Using External Usb Disk For Recording - Haier LY26R3A Instruction Manual

USB MODE
Playing Music
1. After entering USB main interface,
press / to select "MUSIC".
2. Press OK to confirm the selection
and enter the music file list.
3. Press / and "OK" button to select the music you want to play
PLAY/PAUSE button to play the music.
/
Press " " to achieve the REV (fast back) and FWD (fast forward) of
played.
Press PREV/NEXT " to select the last or next music.
Press "STOP " to stop the music being played,when the current interface is the music
being played.
4. To return to the main menu just press BACK repeatedly.
NOTE: You can enjoy the music and the picture at the same time.
USB MODE
Text
1. After entering USB main interface,
press / to select Text .
2. Press OK to confirm the selection
and enter the text file list.
/
3. Press and OK" buttonto
select the text you want to play and
then press PLAY/PAUSE button to play the text .
Press PREV/NEXT " to select the last or next text.
4. To exit the Text mode just press BACK repeatedly.
NOTE: You can enjoy the music and the text at the same time.
OK
then press
the musicbeing
OK
USB MODE
Playing a Movie
1. After entering USB main interface, press
/ to select "Movie".
2. Press OK to confirm the selection
and enter the movie file list.
3. Press / and "OK" button to select the movie you want to play and then press
PLAY/PAUSE button to play the movie.
Press ZOOM to magnify the picture
Press PREV/NEXT " to select the last or next movie.
Press "STOP " to stop the movie being played.
4. To exit playing, just press BACK repeatedly.

Using External USB Disk For Recording

1. Insert the USB device with FAT32 format into the USB1
connector. Then, press MENU button.
Note: Only USB1 is available for recording.
2.Press button to select FUNCTION menu,
press button to enter .
3.Press button to select Recorder. Press OK
button to enter the submenu.
4.Press button to Select Disk and press
or OK button to enter. Press button to
select disk if your device has several disks.
5.Press button to select Format and press
enter. Press button to select the size you want
to format .Press OK button to format the USB Disk.
NOTES: The system will format the whole device and
if your device size is bigger than 1GB, you can set
the size which is used for time shift.
6.Format may take several minutes and the time is
depending on the memory size. Press
to select the Time Shift Disk Size. The max device size
for Time Shift is 8GB.Then, press OK button to save.
NOTES: If you select all the size format for time shift,
you can not do any recording.
7.Waiting for the system checking. And you can see the speed
data after the success checking.
NOTES:
1. Only have to format when you use the device for record for the first time.
2. The minimum device size for record is 1GB. Provide device formatting function
is up to 2TB. The max Multi-Partition is 16 partitions and one is active at a time.
3. Bit rate:
Device bit-rate>4.5MB/s REC is safe at HD stream
Device bit-rate>1.5MB/s REC is safe at SD stream
Device bit-rate<600KB/s REC is bad for REC
4. The system can not work normally if the USB device have the listing problem
below:
The device has bug.
The device has error block.
The device reports the unfaithful size.
IMPORTANT : USB device should be format as FAT32 format by
your PC before insert to the USB connector.
OK
Menu
Ok
Select Disk USB1 C:
Check File System Ok start
USB Disk
Ok
Format
Time Shift Size
Speed
File System Size
to
File System Size All
SD 27Min HD7Min
OK CANCEL
Format
Do not unplug USB device
Formating.....
button
Time Shift Size
Time Shift Size All
SD 14Min HD4Min
OK CANCEL