FUTABA FP-8SSHP Instruction Manual page 20

H. Servo reversing switches
These switches reverse the direction of the servos.
They are very convenient when connecting the linkage.
Rudder
Throttle
Elevator
Aileron
NORM position
: Forward
REV position
: Reverse
I. ATV/FS button
•These two pushbutton switches are used for servo
deflection angle setting of ATV, FS or HOLD func-
tion; servo test start & stop; reset; battery FS memo-
ry set, etc.
18
[32]This pushbutton switch is used when:
1 Making the ATV servo deflection angle larger.
2 Turning the FS function on.
3 Starting the servo test.
—[33] This pushbutton switch is used when:
1 Making the ATV servo deflection angle smaller.
2 Turning the HOLD function on.
3 Stopping the servo test.
When button [32] and [33] are pressed at the same time,
reset or battery FS memory setting is possible. At this
time, lamp [A] of monitor lamps [24] goes out momen-
tarily so that setting can be monitored.
Fig. 49
CH8 switch
channel
CH7 lever channel
CH6 pitch control
CH5 switch channel
•USING ATV (Aileron ATV
taken as an example)
1 First, set switch [K] [35] to the ATV side.
2 Next, set CHANNEL SELECT switch
1 (aileron) position.
3 Set the transmitter and receiver power switches to
ON, and check the operation of the servos.
4 Set the aileron stick for full right rudder, hold it in
that position, and set the aileron right throw to the
desired angle by pressing buttons [33] and [32].
5 To set aileron left, hold the aileron stick in the full
left position and set the servo throw with buttons
[33] and [32].
(ATV can be adjusted in 64 steps. ATV can be con-
tinuously varied by pressing and holding the but-
ton for more than 1.5 seconds.)
6 For the other channels, select the channel with the
CHANNEL SELECT switch [J] [34] and operate
ATV.
7 At the end of adjustment, set switch [K] [35] to the
center OFF position and set switch [J] [34] to OFF
position.
8 This ATV function is memorized even if the power
switch is set to off, the ATV function is lost if the
transistor Nicd is fully discharge.
9 When clearing the ATV, set switch [35] to RESET
and switch [34] to position 2 and press buttons [32]
and [33] simultaneously. ATCs of all channels are
cleared and servos deflect their 100% angle.
ATV SETTING
Press button [32] and
holding the aileron stick in the
full position.
Switch switches [J] [34] and [K] [35]
HOW TO USE FS (Fail Safe)
(Throttle channel as an example.)
1 First, set switch [K] [35] to FS S E L E C T .
2 Set the transmitter and receiver power switches to
ON, and check the movement of each servo.
3 Next, while switching the channel select switch [34]
from 1 to 8 in order, set the channels to be used
with FS, with button [32] and set the channels to
be used with HOLD, with button [33]. In this ex-
ample, set 3 ( t h r o t t l e ) to FS with button [ 3 2 ] .
4 Set the throttle lever to the slowest position, and
press the FS set button [36] on the back of the
transmitter.
5 The 1 — 4 above set low throttle for the FS
function. After setting FS function, turn switch
[35] and [34] to OFF. Test fail safe by turning the
transmitter power switch to OFF.
[J] [34] to the
Fig. 51
[33] while