Page 1 Projector 8104WB/8105B/8106B User's Manual (detailed) Operating Guide Thank you for purchasing this projector. WARNING ►Before using this product, please read all manuals for this product. Be sure to read “Safety Guide” first. After reading them, store them in a safe place for future reference.
Page 2: Table Of Contents
Contents   Introduction . . . . . . . . . . . . . . . 3 SETUP menu . . . . . . . . . . . . . . 44 Features .
Page 3: Introduction
Use special caution for the lens. Note: Dukane models described in this document are manufactured by Hitachi and use the same firmware and software programs. The equivalent Dukane to Hitachi models are...
Page 4: Part Names
Introduction Part names HOT! Projector (1) Lamp cover (111) The lamp unit is inside. (2) Control panel (5) (11) (3) Elevator feet (x 2) (25) (4) Remote sensor (17) (13) (5) Lens (115) (10) (6) Intake vents (12) (7) Filter cover (113) The air filter and intake vent HOT! are inside.
Page 5 Introduction Part names (continued) Control panel (1) STANDBY/ON button (19) (2) INPUT button (22) (3) POWER indicator (19, 119) (4) TEMP indicator (119) (5) LAMP indicator (119) Buttons ◄/►/▲/▼ (6) FOCUS +/- buttons when no menu is displayed (26), or Cursor ◄/►...
Page 6 Introduction Part names (continued) Remote control (1) VIDEO button (23) (10) (2) COMPUTER button (23) (3) SEARCH button (24) MY SOURCE/ VIDEO COMPUTER DOC.CAMERA (4) STANDBY/ON button (19) ASPECT AUTO SEARCH BLANK (16) (12) (5) ASPECT button (24) MAGNIFY PAGE VOLUME FREEZE (14)
Page 7: Setting Up
Setting up Setting up Install the projector according to the environment and manner the projector will be used in. Arrangement Refer to table T-1 or T-2 and figures F-1 and F-2 at the end of User’s Manual (concise) to determine the screen size and projection distance. The values shown in the table are calculated for a full size screen.
Page 8 Setting up Arrangement (continued) WARNING ►Place the projector in a cool place, and ensure that there is sufficient ventilation. The high temperature of the projector could cause fire, burns and/or malfunction of the projector. • Do not stop-up, block or otherwise cover the projector's vents. •...
Page 9: Connecting With Your Devices
Setting up Arrangement (continued) NOTE • The projector may make a rattling sound when tilted, moved or shaken, since a flap to control the air flow inside of the projector has moved. Be aware that this is not a failure or malfunction. •...
Page 10 Setting up Connecting with your devices (continued) About Plug-and-Play capability • Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.
Page 11 Setting up Connecting with your devices (continued) NOTE • Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector. - Some signal may need an adapter to input this projector. - Some computers have multiple screen display modes that may include some signals which are not supported by this projector.
Page 12 Setting up Connecting with your devices (continued) • If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the device (87).
Page 13 Setting up Connecting with your devices (continued) To use network functions of the projector, connect the LAN port with the computer's LAN port, or with an access point that is connected to the computer with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, also connect the CONTROL port and an RS-232C port of the external device to communicate as a network terminal.
Page 14 Setting up Connecting with your devices (continued) NOTE • If an oversized USB storage device blocks the LAN port, use a USB extension cable to connect the USB storage device. • The HDMI port of this model is compatible with HDCP (High-bandwidth Digital Content Protection) and therefore capable of displaying a video signal from HDCP compatible DVD players or the like.
Page 15: Connecting To A Power Supply
Setting up Connecting to a power supply Put the connector of the power cord into the AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.
Page 16: Using The Cable Cover
Setting up Using the cable cover Utilize the cable cover as the guard and blind for the connecting parts. Connect the signal cables and the power cord to the projector first. Combine parts as shown in figure, and assemble the cable cover. Insert the three knobs on the cable cover into the three holes on the projector as shown in the figure.
Page 17: Remote Control
Remote control Remote control Installing the batteries Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place. Holding the hook part of the battery cover, remove it.
Page 18: Changing The Frequency Of Remote Control Signal
