Related Manuals for NETGEAR GSM7352SNA - Prosafe 48 Port Gigabit L3 Managed Stackable Switch
Summary of Contents for NETGEAR GSM7352SNA - Prosafe 48 Port Gigabit L3 Managed Stackable Switch
-
Page 1: Installation Guide
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Installation Guide NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 202-10255-01 February 2007... - Page 2 In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein.
- Page 3 EN 55 022 Declaration of Conformance This is to certify that the NETGEAR ProSafe™ 24-Port 10/100/1000 L3 managed Stackable Switch with 4 10 Gigabit I/ O Slots GSM7328S is shielded against the generation of radio interference in accordance with the application of Council Directive 89/336/EEC, Article 4a.
- Page 4 Refer to the Support Information Card that shipped with your Managed Stackable Layer 3 Fast Ethernet Switch. World Wide Web NETGEAR maintains a World Wide Web home page that you can access at the universal resource locator (URL) http://www.netgear.com. A direct connection to the Internet and a Web browser such as Internet Explorer or Netscape are required.
-
Page 5: Table Of Contents
Contents Chapter 1 About This Manual Audience, Conventions, Formats, and Scope ..............1-1 How to Use This Manual ....................1-2 How to Print this Manual ....................1-3 Revision History ......................1-4 Chapter 2 Introduction GSM7328S Front Panel and LEDs .................2-1 GSM7328S Rear Panel ....................2-4 GSM7352S Front Panel and LEDs .................2-4 GSM7352S Rear Panel ....................2-6 GSM7328FS Front Panel and LEDs ................2-7... - Page 6 Connecting Equipment to the Switch ................3-10 RJ-45 Ports ......................3-10 Connecting a Console to the Switch ................3-11 Chapter 4 Troubleshooting Troubleshooting Chart ....................4-1 Additional Troubleshooting Suggestions ...............4-2 Appendix A Technical Specifications Appendix B Default Configuration Settings v1.0, February 2007...
-
Page 7: About This Manual
Chapter 1 About This Manual The Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Installation Guide describes installation and basic troubleshoting for the NETGEAR ® GSM7328S and GSM7352S switches. Audience, Conventions, Formats, and Scope This information in this guide is intended for network managers familiar with network management concepts and terminology. -
Page 8: How To Use This Manual
Stackable Switch with 4 10-Gigabit Slots GSM7328FS Manual Publication Date February 2007 Note: Product updates are available on the NETGEAR, Inc. Web site at http://kbserver.netgear.com/downloads_support.asp. How to Use This Manual The HTML version of this manual includes the following: •... -
Page 9: How To Print This Manual
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- How to Print this Manual To print this manual, you can choose one of the following options, according to your needs. • Printing a Page from HTML. Each page in the HTML version of the manual is dedicated to a major topic. -
Page 10: Revision History
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Revision History Part Number Version Publication Date Description 201-10813-01 March 2006 Document Created. 202-10255-01 February 2007 Added description of GSM7328FS switch. About This Manual v1.0, February 2007... -
Page 11: Introduction
Chapter 2 Introduction The NETGEAR Layer 3 Managed Stackable Fast Ethernet Switch is a state-of- the-art, high-performance, IEEE-compliant network solution. It includes powerful management features that you can use to eliminate bottlenecks, boost performance, and increase productivity. This guide describes hardware installation and basic troubleshooting for the following NETGEAR switches: •... - Page 12 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- RJ-45 jacks Copper/fiber Stacking/XFP LEDs combo ports module bays (reset button) Figure 2-1 The following table describes the LEDs on the front panel of the switch. Table 2-1. LED Descriptions for GSM7328S Description This is the stack member ID (1–8) that the software assigns to the switch.
- Page 13 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Table 2-1. LED Descriptions for GSM7328S (continued) Description M1, M2, M3, M4 XFP Module present or Stacking Adapter present and ACT LED: High-Speed I/O XFP Module present LED /ACT Modules •...
