Control Stations; Mounting Brackets - Chamberlain GH User Manual

ACCESSORIES
REMOTE CONTROLS 315MHz
371LM
1-Button SECURITY✚
Includes visor clip.
373LM
3-Button SECURITY✚
Includes visor clip.
333LM
3-Button Tri-Colored Dip Switch Remote Control
Includes visor clip.

CONTROL STATIONS

02-101
1-Button Control Station:
Steel enclosure.
02-102
2-Button Control Station
Steel enclosure.
02-103L
3-Button Control Station:
OPEN
Steel enclosure with Maintenance Alert System.
CLOSE
STOP
02-110 Key Control Station:
Indoor flush mount, NEMA 1 with Stop button.

MOUNTING BRACKETS

10-12360 Heavy gauge steel bracket for vertical or horizontal mount
on either front or top of coil on a rolling door. Has a variety
of mounting hole patterns compatible with many OEM
manufacturers. May be welded. For use with J, H, DJ, and
DH operators.
Cast iron bracket to mount J, H, DH, DJ, and GH side mount
08-9098
operators on end bracket of a rolling door or grill. For
vertical or horizontal mount on either front or top of coil.
Same as 08-9098, but with adapter plate to hold mounting
08-9098EZ
bolt holes in place for ease of use.
Heavy gauge steel bracket for vertical or horizontal mount
1A4324
on either front or top of coil on a rolling door. May be
welded. For use with J, H, DJ, and DH operators.
1A4324EZ Same as 1A4324, but with adapter plate to hold mounting
bolt holes in place for ease of use.
MISCELLANEOUS
1A3982 Operator Cover:
For use with wall-mounted J, H, GH, DH or DJ operators.
Measures 31" x 19" x 18" (L x W x D). Assembly required.
Recommended for damp environments where direct spray
is present. Required when the operator is installed less
than 8 feet above the floor.
86LM (15')
Antenna Extension Kit:
86LMT (25')
The antenna extension kit can be used with EXT-ANT for
maximum radio receiver range.
® Remote Control:
® Remote Control:
:
:
ENTRAPMENT PROTECTION DEVICES
CPS-UN4
Commercial Protector System
Provides protection on doors up to 45' wide. NEMA-4
rated.
CPS-U
Commercial Protector System
Provides protection on doors up to 30' wide.
Option Logic Board:
CPS3
For use when more than one set of photoelectric eyes are
required.
CPS-EI
CPS-EI
Monitored Safety Edge Interface:
E1
LMEP2
E2
LMEP1 For use with the approved 4-wire safety edge (see below).
E3
E4
40-34141-1
65ME1234
Miller ME123 4-Wire Monitored Safety Edge:
For sectional or rolling doors.
65ME110
Miller ME110 4-Wire Monitored Safety Edge:
For rolling grilles and counter shutters.
NON-MONITORED
65-8202
Vehicle Detection System:
Pneumatic Sensing Edge Kit with exterior air switch, 2-wire
coil cord and 14' air hose.
65-5202
Vehicle Detection System:
Pneumatic Sensing Edge Kit with exterior air switch, 2-wire
take-up reel (20' extended) and 14' air hose.
TLSCARD
Timer Light Status Card:
The TLS option card provides special functionality to
activate and flash auxiliary devices such as lights, bells, and
horns/strobes at various door positions, and to provide
special timer functions.
AUXCARD
Auxiliary Contact Card:
The Auxiliary Contact option card has both Normally-Open
and Normally-Closed contacts that actuate when the door is
idle, opening, or closing.
MOUNTING CHANNELS
65ME123C
U-Shaped Mounting Channel:
For 65ME1234 edge when installed on sectional doors.
65ME123C1
T-Shaped Mounting Channel:
For 65ME1234 edge when installed on rolling doors. Fits
between L-shaped angles used to construct a bottom bar
on rolling doors.
65ME123CA3
L-Shaped Mounting Channel:
For 65ME1234 edge when installed on sectional doors.
CHAIN TENSIONERS
For 1" shafts. Recommended to properly tension drive chain
71-6023
between operator shaft and door shaft.
Same as 71-6023, but for 1-1/4" shafts.
71-6125
11
MONITORED
® :
® :
For Jackshaft Type Operators