Remote control Changing the frequency of remote control signal MY SOURCE/ VIDEO COMPUTER DOC.CAMERA The accessory remote control has the two choices on signal ASPECT AUTO SEARCH BLANK frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control MAGNIFY PAGE VOLUME FREEZE ＋...
Page 19: Power On/Off
Power on/off Power on/off Turning on the power STANDBY/ON button Make sure that the power cord is firmly POWER indicator and correctly connected to the projector and the outlet. Make sure that the POWER indicator is steady orange (119). Confirm that there is nothing that the lens door hits while opening.
Page 20 Power on/off WARNING ►Never look into the projection lens or mirror while the projection lamp lights, since the projection lamp ray may cause a trouble on your eyes. ►Be careful not to pinch your finger with the lens door, to prevent an injury. ►Do not place the projector vertically with the lens door open as shown in the figure on the right.
Page 21: Turning Off The Power
Power on/off Turning off the power Press the STANDBY/ON button on the projector or the remote control. The message “Power off?” will appear on the screen for about 5 seconds. Confirm that there is nothing that the lens door hits while closing. Press the STANDBY/ON button again while the message appears.
Page 22: Operating
Operating Operating VOLUME +/- button Adjusting the volume MY SOURCE/ VIDEO COMPUTER DOC.CAMERA Use the VOLUME +/VOLUME - buttons to adjust the volume. ASPECT AUTO SEARCH BLANK A dialog will appear on the screen to aid you in adjusting the MAGNIFY PAGE VOLUME...
Page 23 Operating Selecting an input signal (continued) Press COMPUTER button on the remote control. COMPUTER button Each time you press the button, the projector switches its input port from the current port as below. MY SOURCE/ VIDEO COMPUTER DOC.CAMERA COMPUTER IN1  COMPUTER IN2  LAN ASPECT AUTO SEARCH...
Page 24: Searching An Input Signal
Operating Searching an input signal Press SEARCH button on the remote control. SEARCH button The projector will start to check its input ports as below in order to find any input signals. MY SOURCE/ VIDEO COMPUTER DOC.CAMERA When an input is found, the projector will stop searching ASPECT AUTO SEARCH...
Page 25: Adjusting The Projector's Elevator
Operating Adjusting the projector's elevator The projector has Front foot for inclinations and Rear foot for horizontals. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary, detach the spacer, and the elevator feet can be manually twisted to make more precise adjustments.
Page 26: Using The Automatic Adjustment Feature
Operating FOCUS - button Press the FOCUS + or FOCUS - button on the remote control, or FOCUS + or FOCUS - button on the projector (5) MY SOURCE/ while no menu is on screen, to display the FOCUS box on VIDEO COMPUTER DOC.CAMERA...
Page 27: Adjusting The Position
VIDEO COMPUTER DOC.CAMERA ASPECT AUTO SEARCH BLANK MAGNIFY PAGE VOLUME FREEZE ＋ Operating DOWN ー MY BUTTON KEYSTONE MUTE Adjusting the position D-ZOOM FOCUS Press the POSITION button on the remote control while no menu MENU POSITION is on screen, to display the D-SHIFT (44) dialog on screen. ENTER RESET Use the ▲, ▼, ◄...
Page 28: Using The Magnify Feature
Operating Using the magnify feature Press the MAGNIFY ON button on the remote control. MAGNIFY ON/OFF button The picture will be magnified, and the MAGNIFY dialog will appear on the screen. When the MAGNIFY ON button is pressed for the first time after the projector is turned on, the MY SOURCE/ VIDEO COMPUTER...
Page 29: Temporarily Freezing The Screen
Operating Temporarily freezing the screen FREEZE button Press the FREEZE button on the remote control. The “FREEZE” indication will appear on the screen (however, the indication will not appear when the OFF is selected for MY SOURCE/ VIDEO COMPUTER DOC.CAMERA the MESSAGE item in the SCREEN menu (54)), and the ASPECT AUTO...
Page 30: Using The Menu Function
Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, MY SOURCE/ VIDEO COMPUTER DOC.CAMERA SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classified ASPECT AUTO SEARCH...
Page 31 Operating Using the menu function (continued) To close the MENU, press the MENU button again or select EXIT and press the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds. ●...
Page 32: Easy Menu
EASY MENU EASY MENU From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table. Item Description Using the ◄/► buttons switches the mode for aspect ratio. ASPECT See the ASPECT item in IMAGE menu (37).
Page 33 EASY MENU Item Description Using the ◄/► buttons switches the picture mode. The picture modes are combinations of GAMMA and COLOR TEMP settings. Choose a suitable mode according to the projected source. NORMAL ó CINEMA ó DYNAMIC ó BOARD(BLACK) PHOTO ó DAYTIME ó WHITEBOARD ó BOARD(GREEN) GAMMA COLOR TEMP NORMAL...
