The Headphones Menu; The Network Settings Menu - NAIM UNITI - Reference Manual

Na im Un it i Setu p
frequency performance of large (full bandwidth) speakers.
Large
Select when no subwoofer is used (the NaimUniti
subwoofer output is switched off when Large is selected).
Select Small+Sub when a subwoofer is used to provide
the low frequency component of a speaker system
incorporating small (restricted bandwidth) satellite
speakers. When Small+Sub is specified, a 100Hz high-pass
filter is applied to the NaimUniti speaker output signal.
The speaker Max. Volume
maximum allowed volume, and the channel balance
respectively.
4. 5 The Head phone s M en u
The Headphones setup menu
enables the Max. Volume
parameter to be specified:
Parameter Options
Max. Volume:
0 to 100 (adjust
using handset
or

4.6 The Network Settings Menu

The Network Settings menu
enables NaimUniti network
parameters to be customised
to suit the router and network.
The options are tabulated and
described in the following sections:
Parameter Options
Name: User definable (text entry)
Default: Uniti-xxxx
Wireless: Not Used / Wireless Network Names
Status: Connected / No Signal / Login Failure /
Busy / Etc.
DHCP:
Yes / No
The Name parameter enables the NaimUniti's default
network name to be changed.
The Wireless parameter enables a wireless network to be
chosen and joined. See Section 4.6.1 below for detailed
wireless set up notes.
Status
Network displays the current network connection
status.
The DHCP parameter enables the NaimUniti network
settings to be modified. In most cases, specifying
leaving NaimUniti set to DHCP, will be the appropriate
option. See Section 4.6.2 below for notes on non-DHCP
network connection.
Note: Devices installed on a network have an IP address
through which they are identified by all the other items
on the network. DHCP is a set of rules that enable the
automatic allocation of addresses as items are connected
(or switched on while connected) to the network.
NaimUniti is set up by default to use DHCP.
12
and Balance parameters specify
Headphones
4Max. Volume:
6
5 keys)
Network Settings
4Name:
Wireless:
Status: Not Connected
DHCP
Note: If NaimUniti is connected to the network both
wirelessly and via Ethernet (wired), the Ethernet connection
will take priority.
4.6.1 Wireless Network
Connection Set Up
If the Wireless
selected in the Network Settings
menu the Select Network menu
will display a list of the available
networks. An option not to use a wireless connection is
also provided. Use the handset
to scroll through the list and the
network.
Note:
NaimUniti is compatible with most commonly used
1/1
Wi-Fi standards. Routers that support 802.11b and 802.11g
100
will work, however those with 802.11g compatibility are
recommended for best results.
Note: As with any wireless network hardware, NaimUniti
connection reliability will be affected by both network
router performance and Wi-Fi signal quality. To minimise the
possibility of poor connection reliability, NaimUniti should be
connected to network audio sources by no more than one
wireless "leg". Other "legs" necessary between NaimUniti
1/4
and the network audio sources should be wired.
Uniti-0131
Note: NaimUniti cannot connect to a "hidden" wireless
Not Used
network.
Yes
If the selected network is secure
and requires a passphrase or
access key to join, NaimUniti will
display an alert message. Pressing
the handset
open a text entry screen for entry
of the passphrase or access key.
Use the handset
keys to enter the passphrase or
access key taking care to ensure
that the letter case is correct.
Press the handset
when text entry is complete. In
the illustration the passphrase is
"flatfish".
If the network is successfully
joined NaimUniti will display a
confirmation screen.
Yes and
If an incorrect passphrase or
access key is entered NaimUniti
will display an alert message.
Note: As a security measure,
a router may also require the
NaimUniti's MAC address to be entered before allowing
it to join the wireless network. This type of security feature
is known as 'MAC address filtering'. The NaimUniti MAC
address is shown in the 'Factory settings > System Status'
page.
Select Network
<Don't Use Wireless>
parameter is LingNet
4GreenNet
TomNet
up ( 5 ) or
ok/list key to select a
Now enter your wireless
passphrase or access key.
Press OK to continue
ok/list key will then
flatfish
numeric/text
Press OK to confirm
ok/list key
Connected
Press OK To Finish
Can't Login
Press OK To Re-Try
3/6
down ( 6 ) keys
abc
flatfish
|