Table of Contents
Advertisement
Quick Links
INSTALLATION GUIDE
MODELS DELUXE 12 and DELUXE 22
CONTENTS
System Features....................................................
System Components ..................................................
Tools Required.....................................................
Technical Assistance ...............................................
Before You Begin ...................................................
Precautions .......................................................
Making Connections ...............................................
Locating & Making Connections .....................................
Neutral Safety Switch ..............................................
Antenna Placement ..................................................
Connecting The 18-Pin Harness and 4-Relay Harness .................... 7
Factory Anti-Theft System...........................................
Testing Door Locks .................................................
Connecting Door Locks ..............................................
Installation Programming Instructions................................
Operator Programming Instructions ..................................
How to Use Your Remote Transmitter...............................
All tech personnel are expertly qualified to answer any technical questions.
Technicians are available Monday through Friday from 9:00 a.m. until 8:00 p.m. and Saturday 10:00 a.m. until 4:00 p.m.
OWNER'S GUIDE
REMOTE STARTER
Technical Assistance
Address
288 Canton Avenue • Wintersville, Ohio 43953
Telephone
Phone: 740-264-4710 • 800-878-8007 • Fax: 740-264-7306
•
1
1
1
1
2
2
2-4
4-6
6
7
7
8
8
9
10
10-11
Advertisement
Table of Contents
Related Manuals for Bulldog Security DELUXE 12
Summary of Contents for Bulldog Security DELUXE 12
-
Page 1: Table Of Contents
INSTALLATION GUIDE • OWNER’S GUIDE REMOTE STARTER MODELS DELUXE 12 and DELUXE 22 CONTENTS System Features............ System Components ..........Tools Required............. Technical Assistance ..........Before You Begin ........... Precautions ............Making Connections ..........Locating & Making Connections ........Neutral Safety Switch ..........Antenna Placement .......... -
Page 2: System Features
SYSTEM FEATURES 2 Four-Button Extended Range Remotely start your car to run the heater or air conditioning from an extended distance. (1 Remote Control transmitter only with Model Deluxe 12) Keyless Entry Remotely locks and unlocks your power door locks with built-in relays onboard. Ignition Controlled Door Locks A programmable feature that locks and unlocks the doors when the brake is depressed or the ignition is cycled. -
Page 3: Before You Begin
It is computer controlled and manufactured in the U.S.A. The dependability and variety of features make Bulldog Security the leader in the industry. Enjoy your new system for years to come! This system is designed to start your vehicle by sending a command signal from the remote transmitter or by programming automatic temperature or timed start. - Page 4 3. Separate the vehicle wire as shown. Make the separation large enough to fit the other wire through. 4. Insert the wire from the unit through the hole as shown. 5. Wrap the wire around one side then the other and finally around itself as shown. 6.
-
Page 5: Locating & Making Connections
4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire ties as shown. Electrical Tape Wire Tie Wire Tie Use this method ONLY when connecting two separate wires end to end. LOCATING &... - Page 6 DIESEL INSTALLATION ONLY Connecting the Glow Plug or Wait to Start Wire When installing on a diesel engine, a wire that energizes the Glow Plug (also known as the Wait to Start Wire), must be located and identified. This wire is usually located at the instrument cluster or at the ECM (electronic control module).
-
Page 7: Neutral Safety Switch
DOME LIGHT SUPERVISION (Optional Part #775 required) Before connecting the DOME LIGHT SUPERVISION, you must determine if your dome light is a (+) POSITIVE or a (-) NEGATIVE. TO TEST for a (+) POSITIVE dome light wire, clip your test light to a good solid ground, probe the dome light wire with the door closed and the dome light out, the test light should not be illuminated. -
Page 8: Antenna Placement
CONNECTING THE 18-PIN HARNESS & 4-RELAY HARNESS CAUTION: Before connecting the 18-pin harness to the module, double check all BROWN/BLACK (+) Diesel output connections to be sure they are secure GREEN/BLACK (-) Diesel output BLACK/WHITE and properly wrapped with electrical tape. Tach (-) to neg. -
Page 9: Testing Door Locks
TESTING DOOR LOCKS TESTING: Door Locks There are three basic types: “Type A” Door Lock Test (Most GMs and some Chryslers) Probe both of your door lock wires going to the door lock switch usally located in the driver’s kick panel. -
Page 10: Installation Programming Instructions
“Type C” Reverse Polarity (5-pin harness) POWER GREEN/BLACK Unlock DOOR LOCK MOTOR GREEN/WHITE Unlock RED/BLACK +12V FUSE Constant BLUE/BLACK Lock BLUE/WHITE Lock LOCK NOTE: Connect the RED WITH BLACK STRIPE wire to +12V constant power fused at 30 amps. NOTE: You will need to cut factory wiring to make an end to UNLOCK end connection, see “Making Connections”... -
Page 11: Operator Programming Instructions
Programming Door Lock Pulse Length 3.5 (from .7 to 3.5 seconds) Press and hold the brake, then press and hold Button #3 (trunk) until the parking lights flash three (3) times. Release Button #3 (trunk). Press and release Button #1 (start), the parking lights will flash once, the door lock pulse length is now 3.5 seconds. -
Page 12: How To Use Your Remote Transmitter
HOW TO USE YOUR REMOTE TRANSMITTER Starting the Vehicle with the Remote Transmitter BUTTON #1 Remote starts your vehicle. Press and release button #1 (start). The parking lights will flash once, confirming the car starter received the BUTTON #2 signal. The car will then start and the parking lights will Locks and unlocks turn on and remain on while the vehicle is running.