Page 34: Picture Menu
PICTURE menu PICTURE menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table. Item Description Using the ◄/►...
Page 35 PICTURE menu Item Description Using the ▲/▼ buttons switches the color temperature mode. To adjust CUSTOM Selecting a mode whose name includes CUSTOM and then pressing the ► button or the ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selected mode.
Page 36 PICTURE menu Item Description Using the ◄/► buttons adjusts the sharpness. Weak ó Strong SHARPNESS • There may be some noise and/or the screen may flicker for a moment when an adjustment is made. This is not a malfunction. Using the ▲/▼ cursor buttons changes the active iris control mode. PRESENTATION ó...
Page 37: Image Menu
IMAGE menu IMAGE menu From the IMAGE menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 38 IMAGE menu Item Description Using the ◄/► buttons adjusts the vertical position. Down ó Up • Over-adjusting the vertical position may cause noise to appear on the screen. If this occurs, please reset the vertical position to the default setting. Pressing the RESET button when the V POSITION V POSITION is selected will reset the V POSITION to the default setting.
Page 39 IMAGE menu Item Description Using the ◄/► buttons adjusts the horizontal phase to eliminate flicker. Right ó Left H PHASE • This item can be selected only for a computer signal or a component video signal. This function is unavailable for a signal from the LAN, USB TYPE A, USB TYPE B or HDMI port.
Page 40: Input Menu
INPUT menu INPUT menu From the INPUT menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 41: Ideo Format
INPUT menu Item Description The video format for S-VIDEO port and VIDEO port can be set. (1) Use the ▲/▼ buttons to select the input port. (2) Using the ◄/► buttons switches the mode for video format. AUTO ó NTSC ó PAL ó SECAM VIDEO FORMAT N-PAL ó...
Page 42: Omputer In , F
INPUT menu Item Description The computer input signal type for COMPUTER IN1 and IN2 ports can be set. (1) Use the ▲/▼ buttons to select the COMPUTER IN port to be set. (2) Use the ◄/► buttons to select the computer input signal type. AUTO ó...
Page 43 INPUT menu Item Description The resolution for the COMPUTER IN1 and COMPUTER IN2 input signals can be set on this projector. (1) In the INPUT menu select the RESOLUTION using the ▲/▼ buttons and press the ► button. The RESOLUTION menu will be displayed.
Page 44: Setup Menu
SETUP menu SETUP menu From the SETUP menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 45: Keystone
• The input signal has an aspect ratio of 16:9, 16:10 or verticallly PICT. POSIT. H smaller than 16:10, while ASPECT is set to NORMAL. (8104WB) • Horizontal size of the displayed image is full on the effective display area, while the ASPECT is set to NATIVE.
Page 46 SETUP menu Item Description This item allows you to adjust the shape of the projected image in each of the corners and sides. (1) Choose a corner or side to adjust using the ▲/▼/◄/► buttons and press the ENTER or INPUT button. (2) Adjust the distortion as below.
Page 47: Auto Eco Mode
SETUP menu Item Description • While the distortion is adjusted with the PERFECT FIT function, keystone adjustment feature is unavailable. To correct the keystone distortion, reset the adjustment of all the corners and sides. • The adjustable range of this correction will vary among inputs. For some input, this function may not work well.
Page 48 SETUP menu Item Description Pressing the ►button displays the dialog for changing the INSTALLATION setting. INSTALLATION Use the ▲/▼ buttons to select the desired setting on the INSTALLATION dialog, and press the ENTER button of the remote control or the INPUT button of the projector to execute. If TRANSITION DETECTOR is ON and the INSTALLATION status is changed, the TRANSITION DETECTOR ON alarm (84) will be displayed when the projector is restarted.
Page 49 SETUP menu Item Description While the image signal from the input port chosen in step (1) is projected, the image signal from the input port selected in step (2) is output to MONITOR OUT port. (1) Choose a picture input port using ▲/▼ buttons. Choose STANDBY to select the picture output in the standby mode.
Page 50: Audio Menu
AUDIO menu AUDIO menu From the AUDIO menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or the ENTER button to execute the item. Then perform it according to the following table.
Page 51 AUDIO menu Item Description Using the ▲/▼ buttons switches the input level to match that of the microphone connected to the MIC port. MIC LEVEL HIGH ó LOW HIGH: for a microphone with an amplifier. LOW: for a microphone without an amplifier. Using the ◄/►...
