Aiwa Z-R555 Operating Instructions Manual page 13

:r
' '"
6,8
1,8
4
5
3,7
The Al edit recording function enables CD recording without
worrying about tape length and track length. When a CD is
inserted, the unit automatically calculates the total track length,
If necessary, the order of tracks is rearranged so that no track is
cut short.
(Al: Artificial Intelligence)
1
2
?3
4
5
Insert the tape into Deck 1.
Insert the tape with the side to be recorded on first facing out
from the unit, and wind up the tape with +.
Press CD and load the disc(s).
Press EDIT/CHECK once while pressing SHIFT
on the remote control.
"EDIT" and "Al" are displayed.
EDIT
When "PRGM" is displayed, press EDIT/CHECK while
pressing SHIFT again.
Press one of DISC DIRECT PLAY 1-5 to select a
disc.
To select disc
4
or
5
from the remote control, press DISC
DIRECT PLAY 4 or 5 while pressing SHIFT.
Press numbered buttons O-9 on the remote
control to designate the tape length.
10 to 99 minutes can be specified,
Example: When using a 60-minute tape, press 6 and O.
In a few seconds, the tracks to be recorded on each side of
the tape are determined.
U, M
or MULTI JOG are also available to designate
the tape length.
Remaining time Programmed
Tape length
of recording
tracks for side A
f
6
7
8
Press on Deck 1 to start recording on the first
B
,',~,,
side.
,7 ,-
=
flashes for 10 seconds, and then CD play and recording
:,~g
;F,gg:;
of edited tracks for the first side start simultaneously. When
$
;*,, ,1, ":
the end of the tape is reached, Deck 1 enters the recording ""' ,
stop mode. After entering the recording stop mode go to step
;~
7.
-p
Press EDiT/CHECK while pressing SHIFT on the
remote control to display the program for the
second recording.
"B" is displayed.
Turn over the tape in Deck 1 and press @ to start
recording on the second side.
To stop
recording
Press WA on Deck 1.
Recording and CD play stop simultaneously.
To
clear the edit program
Press WCLEAR twice in
the stop mode so that "EDIT" disappears
on the display, or press
A OPEN/CLOSE.
To
check the order of the programmed track numbers
Before recording, press
EDIT/CHECK while pressing SHIFT on
the remote control to select side A or B, and press 4M or -
repeatedly.
Tape side Programmed track numbers
Track number Program number
To add tracks from other discs to the edit program
If there is any time remaining on the tape after step 5, you can
add tracks from other discs in the CD compartment
1
2
3
4
Press
EDIT/CHECK while pressing SHIFT on the remote
control
to select side A or B.
Press one of DISC DIRECT PLAY 1-5 to select a disc.
To select disc 4 or 5 from the remote control, press DISC
DIRECT PLAY 4 or 5 while pressing SHIFT.
Press numbered buttons on the remote control to select the
tracks.
A track whose playing time is longer than the remaining time
cannot be programmed.
Repeat steps 2 and 3 to add more tracks.
Time on cassette tapes and editing time
The actual cassette recording time is usually a little longer than
the specified recording time printed on the label. This unit can
program tracks to use the extra time. When the total recording
time is a little longer than the tape's specified recording time
after editing, the display shows the extra time (without a minus
mark), instead of the time remaining on the tape (with the minus
mark).
The Al edit recording function cannot be used with discs
containing 31 tracks or more.
Tape side
A: First recording side
B: Second recording side
ENGLISH 12