T731 Operating Instructions - Asko T711 Use And Care Manual

T731 OPERA T731 OPERATING INSTR T731 OPERA T731 OPERA T731 OPERA TING INSTR TING INSTR TING INSTRUCTIONS TING INSTR
WARNING! To reduce the risk of electric shock or injury to persons, read the "Important Safety
Instructions" section on page 2 before operating this appliance.
THE CONTR THE CONTROL P THE CONTR OL P OL PANEL OL P
THE CONTR THE CONTR OL P
Power Button
Turns power to
the machine on
and off.
Power Indicator
Light
Glows when the
power is turned on.
Program Knob
Turn to select a program.
PO PO WER BUTT WER BUTT ON ON
PO POWER BUTT PO WER BUTT WER BUTTON ON ON
The Power button turns the power to the machine on
and off. When the power is on, the power indicator light
glows red. The power must be on before you can start
the machine.
PR PROGRAM KNOB PR PR PR OGRAM KNOB OGRAM KNOB OGRAM KNOB OGRAM KNOB
Turn this knob to select a program. The programs are
described on the following page.
12:00 Position – This is where the line on the knob
aligns with the line above the knob. When the knob is in
this position, "00" displays on the LED to indicate no
program has been chosen.
STAR ST ST ST ST AR ART BUTT AR AR T BUTT T BUTTON T BUTT T BUTT ON ON ON ON
After you have selected a program and the desired
options, press this button to start the dryer. The red
indicator light next to the Start button will come on. The
indicator light will go off when the program ends or has
been cancelled.
ST ST OP B OP B UTT UTT ON ON
STOP B ST ST OP BUTT OP B UTT UTTON ON ON
You can stop or cancel a program by pressing and
holding the Stop button until the dryer stops. When you
press Start, the program will start from the beginning.
INTERRUPTING OR CANCELLING INTERR INTERR INTERR INTERR UPTING OR CANCELLING UPTING OR CANCELLING UPTING OR CANCELLING UPTING OR CANCELLING
A PR A PR OGRAM OGRAM
A PROGRAM A PR A PR OGRAM OGRAM
To interrupt a program, simply open the door. The dryer
will stop tumbling automatically. To continue the
program, close the door and press Start. The program
will continue from the point it was interrupted.
To cancel a program, press and hold the Stop button
Page 14
UCTIONS UCTIONS UCTIONS UCTIONS
ANEL ANEL ANEL
ANEL
Iron dry
Timed dry
Power
Air fluff
Time set
Wrinkle free
Delay
Temperature
Signal
Quick cool-down
LED Window
Displays program number, dry time
selected, remaining program time, etc.
Programs
Heavy
Normal
Delicate
Option Buttons
Press to select a
program option.
until the Stop indicator light goes off (approximately 3
seconds). You will have to reselect a program and press
Start to restart the dryer.
LED WINDOW LED WINDOW
LED WINDOW LED WINDOW LED WINDOW
The LED window displays the program number for the
Sensidry programs, as illustrated below:
The corresponding program numbers are:
Heavy = P1
Normal = P2
When you select Timed Dry, the LED displays the
number of minutes selected, plus the cool-down time,
as illustrated below:
When you select Air Fluff, the LED displays the number
of minutes selected, as illustrated above. With both
programs 5 and 6, as the program advances, the LED
displays the remaining time.
"End" on the LED indicates the program is complete.
"C" indicates the program is in the cool-down cycle.
Start Button
Press to start a
program.
Stop Button
Press to stop a
program.
P1
Delicate = P3
Iron Dry = P4
20