-
Page 14: Gsm7328S Rear Panel
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- GSM7328S Rear Panel The rear panel has two module bays, a console port, redundant power supply connector, and a standard AC power receptacle for the supplied power cord. The module bays support any combination of either the ProSafe 10-Gigabit Ethernet XFP Adapter (AX741) or the ProSafe 24-Gigabit Stackable Module (AX742). - Page 15 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- The table below describes the GSM7352S LEDs on the front of the switch. Table 2-2. GSM7352S LED Description Description This is the stack member ID (1–8) that the software assigns to the switch.
-
Page 16: Gsm7352S Rear Panel
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Table 2-2. GSM7352S LED Description (continued) Description M1, M2, M3, M4 XFP Module present or Stacking Adapter present and ACT LED High-Speed I/O XFP Module present LED /ACT Modules •... -
Page 17: Gsm7328Fs Front Panel And Leds
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- GSM7328FS Front Panel and LEDs The following figure shows the front panel of the GSM7328FS. The front panel contains LEDs, a RST (reset) button, RJ-45 jacks, copper/fiber combo ports, and two module bays. - Page 18 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Table 2-3. LED Descriptions for GSM7328FS Description Power /Status LED • Solid Green: Power is supplied to the switch and it is operating normally • Solid Yellow: POST in progress Blinking Yellow: POST / CPU system / Internal Power Supply failure •...
-
Page 19: Gsm7328Fs Rear Panel
• Blinking Green: Packets transmission or reception is occurring on the port RPS LED • Solid Green: NETGEAR RPS Bank connected (Using internal Power) • Solid Yellow: The Switch internal power has failed or been disconnected , but the RPS is providing power to switch •... -
Page 20: Safety Instructions
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Safety Instructions Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential damage. To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions. - Page 21 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- • To help avoid damaging your system, be sure that the voltage selection switch (if provided) on the power supply is set to match the power available at your location: –...
- Page 22 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- 2-12 Introduction v1.0, February 2007...
-
Page 23: Hardware Installation
Configuration software – Documentation including the Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches, the NETGEAR 7000 Series Managed Switch Administration Guide, the NETGEAR Installation Guide for the 7000 Series Stackable Managed Switch, and this Hardware Installation Guide •... -
Page 24: Protecting Against Electrostatic Discharge
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Protecting Against Electrostatic Discharge Warning: Static electricity can harm delicate components inside your system. To prevent static damage, discharge static electricity from your body before you touch any of the electronic components, such as the microprocessor. -
Page 25: Installation
4. Make sure that all items are present. See “Package Contents” on page 3-1. Note: If any item is found missing or damaged, contact your local NETGEAR reseller for replacement. 5. Inspect the products and accessories for damage. Report any damage immediately. -
Page 26: Select A Location
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Select a Location The switch can be mounted in a standard 19-inch (48.26-centimeter) rack, wall- mounted, or left freestanding (placed on a tabletop). The site where you install the switch may greatly affect its performance. Before installing the switch or switches, make sure that the chosen installation location meets the following site requirements. -
Page 27: Install The Switch
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Install the Switch You can install the switch on a flat surface or in a standard 19-inch rack. Installing the Switch on a Flat Surface The switch ships with four self-adhesive rubber footpads. Stick one rubber footpad on each of the four concave spaces on the bottom of the switch. -
Page 28: Check The Installation
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- 4. Align the bracket and rack holes. Use two pan-head screws with nylon washers to fasten each bracket to the rack. 5. Tighten the screws with a No. 2 Phillips screwdriver to secure the switch in the rack. -
Page 29: High-Speed I/O Module Bays
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- High-Speed I/O Module Bays The High-Speed I/O Module Bays can be used for inter-switch stacking or to install XFP 10-Gigabit Ethernet modules. If you want to do both, you can stack the switch using two 24-Gigabit Stackable Modules (AX742), and then use the remaining module bays for 10-Gigabit Ethernet XFP Adapters (AX741). - Page 30 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- To install additional Gigabit Ethernet modules, repeat step 1. High-Speed I/O Module Installation The High-Speed I/O Module Bays support ProSafe 10-Gigabit Ethernet XFP Adapter (AX741) or ProSafe 24-Gigabit Stackable Modules (AX742). AX741 adapter Figure 3-3 When the ProSafe 10-Gigabit Ethernet XFP Adapter (AX741) is in place, you can...
