Related Manuals for Haier HWM96-0613S
Summary of Contents for Haier HWM96-0613S
- Page 1 Twin-tub Washing Machine User's manual This manual is for HWM96-0613S Please read this manual carefully before using. Retain it for future reference. 0030802762D...
-
Page 2: Table Of Contents
Contents Names of the parts Safety precautions Installation and adjustment Preparation before washing The musts in washing Usage of the detergent Washing sequence Disposal after washing Trouble-Shooting *Answers to question Packing list Specification... -
Page 3: Names Of The Parts
¸ ÷ ² ¿ Î » Ã û ³ Æ Names of the parts Outer cover of the spin tub Water-filling entrance Water inlet selector handle Inner cover of the spin tub Wash selector Spin timer Wash timer Spin tub frame Control panel Spin tub Overflow filter... -
Page 4: Safety Precautions
× ¢ Ò â Ê Â Ï î Safety precautions Please insert the power cord into When the machine is normally special receptacle with rated vol- using, please put the power plug tage.Be sure to use single-phase at the location easily to be insert- three pins receptacle.The earthing ed and extracted by hand. - Page 5 Safety precautions × ¢ Ò â Ê Â Ï î Do not stretch hands into the working Do not decompose, repair or alter the machine. It is dangerous even if the machine by yourself. rotation is slow. Take special care of the children.
-
Page 6: Installation And Adjustment
Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. Install the lint filter After opening the package, please take out the lint filter from the document bag, install it to the overflow filter of the wash tub. -
Page 7: How To Change The Direction Of The Drain Hoses
How to change the direction of the drain hoses Figure 1 indicates the leave factory Back installation position of the drain hose. Soft item Front Extend the drain hose from the side of wash tub Figure 1 Put soft items on the ground. Lean the machine down gently with the front surface facing the ground. -
Page 8: Install The Water Inlet Hose; Select The Water Level
Install the water inlet hose; Select the water level Insert the water inlet hose into the water-filling entrance on the control pane directly.(pull it out to dismantle it) Water inlet hose Water inlet Select water level according to the quantity of the laundries. Water level Set the water level adjusting lever indicator... -
Page 9: Preparation Before Washing
Ï ´ Ç ° × ¼ ± ¸ Preparation before washing Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. -
Page 10: The Musts In Washing
The musts in washing Ï ´ µ Ó Ð ë Ö ª The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. -
Page 11: Washing Sequence
Ï ´ µ Ó Ë ³ Ð ò Washing sequence Water-filling selector handle Overfilling sign Spin timer Wash timer Wash selector Water-filling entrance (to set to below 1 minute, (To set to below 2 minute, (Strong current, first set to 2 minute then standard current) first set to 5 minute then turn it back. - Page 12 Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push Proper Proper The laundries No gland are slanting (2) Close the inner and outer cover of the spin tub.
-
Page 13: Rinse With Water-Filling
Rinsing Rinse with water-filling OVERFILL 1.Put the laundries into the wash tub. Select suitable current according to the laundries. If you find water flo- wing out here,please twist the water tap to 2.Adjust the water level limit the water filling. Set the water level with water level adjusting lever according to the laundries quantity. - Page 14 Spinning 1. Put the laundries into the spin tub evenly and smoothly. Selection of the spin time Spin time Laundries (minutes) 2. Press the gland in the tub properly. Bed sheet or Close the inner and outer cover of About 4~5 blanket the spin tub.
-
Page 15: Disposal After Washing
Ï ´ º ó ´ ¦ À í Disposal after washing After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. -
Page 16: Cleaning The Overflow Filter
Ï ´ º ó ´ ¦ À í Cleaning the overflow filter 2. Take off the corrugation pipe. Water level Dismantle the upper part of the adjusting lever corrugation pipe inside overflow filter ( as indicated in Corrugation Figure 1). Pipe 3. -
Page 17: Trouble-Shooting *Answers To Question
Trouble-shooting Answer to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub, please take them out immediately. 1.Dismantle As indicated in the figure, push the point marked Spin tub frame with "... - Page 18 Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company.
-
Page 19: Packing List
× ° Ï ä Ë µ Ã ÷ Packing list Quantity Name One piece User's manual One piece Water inlet hose One piece Lint filter Water-filling jointer One piece One piece Gland One set Twin-tub washing machine... -
Page 20: Specification
Specification Maximum/43L Medium/36L Minimum/30L Water level/Water quantity (about) Injection pressure(MPa) 0.02 0.2...