Menu Modes No 077 - No 091 - Yaesu FT-897D Operating Manual

M O
ENU PERATION
MENU MODE No•077 [ SCAN MODE ]
Function: Selects the desired Scan-Resume mode.
Available Values: TIME/BUSY/STOP
Default: TIME
This Menu Item allows you to select your favorite method
of scan-restart after the scanner has stopped on an incoming
signal (when the squelch opens).
TIME: The scanner will hold for a fixed length of time, set
via MENU MODE No-078 [ SCAN RESUME ] , then
resume whether or not the other station is still trans-
mitting.
BUSY: The scanner will hold until the signal disappears, then
will resume after one second.
STOP: The scanner will stop when a signal is received, and
will not restart.
MENU MODE No •078 [ SCAN RESUME ]
Function: Sets the delay time for scanning resumption.
Available Values: 1 ~ 10 (sec)
Default: 5
MENU MODE No •079 [ SPLIT TONE ]
Function: Enables/disables split CTCSS/DCS cording.
Available Values: OFF/ON
Default: OFF
MENU MODE No - 080 [ SQL/RF GAIN ]
Function: Selects the configuration of the front panel's SQL/
RF knob.
Available Values: RF-GAIN/SQL
Default: Depends on transceiver version.
MENU MODE No- 081 [ SSB MIC GAIN ]
Function: Adjusts the microphone gain level for the SSB
mode.
Available Values: 0 ~ 100
Default: 50
MENU MODE No- 082 [ SSB STEP ]
Function: Selects the tuning steps for the MEM/VFO CH
knob on the SSB mode.
Available Values: 1kHz/2.5kHz/5kHz
Default: 2.5kHz
MENU MODE No- 083 [ TONE FREQ ]
Function: Setting of the CTCSS Tone Frequency.
Available Values: 50 Standard CTCSS tones
Default: 88.5 Hz
MENU MODE No- 084 [ TOT TIME ]
Function: Select the Automatic Power Off time.
Available Values: OFF/1 ~ 20 (min)
Default: OFF
Page 62
MENU MODE No •085 [ TUNER/ATAS ]
Function: Selects the device (FC-30 or ATAS-100/-120)
to be controlled via the front panel's [ A ]( TUNE ) key.
Available Values: OFF/ATAS(HF)/ATAS(HF&50)/
ATAS(ALL)/TUNER
Default: OFF
The [ A ]( TUNE ) key is disabled.
OFF:
ATAS ( HF ) :
The [ A ]( TUNE ) key will activate the optional
ATAS-100/-120 on the HF amateur bands.
ATAS ( HF&50 ) : The [ A ]( TUNE ) key will activate the optional
ATAS-100/-120 on the HF amateur bands
and 50 MHz amateur band.
ATAS ( ALL ) :
The [ A ]( TUNE ) key will activate the optional
ATAS-100/-120 on the all amateur bands
which enable to the FT-897D transceiver.
The [ A ]( TUNE ) key will activate the optional
TUNER:
FC-30.
MENU MODE No •086 [ TX IF FILTER ]
Function: Selects the Transmit IF filter.
Available Values: CFIL/FIL1/FIL2
Default: CFIL
MENU MODE No•087 [ VOX DELAY ]
Function: Sets the "hang time" for the VOX circuitry.
Available Values: 100 ~ 3000 (ms)
Default: 500 (ms)
MENU MODE No- 088 [ VOX GAIN ]
Function: Sets the gain of the VOX circuitry's input audio
detector.
Available Values: 1 ~ 100
Default: 50
MENU MODE No•089 [ XVTR A FREQ ]
Function: Allows an arbitrary frequency to be set on the dis-
play, to allow direct frequency readout during transverter op-
eration; can also be used to account for frequency conversion
inaccuracies when a known reference frequency is known.
Available Values: 00,000,00 ~ 99,999,99 (kHz)
Default: Current VFO frequency.
MENU MODE No •090 [ XVTR B FREQ ]
Function: Allows an arbitrary frequency to be set on the dis-
play, to allow direct frequency readout during transverter op-
eration; can also be used to account for frequency conversion
inaccuracies when a known reference frequency is known.
Available Values: 00,000,00 ~ 99,999,99 (kHz)
Default: Current VFO frequency.
MENU MODE No •091 [ XVTR SEL ]
Function: Enable/disable the Transverter function.
Available Values: OFF/XVTR A/XVTR B
Default: OFF
Disables the Transverter operation feature.
OFF:
X VTR A: Activates the transverter operation feature.
The display frequency may be set via MENU No-
089 [ XVTR A FREQ ] .
X VTR B: Activates the second transverter operation display.
The display frequency may be set via MENU No-
090 [ XVTR B FREQ ] .
FT-897D O M