Page 52: Screen Menu
SCREEN menu SCREEN menu From the SCREEN menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item. Then perform it according to the following table.
Page 53 SCREEN menu Item Description This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure.
Page 54 SCREEN menu Item Description Using the ▲/▼ buttons turns on/off the MyScreen lock function. ON ó OFF When the ON is selected, the item MyScreen is locked. Use this MyScreen Lock function for protecting the current MyScreen. • This function cannot be selected when the ON is selected to the MyScreen PASSWORD item in SECURITY menu (82).
Page 55 SCREEN menu Item Description Each input port for this projector can have a name applied to it. (1) Use the ▲/▼ buttons on the SCREEN menu to select SOURCE NAME and press the ► or ENTER button. The SOURCE NAME menu will be displayed. (2) Use the ▲/▼...
Page 56 SCREEN menu Item Description (6) The current name will be displayed on the first line. Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄...
Page 57 SCREEN menu Item Description The C.C. is the function that displays a transcript or dialog of the audio portion of a video, files or other presentation or other relevant sounds. It is required to have NTSC format video or 480i@60 format component video source supporting C.C.
Page 58: Option Menu
OPTION menu OPTION menu From the OPTION menu, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons, and press the ► cursor button or ENTER button to execute the item, except for the items LAMP TIME and FILTER TIME.
Page 59 OPTION menu Item Description Using the ▲/▼ buttons adjusts the time to count down to automatically turn the projector off. Long (max. 99 minutes) ó Short (min. 0 minute = DISABLE) When the time is set to 0, the projector is not turned off automatically. AUTO POWER When the time is set to 1 to 99, and when the passed time with no- signal or an unsuitable signal reaches at the set time, the projector...
Page 60 OPTION menu Item Description This item is to assign one of the following functions to MY BUTTON 1/2 on the remote control (6). (1) Use the ▲/▼ buttons on the MY BUTTON menu to select a MY BUTTON - (1/2) and press the ► or ENTER button to display the MY BUTTON setup dialog.
Page 61 OPTION menu Item Description • ACTIVE IRIS: Changes the active iris mode. • PICTURE MODE: Changes the PICTURE MODE (33). • FILTER RESET: Displays the filter time reset confirmation dialogue (59). • TEMPLATE: Makes the template pattern selected to the TEMPLATE item (56) appear or disappear.
Page 62 OPTION menu Item Description Selecting this item displays the SERVICE menu. Select an item using the ▲/▼ buttons, and press the ► button or the ENTER button on the remote control to execute the item. ALTITUDE Using the ▲/▼ buttons switches the rotation speed of the cooling fans.
Page 63 OPTION menu Item Description KEY LOCK (1) Use the ▲/▼ buttons to select CONTROL PANEL or REMOTE CONTROL. (2) Use the ◄/► buttons to turn the key lock function on/off. When ON is selected, all buttons on the projector or remote control except the STANDBY/ON button are locked.
Page 64 OPTION menu Item Description REMOTE FREQ. (1) Use the ▲/▼ button to change the projector's remote sensor frequency setting (17, 18). 1:NORMAL ó 2:HIGH (2) Use the ◄/► button to change the projector's remote sensor on or off. ON ó OFF The factory default setting is for both 1:NORMAL and 2:HIGH to be on.
Page 65 OPTION menu Item Description COMMUNICATION TYPE Select the communication type for transmission via the CONTROL port. NETWORK BRIDGE: Select this type, if it is required to control an external device as a network terminal, via this projector from the computer. The CONTROL port doesn't accept RS-232C commands (Network Bridge Function in the User’s Manual - Network Guide)
Page 66 OPTION menu Item Description RESPONSE LIMIT TIME Select the time period to wait for receiving response data from other device communicating by the NETWORK BRIDGE and the HALF-DUPLEX through the CONTROL port. OFF ó 1s ó 2s ó 3s OFF: Select this mode if it is not required to check the responses from the device that the projector sends data to.
Page 67 OPTION menu Item Description The following items are exempted. OPTION: LAMP TIME, FILTER TIME, SERVICE(GHOST) NETWORK: WIRELESS AND WIRED SETUP (IP ADDRESS, SUBNET MASK, DEFAULT GATEWAY, DATE AND TIME), MY IMAGE, PRESENTATION SECURITY: MY TEXT DISPLAY • Operation is not available if SECURITY_ CLONNING LOCK is turned ON.
