Advertisement
Install the water inlet hose
Confirm the water faucet
Water faucet,suitable
Outlet end surface
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
water inlet hose jointer
Slider
Screw knife
Lock level
water inlet hose
Figure 1
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 4
Water faucet,not suitable
Screw
Sign plate
Bushing
Figure 2
Figure 3
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 5
Figure 6
Child lock function
Reserve, remain time digitron
The function is intended for children safety and preventing the washing
program from accidental changes by children.
It displays "--" during detecting.
Push and hold the reserve button and spin button, then push down the
It displays remained reserve time (hour).
power on/off button .The digitron displays C L .You can continue setting
It displays total remained time (min). If the total time
desired washing procedures. After setting ,push down the start/pause
exceeds 99 minutes, it uses "A" on tens digit to
button. The child lock function is activated. all of the buttons are locked
represent100 minutes, and uses "b" to represent 110
and cannot make selecti o n .
minutes. E.g. "A3" represents 103 minutes.
Release the child l o ck function :push down reserve button and spin
button at the same time for more 2seconds .After a beep sound ,the child
It displays abnormal symbol in abnormal situation.
lock function is released.
(See to Page15)
STANDARD
WOOLLEN
CARPETING
SAVING
WATER
PROGRAM
RESERVE
WATER LEVEL
"
WATER LEVEL button
"
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among
4, 6, 8,and 10 automatically.
You can also set water level by yourself. After the machine is
started, it will not set water level automatically. You shall push the
start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the
laundries and will display water level 6 .If wet laundries are put
in, it may display water level A. You must set suitable water level
by yourself.
If posthaste program is selected, it will display water level 3 .
When water level 2 is reached in water filling, it will perform
washing while filling water. When water level 3 is reached, it will
change to normal washing.
During operation of wash and rinse program, you can push down
the water level button to add water. When you release the button, or
it reaches the overflow water level, the machine will stop adding
water.
The water level decided may be different from actual value because
of the different moisture level of the laundries.
All the program that When water level 1 is reached,it will perform
washing while filling water.When water level set is reached, it will
change to normal washing.
You can set posthaste woollen carpet water saving program
by yourself, never changed. It is to set water level 8 highest during
the standard program.
Attention A delegates 10
"POWER" button
Push the "POWER" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "POWER" button to switch on the power. If
the "START/PAUSE" button is not pushed, the machine
COMMON
will switch off the power automatically after 5 minutes.
QUICK WASH
POSTHASTE
JEAN
POWER
ON/OFF
"PROGRAM" button
"
RESERVE button
"
Following full-auto program is available
The digitron displays the time
Program
Application
remained (in minute) before
Standard
the washing is finished.
Standard saving washing for normal laundries
Normal
Washing for normal laundries
Push down the reserve
button. The reserve indicator
Quick
Quick washing for normal laundries
light is on the digitron displays
Posthaste
Washing for light-soil
a few laundries
the reserve time of finishing
washing (in hour).The time
Jean
Washing for big and thick laundries
remain indicator light is on,
indicating that the reserve
Woollen
Washing for the woollen laundries,
under 2.5kg
function is running.
Carpet Washing for carpet and wearing bigger
Push the reserve button can
Laundries, under 3.0kg
display the reserve state.
Saving
Saving washing for light-soil laundries
water
Advertisement
