Table of Contents
Advertisement
INSTALLATION PROGRAMMING INSTRUCTIONS
Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want
to remain in programming mode. The unit will exit the programming mode simply by releasing the brake. The parking
lights will flash three (3) times confirming that you are out of programming mode.
Programming Tach Start (Gasoline engines only)
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release
Button #3 (trunk). Press and release Button #4 (stop), the parking lights will flash twice. The unit is now programmed for
Tach Start. Release the brake, the parking lights will flash three (3) times. NOTE: Factory setting is Tachless Start. Now
proceed to page 20 for Tach Learning instructions.
Programming Tachless Start (Gasoline engines only)
Press and hold the brake, press and release Button #3 (trunk), the parking lights will flash three times. Press and release
Button #4 (stop) , the parking lights will flash once. The unit is now programmed for Tachless Start. Release the brake,
the parking lights will flash three (3) times. NOTE: Factory setting is Tachless Start.
Programming Diesel Start "On" (Automatically programs Tach "On")
Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4) times. Release Button
#4 (stop). Press and release Button #1 (start), the parking lights will flash once. The unit is now programmed for Diesel
Start. This automatically sets the unit to Tach mode and turns on the "glow plug input functions". Release the brake, the
parking lights will flash three (3) times. NOTE: Factory setting is Diesel Start off.
NOTE: When setting to Diesel Start, you must allow the unit to learn your vehicle's Tach signal. Procedd to Tach Learning
instructions below.
Programming Diesel Start "Off"
Press and hold the brake, then press and hold Button #4 (stop) until the parking lights flash four (4) times. Release Button
#4 (stop). Press and release Button #1 (start), the parking lights will flash twice, Diesel Start Mode is now off. Release
the brake, the parking lights will flash three (3) times. NOTE: Factory setting is Diesel Start off.
Programming Tach Learning
If your vehicle does not start properly with the preset Tach setting, press and hold the brake, then press and hold Button
#2 (lock/unlock) until the parking lights flash twice. Release Button #2 (lock/unlock). Insert ignition key and turn key to
"Run" position. (If the engine is a diesel, wait for "glow plug" light to go out.) Next, press and hold Button #4 (stop)
until the vehicle starts and runs. Release Button #4 (stop). Turn ignition key off and remove foot from brake. The parking
lights will flash three (3) times. The unit has learned your vehicle's Tach signal. NOTE: Be sure to have programmed the
unit for Tach Start before attempting to program Tach Learning.
Programming Double Crank Time "On"
(Increase crank time in tachless mode)
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release
Button #3 (trunk). Again, press and release Button #3 (trunk), the parking lights will flash once. The Double Crank Time is
now on. NOTE: Factory setting is Double Crank Time off.
Programming Double Crank Time "Off"
Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release
Button #3 (trunk). Again, press and release Button #3 (trunk), the parking lights will flash twice, Double Crank Time is
now off. Release the brake, the parking lights will flash three (3) times. NOTE: Factory setting is Double Crank Time off.
"Type C" Reverse Polarity (5-pin harness)
GREEN/BLACK Unlock
GREEN/WHITE Unlock
RED/BLACK
BLUE/BLACK Lock
BLUE/WHITE Lock
NOTE: Connect the RED WITH BLACK STRIPE wire
to +12V constant power fused at 30 amps.
NOTE: You will need to cut factory wiring to make an end to
end connection, see "Making Connections" on page 2-4.
(WE RECOMMEND THAT YOU TRY FACTORY SETTINGS FIRST)
PROCEDURE FOR ENTERING PROGRAMMING MODE
POWER
DOOR
LOCK
MOTOR
+12V
FUSE
Constant
LOCK
UNLOCK
9
Advertisement
Table of Contents
