Cvp-309/307: Keyboard Stand Assembly - Yamaha Clavinova CVP-307 Owner's Manual

CVP-309/307: Keyboard Stand Assembly

CAUTION
• Be careful not to confuse parts, and be sure to install all
parts in the correct direction. Please assemble in accor-
dance with the sequence given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated below.
Use of incorrect screws can cause damage.
• Be sure to tighten up
Have a Phillips-head (+) screw-
all screws upon com-
driver ready.
pleting assembly of
each unit.
• To disassemble,
reverse the assembly
sequence given below.
1
Remove all parts from the box. Confirm that all
parts shown in the illustration are provided.
Front leg (left) Rear leg Front leg (right)
Pedal box
AC power cord
Protective pad
(CVP-309)
2
With the key cover closed and the keyboard side
on the bottom, lean the unit against the wall.
Please do not touch the speaker
net. Doing so may damage the
speaker inside.
Be sure to position the keyboard side on the bottom.
CAUTION
• Be careful not to pinch your fingers.
• The top part of the music rest is not fixed. When you lean
the unit against the wall, support the music rest with your
hand so that the music rest will not fall.
CAUTION
• Do not place the main unit
with the rear side facing
down.
• Do not lay the main unit
upside-down on the floor.
CAUTION
To prevent the
key cover from
accidentally
opening during
assembly, press
down on the
key cover, mak-
ing sure that
the sheet
(shown) remain
in place.
Bundled pedal
cord inside
5x18 mm fixing
screws × 14
CAUTION
Incorrect
Incorrect
(CVP-309)
Protective pad
Floppy disk drive
Floppy disk drive
1 Spread a large soft cloth such as a blanket on the
floor in front of the wall.
2 Place the main unit on the soft cloth with its
keyboard side facing the wall.
3 Place a protective pad on the soft cloth, so that,
when you place the main unit on the floor with its
keyboard side touching the floor, the pad comes
under the keyboard side, and is located about 10cm
(a little more than four inches) to the high key side
from the floppy disk drive. The pad will protect the
floppy disk drive so that it will not be damaged by
touching the floor.
4 Raise the rear of the main unit until it leans
against the wall. When raising the unit, place the
keyboard side at the bottom and make it sit on the
protective pad.
Be careful not to allow the unit to fall or slip.
Also, insert the soft cloth between the main unit
and the wall to protect the unit from being
damaged by hitting the wall or any other object.
CAUTION
Be sure to use a protective pad to avoid a damage to the
floppy disk drive. If the drive touches the floor when you
raise the unit to lean it against the wall, too much pressure
may be applied to the drive, possibly causing serious dam-
ages to the drive.
(CVP-307)
Spread a large soft cloth, such as a blanket, on the floor.
Place the unit on the cloth with the keyboard side on
the bottom and lean the unit against the wall so that the
unit will not fall or slip. Place a soft cloth against the
wall to protect the instrument and wall from scratches.
3
Attach the front legs.
Front leg (right)
1 Fix the front right
leg to the bottom
surface of the unit
using two screws.
3 Fix the front left leg in the same way.
If the screw holes do not align, loosen the other screws and
adjust the position of the front leg.
4(CVP-309) Slowly tilt the main unit forward
until front legs reach the floor.
CVP-309/307 Owner's Manual
Large soft cloth
Protective pad
Front leg (left)
2 Fix the front right leg
to the speaker box
using two screws.
209