Page 68 OPTION menu Item Description Load MyScreen data • Please save the image data as "pj_logo.bmp" or "pj_logo.gif" into USB memory. • Please note that the only compatible formats are as follows. -File format Windows BMP bit/pixel: 2/4/8/15/16/24/32bit Compression format : Without compression/RLE -Image size: more than 36x36, less than 1280x800 •...
Page 69 OPTION menu Item Description INFORMATION Selecting this item displays a dialog titled “INPUT_INFORMATION”. It shows the information about the current input. • The “FRAME LOCK” message on the dialog means the frame lock function is working. • This item can't be selected for no signal and sync out. SERVICE •...
Page 70: Network Menu
NETWORK menu NETWORK menu Remember that incorrect network settings on this projector may cause trouble on the network. Be sure to consult with your network administrator before connecting to an existing access point on your network. Select “NETWORK” from the main menu to access the following functions.
Page 71 NETWORK menu Item Description Use the ▲/▼ buttons to turn DHCP on/off. ON ó OFF Select OFF when the network does not have DHCP DHCP enabled. To save the setting, press the ► button. (Dynamic Host • When the “DHCP” setting changes to “ON”, it Configuration takes a little time to obtain IP address from DHCP Protocol)
Page 72 NETWORK menu Item Description Use the ▲/▼/◄/► buttons to enter the Year (last two digits), Month, Date, Hour and Minute. • When this item is set, the same item in the WIRED SETUP menu is overwritten with the same setting (76). •...
Page 73 NETWORK menu Item Description Use the ▲/▼ buttons to select the SSID to display the SSID menu. #1 DEFAULT ó #2 DEFAULT ó #3 DEFAULT #5 CUSTOM ó #4 DEFAULT Select one of the DEFAULT (#1~#4) and press ► or ENTER button. To adjust CUSTOM Press the ►...
Page 74 NETWORK menu Item Description "Selecting this item displays the WIRELESS_INFORMATION dialog for viewing the wireless LAN settings." Use the ▲/▼ buttons to switch the page. The first page shows the wireless LAN settings. The second and subsequent pages display the signal information of wireless LAN connection devices.
Page 75: Ired Setup , W
NETWORK menu Item Description Selecting this item displays the WIRED SETUP menu for the wired LAN. Use the ▲/▼ buttons to select an item, and the ► or ENTER button on the remote control to perform the item. Use the ▲/▼ buttons to turn DHCP on/off. ON ó...
Page 76 NETWORK menu Item Description Use the ▲/▼ buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your computer. If unsure, consult your IT manager. TIME Use the ► button to return to the menu after DIFFERENCE setting the TIME DIFFERENCE.
Page 77: Rojector Name
NETWORK menu Item Description (1) Use the ▲/▼ buttons on the NETWORK menu to select the PROJECTOR NAME and press the ► button. The PROJECTOR NAME dialog will be displayed. (2) The current PROJECTOR NAME will be displayed on the first 3 lines.
Page 78 NETWORK menu Item Description Selecting this item displays the MY IMAGE menu. Use the application to transfer the im- age data. It can be downloaded from the Hitachi web site. Use the ▲/▼ buttons to select an item which is a still image by the MY IMAGE (My Image Function in the Network Guide) and the ►...
Page 79 NETWORK menu Item Description Selecting this item displays the PRESENTATION menu. Use ▲/▼ buttons to select one of the following items, then press ► or ENTER button to use the function. • To use Network Presentation, an exclusive application, "LiveViewer" is required.
Page 80 NETWORK menu Item Description • To change from Single PC mode to Multi PC mode, press ► button to choose OK in the dialog and press the ENTER or INPUT button. The display mode is changed. • For details on how to switch the display mode to Multi PC mode on your computer, refer to the MULTI PC...
Page 81: Security Menu
SECURITY menu SECURITY menu This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed. To use SECURITY menu: User registration is required before using the security functions. Enter to the SECURITY menu 1.
Page 82: Myscreen Password
SECURITY menu Item Description The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the currently registered MyScreen image from being overwritten. 1 Turning on the MyScreen PASSWORD 1-1 Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ►...
Page 83 SECURITY menu Item Description PIN LOCK is a function which prevents the projector from being used unless a registered Code is input. 1 Turning on the PIN LOCK 1-1 Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.
Page 84: Ransition Detector
SECURITY menu Item Description If this function is set to ON and the vertical angle of the projector or the INSTALLATION setting is different from the previous recorded setting, the TRANSITION DETECTOR ON alarm will be displayed and the input signal will not be displayed.
