Menu Modes No 015 - No 029 - Yaesu FT-897D Operating Manual

MENU MODE No •015 [ CAR LSB R ]
Function: Sets the Rx Carrier Point for LSB.
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No •016 [ CAR LSB T ]
Function: Sets the Tx Carrier Point for LSB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No •017 [ CAR USB R ]
Function: Sets the Rx Carrier Point for USB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No•018 [ CAR USB T ]
Function: Sets the Tx Carrier Point for USB
Available Values: –300 ~ +300 Hz
Default: 0 Hz
MENU MODE No•019 [ CAT RATE ]
Function: Sets the transceiver's circuitry for the CAT baud
rate to be used.
Available Values: 4800bps/9600bps/38400bps
Default: 4800bps
MENU MODE No •020 [ CAT/LIN/TUN ]
Function: Selects the device which is connected to the
/LINEAR jack on the rear panel.
Available Values: CAT/LINEAR/TUNER
Default: CAT
MENU MODE No •021 [ CLAR DIAL SEL ]
Function: Defines the "control" knob to be used for setting
of the clarifier offset frequency.
Available Values: CLAR, M/V, MAIN (Clarifier/Selector/
Main Dial Knobs)
Default: CLAR
MENU MODE No- 022 [ CW AUTO MODE ]
Function: Selects whether the KEY jack shall be "Enabled"
or "Disabled" while using the SSB/FM modes.
Available Values: ON/OFF
Default: OFF
OFF: The KEY jack is enabled on the CW mode only.
The KEY jack is enabled on all modes (SSB mode:
ON:
A1, FM mode: F2). Thus, on SSB, you can ask a
station for a CW QSO without having to change your
FT-897D's Mode selection, if Menu #022 is set to
"On."
MENU MODE No•023 [ CW BFO ]
Function: Sets the CW carrier oscillator injection side on
the CW mode.
Available Values: USB/LSB/AUTO
Default: USB
USB: Injects the CW carrier oscillator on the USB side
LSB: Injects the CW carrier oscillator on the LSB side
AUTO: Injects the CW carrier oscillator on the LSB side
while operating on the 10 MHz band and below, USB
side while operate on the 10 MHz band and up.
FT-897D O M
M
ENU
MENU MODE No- 024 [ CW DELAY ]
Function: Sets the receiver recovery time during pseudo-
VOX CW semi-break-in operation.
Available Values: FULL/30 ~ 3000 msec
Default: 250 msec
The recovery time may be adjusted in steps of 10 msec. A
longer delay may be preferable if you pause frequently while
sending.
MENU MODE No•025 [ CW KEY REV ]
Function: Sets the keyer paddle's wiring configuration.
Available Values: NORMAL/REVERSE
Default: NORMAL
NORMAL: Keyer paddle polarity is normal. The "tip" plug
connection produces dots, and the "ring" plug
connection produces dashes.
REVERSE: Keyer paddle polarity is inverted. The "tip"
paddle produces dashes, and the "ring" paddle
produces dots.
MENU MODE No •026 [ CW PADDLE ]
Function: Enables/disables CW keying by the microphone's
[UP]/[DWN] keys.
Available Values: ELEKEY/MICKEY
Default: ELEKEY
When this Menu Item is set to "MICKEY," press the
microphone's [UP] key to send a "dot," and press the
microphone's [DWN] key to send a "dash" (while the built-
in electronic keyer is engaged).
MENU MODE No- 027 [ CW PITCH ]
Function: Setting of the pitch of the CW sidetone, BFO
offset, and CW filter center frequencies.
Available Values: 400 ~ 800 Hz
Default: 700 Hz
The CW pitch may be adjusted in steps of 100 Hz.
MENU MODE No•028 [ CW QSK ]
Function: Selects the time delay between when the PTT is
keyed and the carrier is transmitted during QSK operation
when using the internal keyer.
Available Values: 10/15/20/25/30 ms
Default: 10 ms
Note: If you select "25 (or 30) ms," please do not attempt
to set Menu [No-030 CW SPEED] to a speed faster than
"50 (42) wpm," as the delay will make it impossible to trans-
mit.
MENU MODE No- 029 [ CW SIDE TONE ]
Function: Setting of the CW sidetone volume level.
Available Values: 0 ~ 100
Default: 50
O
PERATION
Page 57