Oki OKICOLOR8 Setup Manual
Oki OKICOLOR8 Setup Manual

Oki OKICOLOR8 Setup Manual

Okicolor 8 series setup guide
Hide thumbs Also See for OKICOLOR8:

Advertisement

<div class="page-bg-wrapper"><div style="height: 950px; top: 0px; background-image: url(https://ct-static-data2.manualslib.com/ctic/ci10/50/4933/493213/okicolor8_1-1_crop0_bg.png)" class="page-bg-image">
Overview
1 Unpack ........................................ 1
3 Install the Oil Roller ................ 5
6 Load paper ................................. 8
8 Connect to Power ..................... 9
9 Print the Demo Page ............... 9
10 Install Software ........................ 9
11 Calibrate the Color ................. 10
1
Unpack

Select a Location

• Firm, level surface capable of supporting
at least110 lbs (50 kg).
• Clearance to open cover, paper tray and
Special Media Stacker (rear exit)
• At least 4 inches (102 mm) additional
clearance on both sides
• Nearby power source
• Room temperature:
-
Ideal: 62.6 to 80.6ºF (17 to 27ºC):
-
Maximum Permissible: 50 to 89.6ºF
(10 to 32ºC)
• Relative humidity:
-
Ideal: 50 to 70% RH
-
Maximum Permissible: 20 to 80% RH
• Away from direct sunlight
Remove the accessory tray
and check the contents
• Toner cartridges
(1 each: black,
magenta, cyan,
yellow)
• Toner Waste Box
• Oil Roller
• CD
• Image Drum Storage
Bags (4) and
Lens Cleaners (4)
• Power Cord
<div class="page-bg-wrapper"><div style="height: 950px; top: 0px" data-src="https://ct-static-data2.manualslib.com/ctic/ci10/50/4933/493213/okicolor8_1-3_crop0_bg.jpg" class="lazyReady page-bg-image loading background-css">
Remove Packaging
The printer weighs approximately 106
!
lb (48 kg). Use a least two (2) people to
carry the printer. Use appropriate lifting
techniques.
1 Remove the top cushions.
2 Lift the printer from the box and place it
on a suitable support.
3 Remove it from the plastic bag.
4 Remove the shipping tape.
5 Remove the control panel protective film.
6 Open the front tray and pull out the
shipping retainer, then close the tray.
|
Page 1

Advertisement

Table of Contents
loading

Summary of Contents for Oki OKICOLOR8

  • Page 1: Table Of Contents

    Remove Packaging Overview Remove the accessory tray and check the contents The printer weighs approximately 106 1 Unpack ........1 lb (48 kg). Use a least two (2) people to 2 Install the Toner Waste Box ... 4 carry the printer. Use appropriate lifting 3 Install the Oil Roller ....
  • Page 2: Install The Toner Waste Box

    Install the Toner Make sure the drive coupling on the 4 Close the side panel. toner waste box is lined up with the Waste Box coupling on the printer. 1 Remove toner waste box from packaging. 2 Pull the latch and open the side panel. Remove any blue shipping retainers.
  • Page 3: Install The Oil Roller

    Install the Oil 4 Remove the shipping tape from the blue 7 Lower the right end into the fuser unit. levers. Make sure the levers are pulled Roller forward. 1 Remove the oil roller packaging. 2 Turn it over and look at the gear end: if you 8 Pull the blue lock lever forward to lock the 5 Make sure the blue lock lever is toward the see a blue shipping retainer, remove it.
  • Page 4: Prepare The Image Drums

    Prepare the 2 Carefully remove the shipping tape and 4 Place the image drums back into the sponge insert from each drum. You may printer, matching the color coded label Image Drums want to do this holding the drum over a with the label in the printer.
  • Page 5: Install The Toner Cartridges

    Install the Toner 4 Placing the left end under the color tab, 6 Repeat steps 5 and 6 for the three insert the toner cartridge into the remaining toner cartridges. Cartridges corresponding color image drum. Be careful to install each color toner 7 Remove the protective paper from all four cartridge in the corresponding color image drum (C=cyan, M=magenta,...
  • Page 6: Load Paper

    Connect to Load Paper 4 Insert paper and push in the tray. Your Computer 1 Pull out the tray and remove the shipping The printer interface cable is not supplied. insert. PC Systems You need: • A shielded IEEE-1284 parallel Shipping insert bidirectional interface cable, maxiumum length 6 ft.
  • Page 7: Connect To Power

    Connect to Install Software 2 On the printout, under ETHERTALK, Printer Name, note the name that appears, Power for example, OKI_465987. You will need Windows 95/98/NT4.0 this name for step 5. 3 Activate Chooser from the Apple menu. 1 Connect the power cord. 1 Insert the OKICOLOR 8 CD into your CD 4 Locate and select the AdobePS icon.
  • Page 8: Calibrate The Color

    Calibrate the Windows and Macintosh Windows 95/98/NT4.0 4 Click Print Color Calibration page. Open the Color Registration Utility. Color The printer prints a test page with 9 Click Start ® Programs ® sections, each with a series of lined boxes OKICOLOR 8 ®...
  • Page 9: Setting The Color Balance

    Setting the Color Balance 6 On the screen, find the corresponding box Look at the Color Balance Adjustment Page: (in this case, #1—yellow, left) and enter • The pattern consists of a series of Windows and Macintosh the number you noted on the calibration rectangles on a gray background.
  • Page 10: Control Panel

    Control Panel Status Printer Language Buttons Low Toner Indicators Paper Size Paper Source Buttons The control panel buttons are dual function: press and release to engage the top function; press and hold for 2 to 3 seconds to engage the bottom function. Press: Changes printer status from on line to off line.
  • Page 12: Energy Star

    Registered Trademark ® , Heidelberger Druckmaschinen AG, used responsibility for the results of errors beyond its control. Oki Data also cannot guarantee that changes in software and equipment made under license. All rights reserved and unauthorised use or by other manufacturers and referred to in this guide will not affect the reproduction is prohibited.

This manual is also suitable for:

Okicolor8cccsOkicolor8nOkicolor 8

Table of Contents