Page 85 SECURITY menu Item Description The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT; • The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting. •...
Page 86 SECURITY menu Item Description (1) Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu. (2) Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off.
Page 87: Presentation Tools
Presentation tools Presentation tools Presentation tools The projector has the following two convenient tools that enable on-screen presentations easily and quickly: - PC-LESS Presentation (below) - Drawing function Drawing function enables you to draw on the projector’s screen with USBmouse or tablets connected to the USB TYPE A ports. For details of Drawing function, refer to the Operating Guide - Drawing function.
Page 88: Thumbnail Mode
• Files with a resolution larger than the following are not supported. 8105B, 8106B: 1024 x 768 (Still)， 768 x 576 (Movie) 8104WB: 1280 x 800 (Still)， 768 x 576 (Movie) (* Some computers may not support 1280 x 800.) •...
Page 89 Presentation tools Presentation tools PC-LESS Presentation (continued) Operating by buttons or keys You can control the images on the Thumbnail screen with the remote control, control panel or Web Remote Control. The following functions can be supported while the Thumbnail is displayed. Button operation Functions Web Remote...
Page 90 Presentation tools PC-LESS Presentation (continued) Operating by the menu on the Thumbnail screen You can also control the images by using the menu on the Thumbnail screen. Item Functions Moves to an upper folder. SORT Allows you to sort files and folders as following. Press the ►...
Page 91 Presentation tools PC-LESS Presentation (continued) NOTE • These operations are not accessible while the projector OSD is displayed. • The Thumbnail mode is able to display up to 20 files in one page. • It is not possible to change the input port by using the INPUT button when the Thumbnail screen, Slideshow, or Full Screen is displayed.
Page 92: Full Screen Mode
Presentation tools PC-LESS Presentation (continued) Full Screen Mode The Full Screen mode shows a full display image. To display in Full Screen mode, select an image in the Thumbnail screen. Then press the ENTER button on the remote control, the INPUT button on the control panel or click [ENTER] on the Web Remote Control.
Page 93 Presentation tools PC-LESS Presentation (continued) Operations for movie A remote control icon and a progress bar are displayed when one of the cursor buttons, ENTER button or INPUT button on the remote control, control panel or Web Remote Control is pressed or clicked while a movie is playing in the Full Screen mode.
Page 94: Slideshow Mode
Presentation tools PC-LESS Presentation (continued) Slideshow mode The Slideshow mode displays images in full screen and switches the images at intervals set in INTERVAL on the Thumbnail screen menu (90). You can start this function from the Slideshow menu. To display the Slideshow menu, select the SLIDESHOW button in the Thumbnail mode and press the ENTER button on the remote control, INPUT button on the control panel, or click [ENTER] on the Web Remote Control.
Page 95 Presentation tools PC-LESS Presentation (continued) You can play the Slideshow at your desired configuration. Configure the Slideshow items in the Thumbnail. 1) RETURN : Returns to the thumbnail mode. 2) PLAY : Play the Slideshow. 3) START : Set the beginning number of the Slideshow.
Page 96 Presentation tools PC-LESS Presentation (continued) Playlist The Playlist is a DOS format text file, which decides the order of displayed still image files in the Thumbnail or Slideshow. The playlist file name is “playlist.txt” and it can be edited on a computer. It is created in the folder that contains the selected image files when the PC-LESS Presentation is started or the Slideshow is configured.
Page 97: Drawing Function
Presentation tools Drawing Function Main Functions This function is an interactive tool for use with projector; it offers effective features for making classroom and business presentations more fun and easier to understand. Drawing on projected images You can draw pictures or text on images projected by our projectors. NOTE •...
Page 98 Presentation tools Drawing Function (continued) Connecting the Pen tablet (ex . TB-1)/USB mouse and USB memory device . Connect into the USB TYPE A port on your projector. To save an image that has been drawn, a USB memory device must also be connected to a USB TYPE A port of the projector.
