Advertisement
SET CONTENTS AND RATINGS
(Specifications are subject 10 change without prior notice.)
CONOUEST
FP-6NLK
Transmitter
FP T6NLK x 1
F P R 7 H x 1
Receiver
FP-S38 x 4
Servo
NR 4M x
NiCad Battery
SSW-Hx
Switch
Charger. Frequency flag
Others
Mounting screw.
TRANSMITTER FP-T6NLK/T4NL CONTROLS
Fig. 1 shows the name of each part of the transmitter.
Memorize the position and operation of each
switch and control.
Elevator dual trimmer
(6NLK only)
Landing gear switch
(5ch) (6NLK only)
Elevator
dual switch
(6NLK only)
Level meter
Throttle trim
lever
Rudder
trim lever
Rudder
Throttle
Nonslip adjustable
lever head
In the following descriptions, all the servo reversing switches
are assumed to be in the normal position. When they are in the
reverse position, operation is the opposite of that described.
Aileron
Aileron operation
Elevator operation
Elevator
Throttle
Throttle operation
Rudder
Rudder operation
Landing gear switch
(6NLK only)
Raising and lowering the
landing gear.
6chCH switch (6NLK only)
Use for controlling model
airplane flaps, etc. The
servo is operated at the
and
positions. The
position is off.
TRANSMITTER FP-T6NLK /T41ML
Operating System
CONQUEST
FP-4NL
FP-T4NL x 1
FP.R4Fx 1/FP-R4HX 1
FP S38 x 3
Transmitting frequency : 72MHz bands, 75MHz
1
1
Modulation system
. Spare horn,
Power requirement
Current drain
Power switch
Aileron
Elevator
The servo is connected
to 6 channels.
2 stick,servo reverse
Aileron, Elevator dual
switch. Landing gear
switch (5ch) & switch
(6ch) 6NLK only
bands
: AM
: 9, 6V, NiCad battery
(NT-8LP)
: 190mA
Antenna
Handle
Aileron
dual
trimmer
Aileron trim lever
Elevator trim lever
Throttle trim lever
Rudder trim lever
Aileron dual rate switch (6NLK only)
Aileron dual rate ON-OFF switch. When set to the upper
position, dual rate is turned on, and when set to the lower
position, dual rate is turned off.
Aileron dual rate trimmer (6NLK only)
This trimmer sets the aileron travel when the aileron dual
switch is set to on. When the dual switch is set to ON, the
servo throw can be set to an arbitrary angle smaller than
when the dual switch is OFF (normal) as shown in the
figure. Use the throw matched to the aircraft and the
Fig. 2
maneuvers to be performed.
RECEIVER FP-R7H / R 4 F / R4H
Receiving frequency
: 72MH/ bands, 75MHz bands
Crystal replacement system: Frequency can be changed
Intermediate frequency
: 455kHz
Power requirement
: 4, 8V, NiCad battery
Current drain
: 4.8V, 10mA
R7H 1.6x 2.6 x 0.8 inch
(41 x 69 x 21 mm)
R4F 1.6 x 2.3 x 0.7 inch
Dimensions
(40.2 x 58.5 x 19 mml
R4H 1.26x 2.05 x 0 77 inch
(32 x 52 x 19.4 mm)
Receiving range
: 550 yards (500m) on the
SERVO FP-S38
Control system
: + pulse width control
Operating angle
: One side 45° or more
(including trim)
Power requirement
: 4.8V ~ 6V
Current drain (IDLE) : 6.0V, 8mA
Output torque
: 34.8oz.in (2.5kg-cm)
Operating speed
: 0.23sec/60°
Dimensions
: 1.59 x 0.79 x 1.38 inch
(40.5 x 20 x 35.3mm)
Weight
: l.44oz (41g)
6th CH switch (6NLK only)
Aileron dual switch (6NLK only)
Neck strap bracket
Elevator
trim lever
Aileron
trim
lever
Charging
jack
Transmitter
NiCad battery
NT-8LP
23) Battery cover
Aileron trimmer
Elevator trimmer
Throttle trimmer
Rudder trimmer
within the same frequency
band by changing the pre-
cision crystal.
Common use with servo
R7H
1 7oz(50g)
R4F
Weight
1.6oz (46g)
R4H
1.06oz (30g)
ground. 1,100 yards
(1,000m) in the air.
(at the best conditions)
Servo reversing
switches
Fig. 1
Advertisement
