5: Regulatory Notices

    Regulatory notices About Electro-Magnetic Interference This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.

  • Page 6: About Waste Electrical And Electronic Equipment

    Regulatory notices (continued) About Waste Electrical and Electronic Equipment The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available.

  • Page 7: Arrangement

    Arrangement Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1280 x 800 Screen size (diagonal) Projection distance (±8%) Screen height (±8%) •...

  • Page 8: Connecting With Your Devices

    Connecting with your devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
  • Page 9 Connecting with your devices (continued) Microphone Speakers system (with an amplifier) Monitor RGB IN USB storage device COMPUTER IN2 COMPUTER IN1 HDMI USB TYPE B TYPE A DC5V 0.5A S-VIDEO AUDIO IN1 AUDIO IN3 AUDIO OUT MONITOR OUT CONTROL AUDIO IN2 VIDEO WARNING ►Use only the appropriate accessories.

  • Page 10: Connecting Power Supply

    Connecting power supply Put the connector of the power cord into the AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

  • Page 11: Using The Cable Cover

    Using the cable cover Utilize the cable cover as the guard and blind for the connecting parts. Connect the signal cables and the power cord to the projector first. Combine parts as shown in figure, and assemble the cable cover. Insert the three knobs on the cable cover into the three holes on the projector as shown in the figure.

  • Page 12: Preparing For The Remote Control

    Preparing for the remote control Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

  • Page 13: Turning On The Power

    Turning on the power STANDBY/ON button POWER indicator Make sure that the power cord is firmly and correctly connected to the projector and the outlet. Make sure that the POWER indicator is steady orange. Confirm that there is nothing that the MY SOURCE/ MY SOURCE/ lens door hits while opening.

  • Page 14: Adjusting The Projector's Elevator

    Adjusting the projector's elevator The projector has Front foot for inclinations and Rear foot for horizontals. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary, detach the spacer, and the elevator feet can be manually twisted to make more precise adjustments.

  • Page 15: Selecting An Aspect Ratio

    Focusing ASPECT button Use the FOCUS + and FOCUS – buttons on the projector or remote control to adjust the MY SOURCE/ COMPUTER VIDEO DOC.CAMERA VOLUME+/- button screen focus. AUTO ASPECT SEARCH BLANK MAGNIFY FREEZE PAGE VOLUME ＋ DOWN Selecting an aspect ratio KEYSTONE button ー...

  • Page 16: Turning Off The Power

    Turning off the power STANDBY/ON button Press the STANDBY/ON button on the POWER indicator projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds. Confirm that there is nothing that the lens door hits while closing. Press the STANDBY/ON button again while the MY SOURCE/ MY SOURCE/...

  • Page 17: Replacing The Lamp

    Replacing the lamp A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
  • Page 18 Replacing the lamp (continued) HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.

  • Page 19: Cleaning And Replacing The Air Filter

    Cleaning and replacing the air filter The air filter has two kinds of filters inside. Please check and clean the air filter periodically. When the indicators or a message prompts you to clean the air filter, comply with it as soon as possible.

  • Page 20: Replacing The Internal Clock Battery

    Replacing the internal clock battery This projector has internal clock that uses a battery. When the clock of the network function does not work correctly, please try solution by replacement of the battery: HITACHI MAXELL, part number CR2032 or CR2032H. Battery Cover Turn the projector off, and unplug the power cord.

  • Page 21: Caring For The Mirror And Lens

    Caring for the mirror and lens If the projection mirror or lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the mirror and lens, being cautious of handling. Turn the projector off and unplug the power cord from the power outlet.

  • Page 22: Using The Cd Manual

    Using the CD manual The other manuals for this product are written into the included CD-ROM titled “User’s Manual (detailed)”. Before using the CD-ROM, please read the following to ensure the proper use. System requirements The system for using the CD-ROM requires the following. Windows OS:Microsoft Windows...

  • Page 23: Specifications

    Specifications Item Specification Product name Liquid crystal projector Liquid Crystal Panel 1,024,000 pixels (1280 horizontal x 800 vertical) Lamp 210W UHP Speaker Power supply AC 100-120V/3.1A, AC 220-240V/1.6A Power consumption AC 100-120V:310 W, AC 220-240V:300W Temperature range 5 ~ 35°C (Operating) 345 (W) x 85 (H) x 303 (D) mm Size * Not including protruding parts.

  • Page 24: Troubleshooting - Warranty And After-Service

    They will tell you what warranty condition is applied. Please check the following web address where you may find the latest information for this projector. Product http:www.dukane.com/av information and Manuals : NOTE • The information in this manual is subject to change without notice.

Table of Contents