Page 99 Presentation tools Drawing Function (continued) Wireless USB memory adapter device Tablet Computer USB TYPE B USB TYPE A USB TYPE A Projector Fig.2 Example of connections Wireless USB memory adapter device Mouse USB hub Computer Tablet USB TYPE A USB TYPE B USB TYPE A Projector Fig.3 Example of connections...
Page 100 Presentation tools Using the Drawing Function Touching/clicking Pen tablet (ex. TB-1)/USB mouse function key starts up the drawing mode. A tool bar like the fi gure below is displayed on the projector screen while in the drawing mode. Touching/clicking an icon on the tool bar enables the following functions.
Page 101 Presentation tools Using the Drawing Function (continued) 5. Erase Erases all the lines drawn with the pen. Projector Operates the projector. Operation Calls up and display the previous fi le in the USB memory device from that currently selected. This function is available when the projector is displaying a fi le from a USB memory device.
Page 102 Presentation tools Using the Drawing Function (continued) Projector Turns off the projector. Operation Touch/click the icon for three seconds or so. (Continued) • If you turn the projector off while using the drawing function, any unsaved drawings will be lost. Toggles between display/hide the Pattern (grid lines).
Page 103: Usb Display(Windows Computer)
Presentation tools USB Display(Windows computer) The projector can display images transferred from a computer via an USB cable (10). Hardware and software requirement for computer • OS: One of the following. (32 bit version only) ® Windows XP Home Edition /Professional Edition ®...
Page 104 Presentation tools USB Display(Windows computer) (continued) This application will appear in the Windows notification area once it starts. You can quit the application from your computer by selecting “Quit” on the menu. NOTE • The “LiveViewer” (refer to the Network Guide) and this application cannot be used at the same time.
Page 105 Presentation tools USB Display(Windows computer) (continued) Right-Click menu The menu shown in the right will be displayed when you right-click the application icon in the Windows notification area. Display : The Floating menu is displayed, and the icon disappears from the Windows notification area.
Page 106: Options Window
Presentation tools USB Display(Windows computer) (continued) Options window If you select the Option button on the Floating menu, the Options window is displayed. Optimize Performance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compression rate of JPEG data.
Page 107: Usb Display(Mac Computer)
Presentation tools USB Display(Mac computer) The projector can display images transferred from a computer via an USB cable (10). Hardware and software requirement for computer • OS: Mac OSX 10.5(Intel) Mac OSX 10.6(Intel) Mac OSX 10.7(Intel) This application is not compatible with Power PC. •...
Page 108 Presentation tools USB Display(Mac computer) (continued) NOTE • The “LiveViewer” (refer to the Network Guide) and this application cannot be used at the same time. If you connect your computer to the projector by using a USB cable while the “LiveViewer”...
Page 109 Presentation tools Presentation tools USB Display(Mac computer) (continued) Menu       If you select “Display” on the Right-Click menu, the Floating menu shown in the right will appear on your computer screen.  Start capture button The transmission to the projector is started and the images will be displayed.
Page 110 Presentation tools USB Display(Mac computer) (continued) Options window If you select the Option button on the Floating menu, the Options window is displayed. Optimize Performance The “LiveViewer Lite for USB” captures screenshots in JPEG data and sends them to the projector. The “LiveViewer Lite for USB” has two options that have different compression rate of JPEG data.
Page 111: Eystone Maintenance
Maintenance Maintenance Replacing the lamp A lamp has finite product life. Using the lamp for long periods of time could cause the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended.
Page 112: Lamp Warning
Maintenance Replacing the lamp (continued) Lamp warning HIGH TEMPERATURE HIGH PRESSURE HIGH VOLTAGE WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.
Page 113: Cleaning And Replacing The Air Filter
Maintenance Cleaning and replacing the air filter The air filter unit of this projector consists of a filter cover, two kinds of filters, and a filter frame. The new double large filters system is expected to function longer. However, please check and clean it periodically to keep ventilation needed for normal operation of the projector.