-
Page 31: Stacking
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Stacking You can connect up to eight switches to form a stack with a single management IP address. The switches automatically select a master unit. Once the master is selected, you can use its console to manage all the switches in the stack. -
Page 32: Connecting A Redundant Power Supply
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Connecting a Redundant Power Supply Each switch has a redundant power supply (RPS) connector at the rear of the switch next to the power receptacle. Power receptacle Redundant power supply connector Figure 3-6 You can connect an external DC-to-DC power supply unit to the switch to provide... -
Page 33: Connecting A Console To The Switch
Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Connecting a Console to the Switch After you install the switch and apply power, you can connect to it with a terminal or workstation. You can use the Command Line Interface (CLI) to identify the IP address. - Page 34 Command Line Interface Reference for the ProSafe 7300S Series Layer-3 Stackable Switches: Gives detailed examples of how to use the CLI, and is located on the Resource CD. • NETGEAR 7000 Series Managed Switch Administration Guide: Describes configuration tasks, and is located on the Resource CD. 3-12 Hardware Installation...
-
Page 35: Troubleshooting
Chapter 4 Troubleshooting Troubleshooting Chart The following table lists symptoms, causes, and solutions of possible problems. Table 4-1. Troubleshooting Chart Problem Cause Solution Power LED is off. No power is received Check the power cord connections for the switch at the switch and the connected device. -
Page 36: Additional Troubleshooting Suggestions
You can verify the integrity of the switch by resetting the switch. To reset the switch, use the Tools> Reset command or remove AC power from the switch and then reapply AC power. If the problem continues, contact NETGEAR technical support. -
Page 37: Technical Specifications
Appendix A Technical Specifications This appendix provides technical specifications for the switches. Table A-1. Technical Specifications Feature GSM7328S GSM7352S GSM7328FS IEEE Network 802.3 10BASE-T Protocol and 802.3u 100BASE-TX Standards 802.3z 1000BASE-SX compatibility 802.3z 1000BASE-LX 802.3ab 1000BASE-T 802.3ae 10000BASE-LR 802.3ae 10000BASE-SR 802.3x flow control Switch •... - Page 38 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Table A-1. Technical Specifications (continued) Feature GSM7328S GSM7352S GSM7328FS Layer 2 • 802.1Q Static VLAN (Up to 4k) Services • 802.1p Class of Service (CoS) • 802.1D Spanning Tree Protocol (STP) •...
- Page 39 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Table A-1. Technical Specifications (continued) Feature GSM7328S GSM7352S GSM7328FS Performance • Forwarding modes: Store-and-forward • Network latency: Less than 80 microseconds for 64-byte frames in store-and-forward mode for 10 Mbps to 100 Mbps transmission •...
- Page 40 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Technical Specifications v1.0, February 2007...
-
Page 41: Default Configuration Settings
Appendix B Default Configuration Settings This appendix provides the default settings for the NETGEAR Model GSM7328S, GSM7352S, and GSM7328FS switches. Table B-1. Default Configuration Settings Features Default Setting Port speed Auto-negotiation Port duplex Auto-negotiation Flow control (half duplex) Enabled Flow control (full duplex) - Page 42 Managed Stackable Layer 3 Switches GSM7328S, GSM7352S and GSM7328FS Hardware Instal- Table B-1. Default Configuration Settings (continued) Features Default Setting IP routing Disabled Disabled MAC address aging 300 seconds OSPF Disabled SNMP community public (read-only access), private (read/write access) DHCP Server Disabled VLAN Ingress filtering Enabled...
- Page 44 NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA February 2007...