Oki OKICOLOR8n Hardware Installation Manual
Flash simm kit
Hide thumbs
Also See for OKICOLOR8n:
- Replacement instructions (4 pages) ,
- Installation instructions (1 page) ,
- Handy reference (60 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Setup Manual
Advertisement
Table of Contents
Related Manuals for Oki OKICOLOR8n
Summary of Contents for Oki OKICOLOR8n
- Page 1 Hardware Installation Guide: English...
-
Page 2: Year 2000 Compliance
Written and produced by the Oki Data Training and Year 2000 Compliance Publications Dept. Please address any comments to: Training and Publications Department All products currently sold by Oki Data are Year 2000 Oki Data Americas, Inc. Compliant. Each product contains information technology 2000 Bishops Gate Blvd. -
Page 3: Table Of Contents
Contents Overview Introduction ..............4 Kit contents ................4 Installing Flash Memory in the OKIPAGE® 10i, 10i/n, 10e, 10ex, 12i and 12i/n Printers ....5 Preparing Your Printer ............5 Removing the Access Plate ............ 6 Installing the SIMM Card ............6 Installing the Board .............. -
Page 4: Introduction
Kit contents switched off. Kit # 70035701 Use the OKI Image Creator and NetFlash software utilities on · 4 MB Flash SIMM card the CD included in this kit, to download flash memory fonts · CD and macros, etc. -
Page 5: 10I/N, 10E, 10Ex, 12I And 12I/N Printers
Installing Flash Overview If your printer is not equipped with one of these accessories, you will need to purchase the accessory to install the Flash Memory in the SIMM in the printer. Expansion sockets are provided on each board included in the option kits. OKIPAGE 10i, 10i/n, ®... -
Page 6: Removing The Access Plate
2 Remove the SIMM card from its packaging. 3 Hold the SIMM card with the metallic contact edge down, and the notch on the bottom. 4 Insert the metallic contact edge of the SIMM card into the SIMM 2 socket at a 45° angle. OKI Flash SIMM... -
Page 7: Installing The Board
5 Push in until the metallic contacts are fully inserted into 2 Insert the option board into the printer, making sure that it the socket. locates in the guide rails. Slide in the board and push it firmly into place. 6 Push the SIMM card forward slightly until it snaps into place. -
Page 8: Installing Flash Memory In The Okipage 20, 20Dx And 20Dxn Printers
Preparing Your Printer The OKIPAGE 20/20DX has three slots for installation of 1 Turn printer off and unplug power cord. optional SIMMS: 2 Detach the interface cable. SIMM 3 Push the OPEN button, then open the top cover. sockets OKI Flash SIMM... -
Page 9: Installing The Simm Card
4 Remove and save the two large screws on the right side, 6 Remove and save the two screws on the left of the metal which hold the side panel in place. plate covering the internal board, then pull the plate out about an inch and lift it out. - Page 10 SIMM at the bottom. Push in until the two mounting screws. the silver contacts are fully inserted into the socket. 3 Pivot the SIMM to the left until it snaps into place. OKI Flash SIMM...
- Page 11 5 Replace the side panel (tabs go in slots): you’ll need to 6 Secure the panel in place with the two screws. move the cover hinge out of the way before you put the side panel back into place. 7 Close the printer cover. Hardware Installation Guide: English...
- Page 12 8 Reattach the interface cable and plug the power cord into the power outlet. OKI Flash SIMM...
-
Page 13: 24Dx And 24Dxn Printers
Installing SIMMs Installing Flash Overview Memory in the Preparation 1 Turn the printer off. OKIPAGE 18, 18n, 24DX and 24DXn Printers CAUTION! Circuit boards can be damaged by static electricity and rough handling. Keep board in packaging until you’re ready to install it. SIMMs are sensitive to static electricity. - Page 14 2 Unplug the power cord and detach the interface cable from the back of the printer. 4 Remove and save the two large screws (1) on the right side, which hold the side panel in place. 3 Push the OPEN button, then open the top cover. OKI Flash SIMM...
- Page 15 5 Pull the side panel out and remove it from the printer, then 6 Remove and save the screws on the metal plate covering close the cover to protect the image drum from light while the internal board, then lift the plate out. you are installing the SIMM.
-
Page 16: Installing The Simms
1 Locate the SIMM sockets on the board. The top socket (1) is used for a Flash SIMM. 3 Angle the SIMM down about 45°, then insert the contact edge into the top socket and lift the board until it locks in place. OKI Flash SIMM... -
Page 17: Finishing The Installation
Finishing the Installation 2 Open the cover and replace the side panel (tabs go in slots): you need to move the cover hinge (1) out of the 1 Position the metal plate on the housing and replace the way. mounting screws. Hardware Installation Guide: English... - Page 18 3 Secure the panel in place with the two screws (1). 5 Reattach the PC interface cable and plug the power cord into the power outlet. 4 Close the printer cover. OKI Flash SIMM...
-
Page 19: Software Utilities Installation
Software Utilities Overview Installation To install the Image Creator and NetFlash utilities: 1 Insert the Flash SIMM Kit CD into your CD-ROM drive. 2 Click Start – Run. 3 Type D:\SETUP (if your CD-ROM drive exists at other than D, use the appropriate letter). 4 Follow the installation instructions.