Page 114 Maintenance Cleaning and replacing the air filter (continued) Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU. (1) Press the MENU button to display a menu. (2) Point at the FILTER TIME using the ▼/▲ button, then press the ► button. A dialog will appear.
Page 115: Caring For The Mirror And Lens
Maintenance Caring for the mirror and lens If the projection mirror or lens is flawed, soiled or fogged, it could cause deterioration of display quality. Please take care of the mirror and lens, being cautious of handling. Turn the projector off and unplug the power cord from the power outlet.
Page 116: Other Care
Maintenance Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the cabinet and remote control Incorrect care could have adverse influence such as discoloration, peeling paint, etc.
Page 117: Olor Temp Troubleshooting
Troubleshooting Troubleshooting If an abnormal operation should occur, stop using the projector immediately. WARNING ►Never use the projector if abnormal operations such as smoke, Troubleshooting strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately disconnect the power plug from the power outlet.
Page 118 Troubleshooting Related messages (continued) Message Description The internal temperature is rising. Please turn the power off, and allow the projector to cool down at least 20 minutes. After having confirmed the following items, please turn the power ON again. • Is there blockage of the air passage aperture? •...
Page 119: Regarding The Indicator Lamps
Troubleshooting Regarding the indicator lamps When operation of the LAMP, TEMP and POWER indicators differs from usual, check and cope with it according to the following table. POWER LAMP TEMP Description indicator indicator indicator Lighting Turned Turned The projector is in a standby state. Please refer to the section “Power on/off”.
Page 120 Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP Description indicator indicator indicator There is a possibility that the interior portion has become heated. Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has sufficiently cooled down, please make Blinking confirmation of the following items, and then turn the power on again.
Page 121 Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP Description indicator indicator indicator Lighting Lighting Lighting Loading the saved data of CLONING on STANDBY MODE. Orange Loading the saved data of CLONING has failed on Blinking Blinking Blinking STANDBY MODE. Orange Please refer to CLONING (66 ~ 68).
Page 122: Resetting All Settings
Troubleshooting Resetting all settings When it is hard to correct some wrong settings, the FACTORY RESET function of SERVICE item in OPTION menu (69) can reset all settings (except settings such as LANGUAGE, LAMP TIME, FILTER TIME, FILTER MESSAGE, SECURITY and NETWORK) to the factory default.
Page 123 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The signal cables are not correctly connected. 9 ~ 14 Correctly connect the audio cables. The MUTE function is working. Restore the sound pressing MUTE or VOLUME +/- button on the remote control.
Page 124 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The FREEZE function is working. Video screen display freezes. Press FREEZE button to restore the screen to normal. Color settings are not correctly adjusted.
Page 125 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page The sound When LAN, USB TYPE A or USB TYPE B port is or image selected, some ports of the output may be missing is unstable due to signal processing delay.
Page 126 Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Reference Phenomenon Cases not involving a machine defect page Disconnect the LAN cable and check that the projector When the projector is is working properly. connected to If this phenomenon occurs after connecting to the network, wired LAN, it there may be a loop between two Ethernet switching hubs...
Page 127: Olor Space Specifications
• Be sure to read “End User License Agreement for the Projector Software” which is separated document. (in the CD) DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles, IL 60174 800-676-2487 / 630-762-4032 Fax 630-584-5156 avservice@dukane.com...

This manual is also suitable for:

8105b 8106b

Dukane 8104WB User Manual

Introduction

Setting up

Remote Control

Power On/Off

Operating

Easy Menu

PICTURE Menu

IMAGE Menu

INPUT Menu

SETUP Menu

AUDIO Menu

SCREEN Menu

OPTION Menu

NETWORK Menu

SECURITY Menu

Presentation Tools

Eystone Maintenance

Olor Temp Troubleshooting

Olor Space Specifications

Quick Links

Related Manuals for Dukane 8104WB

Summary of Contents for Dukane 8104WB

This manual is also suitable for:

Table of Contents