Table of Contents
Advertisement
Programming Door Lock Pulse Length 3.5 (from .7 to 3.5 seconds)
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release
Button #3 (trunk). Press and release Button #1 (start), the parking lights will flash once, the door lock pulse length is
now 3.5 seconds. Release the brake, the parking lights will flash three (3) times. NOTE: Factory Door Lock Pulse Setting
is .7 seconds.
Programming Double Pulse Unlock "On" (Factory Security Shutdown)
(Some imports will require this setting)
Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4) times. Release Button
#4 (stop). Press and release Button #3 (trunk), the parking lights will flash once. Double Pulse Unlock is on. Release the
brake, the parking lights will flash three (3) times. NOTE: Factory Setting is Double Pulse off.
Programming Double Pulse Unlock "Off"
Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4) times. Release Button
#4 (stop). Press and release Button #3 (trunk), the parking lights will flash twice. Double Pulse Unlock is now off. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory Setting is Double Pulse off.
OPERATOR PROGRAMMING INSTRUCTIONS
Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want
to remain in programming mode. The unit will exit the programming mode simply by releasing the brake. The parking
lights will flash three (3) times confirming that you are out of programming mode.
Adding New Transmitters
Press and hold the brake, then press and hold Button #1 (start) until the parking lights flash once. Release Button #1. Press
any button on the new remote, the parking lights will flash three (3) times, the new remote is now programmed.
Programming Lock with Brake "On"
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release
Button #3 (trunk). Press and release Button #2 (lock/unlock), the parking lights will flash once. The unit will now lock
with the brake and unlock when the ignition is turned off. Release the brake, the parking lights will flash three (3) times.
NOTE: Factory setting is Lock with Brake off.
Programming Lock with Brake "Off"
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Press and
release Button #2 (lock/unlock), the parking lights will flash twice. The Lock with Brake feature is now turned off. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory setting is Lock with Brake off.
Programming Three Hour Start (Deluxe 22 only)
Press and hold the brake, then press and hold Button #2 (lock/unlock) until the parking lights flash twice. Release Button
#2 (lock/unlock). Press and release Button #1 (start), the parking lights will flash once. You are now in 3 Hour Start.
(Not available on Model Deluxe 12) Release the brake, the parking lights will flash three (3) times. Your vehicle will
start every three (3) hours. NOTE: The factory setting is Three Hour Startoff.
Programming Low Voltage Start
Press and hold the brake, then press and hold Button #2 (lock/unlock) until the parking lights flash twice. Release Button
#2 (lock/unlock). Press and release Button #1 (start). The parking lights will flash twice. Low Voltage Start is now
on. Release the brake, the parking lights will flash three (3) times. NOTE: The factory setting is Low Voltage Start
off.
Programming Three Hour Start or Low Voltage Start "Off"
Press and hold the brake, then press and hold Button #2 (lock/unlock) until the parking lights flash twice. Release Button
#2 (lock/unlock). Press and release Button #1 (start). The parking lights will flash three (3) times. Release the brake,
the parking lights will flash three (3) times. Low Voltage Start and Three Hour Start are now programmed off. NOTE:
The factory setting is Three Hour Start or Low Voltage Start off.
Programming Cold Start
Press and hold the brake, then press and hold Button #2 (lock/unlock) until the parking lights flash twice. Release Button
#2 (lock/unlock). Press and hold Button #2 (lock/unlock), the parking lights will flash once. Each continuous flash
represents a progression in degrees: one (1) flash= -40ºF, two (2) flashes=-30ºF, three (3) flashes=-20ºF, four (4)
flashes=-10ºF, five (5) flashes=0ºF, six (6) flashes=10ºF, seven (7) flashes=20ºF. To disable Cold Start, press and
hold Button #2 until the parking lights flash seven (7) times, then two (2) quick flashes 8 and 9. The Cold Start is
now disabled. Release the brake, the parking lights will flash three (3) times, the programming is now entered. NOTE:
The factory setting is Cold Start off.
Runtime Programming (Engine Off)
Press and hold Button #4 (stop) for approximately 10 seconds. The parking lights will begin to flash, each
flash represents 5 minutes of engine run time with the maximum being 15 minutes, 3 flashes (Deluxe 12) and
25 minutes, 5 flashes (Deluxe 22). Simply release button at whatever runtime you desire.
TO ENTER PROGRAMMING
10
Advertisement
Table of Contents
