Using Traceroute And Traceroute Ipv6 Commands - Cisco AP776A - Nexus Converged Network Switch 5020 Configuration Manual

Chapter 2 Before You Begin
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
Table 2-3
Option
Type of service
Set DF bit in IP header
Data pattern
The syntax for this command is as follows:
switch# ping
Target IP address: 198.133.219.25
Target IP address: 198.133.219.25
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface:
Type of service [0]:
Set DF bit in IP header [n]:
Data pattern [0xABCD]:
Sweep range of sizes [n]:
PATTERN: 0xabcd
PING 198.133.219.25 (198.133.219.25) 100(128) bytes of data.
108 bytes from 198.133.219.25: icmp_seq=1 ttl=245 time=0.600 ms
108 bytes from 198.133.219.25: icmp_seq=2 ttl=245 time=0.614 ms
108 bytes from 198.133.219.25: icmp_seq=3 ttl=245 time=0.872 ms
108 bytes from 198.133.219.25: icmp_seq=4 ttl=245 time=0.558 ms
108 bytes from 198.133.219.25: icmp_seq=5 ttl=245 time=0.570 ms
--- 198.133.219.25 ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 7996ms
rtt min/avg/max/mdev = 0.558/0.642/0.872/0.120 ms
To abnormally terminate a ping session, type the Ctrl-C escape sequence.

Using traceroute and traceroute ipv6 Commands

Use the traceroute command to print the routes taken to reach a specified host or IP address.
The IPv4 syntax for this command is traceroute host or traceroute ipv4-address.
switch# traceroute www.cisco.com
Tracing route to www.cisco.com [198.133.219.25] 30 hops max, 38 byte packets
1
2
3
4
5
6
7
8
OL-18084-01, Cisco MDS NX-OS Release 4.x
Options and Defaults for the ping and ping ipv6 Commands (continued)
Description
The quality of service (QoS) in Internet Control Message
Protocol (ICMP) datagrams (see the
page
The Path MTU Discovery strategy (see the
the MTU Frame Size" section on page
You may specify up to 16 bytes to pad the outgoing packet.
This padding is useful when diagnosing data-dependent
problems in a network. For example,
packet with all ones.
bras3-l0.pltnca.sbcglobal.net [151.164.184.79] 30 ms
dist2-vlan50.pltn13.pbi.net [64.164.97.67] 20 ms
bb2-g1-1.pltn13.pbi.net [67.116.251.194] 20 ms
bb1-p12-0.pltn13.pbi.net [151.164.40.17] 20 ms
bb2-p13-0.sntc01.pbi.net [151.164.191.65] 20 ms
ex1-p3-0.eqsjca.sbcglobal.net [64.161.1.54] 20 ms
sl-st20-sj-0-0.sprintlink.net [144.223.242.81] 20 ms
sl-bb25-sj-10-0.sprintlink.net [144.232.20.62] 20 ms
56-3).
Cisco MDS 9000 Family CLI Configuration Guide
Using traceroute and traceroute ipv6 Commands
"QoS" section on
"Configuring
46-3).
fills the outgoing
ff
30 ms 20 ms
20 ms 30 ms
20 ms 20 ms
21 ms 20 ms
20 ms 30 ms
20 ms 30 ms
20 ms 30 ms
30 ms 20 ms
Default
0
No
0xABCD
2-17