Table of Contents
Advertisement
Chapter 6 Using Pedals to Control the Effects
Setting the Operation for an External MIDI
Device (CC#7, CC#80, CC#1 Function)
These settings are applied to the entire GT-PRO, controlling
the GT-PRO by means of Control Change messages from an
FC-200 or other external MIDI device connected to the GT-
PRO via MIDI.
The following describes the settings for Control Change No.
7 (CC#7), No. 80 (CC#80), and No. 1 (CC#1).
When Using the FC-200
When the FC-200 is set to its default settings, the
correspondence between CC#7, CC#80, and CC#1 and
the FC-200's controllers is as shown below.
CC#7:
EXP pedal
CC#80:
CTL pedal
External expression pedal connected to the
CC#1:
FOOT SW/EXP 1 jack.
fig.06-0070
1. Press [SYSTEM].
2. Press PARAMETER [
"CC#80 Func," or "CC#1 Func" is displayed.
fig.06-0080d
3. Use the PATCH/VALUE dial to set how the Control
Change messages are used.
4. Repeat Steps 2 and 3 as needed.
5. Press [EXIT] to return to the Play screen.
64
3
2
1
5
] [
] so that "CC#7 Func,"
CC#7
Value
Explanation
The pedal normally is used as a "foot vol-
ume" pedal. When Pedal Wah (p. 36) or
Auto
Pedal Bend (p. 47) is switched on, the CC#7
then automatically functions as a "pedal
wah" or "pedal bend" pedal.
When Pedal Wah and Pedal Bend are switched off, this automatical-
ly functions as a "foot volume" pedal.
The pedal is used as the controller set in As-
Assignable
sign (p. 66) for each patch.
Foot Volume
The pedal functions as a "foot volume" pedal.
Patch Level
The pedal is used as the patch level controller.
The pedal is used as a "pedal wah" pedal
Pedal Wah
when Pedal Wah is switched on.
The pedal is used as a "pedal bend" pedal
Pedal Bend
when Pedal Bend is switched on.
If operating the expression pedal or FC-200 EXP pedal
with the EXP1 function, EXP2 function, and CC#7
function all set, be sure to have different functions
assigned to each pedal.
If the same function is assigned to different pedals,
operation normally functions according to the value of
the last pedal adjusted, but may not work as intended
when Assign Hold (p. 99) is set to "On."
CC#80
Value
Explanation
The pedal functions as the type of controller
Assignable
set with Assign (p. 66) in each individual
patch.
Preamp Ch A/B
Switches between Preamp channel A and B.
Solo On/Off
Switches the Preamp SOLO on and off.
FX-1 On/Off
Switches the FX-1 on and off.
Comp On/Off
Switches the COMP on and off.
Wah On/Off
Switches the WAH on and off.
Loop On/Off
Switches the LOOP 1/2 on and off.
Switches the OVERDRIVE/DISTORTION
OD/DS On/Off
on and off.
Switches the PREAMP/SPEAKER on and
Preamp On/Off
off.
EQ On/Off
Switches the EQ on and off.
FX-2 On/Off
Switches the FX-2 on and off.
Delay On/Off
Switches the DELAY on and off.
Chorus On/Off
Switches the CHORUS on and off.
Reverb On/Off
Switches the REVERB on and off.
Pre Loop On/Off
Switches the PRE LOOP on and off.
Amp Ctl1 On/Off
Switches the AMP CTL 1 on and off.
Amp Ctl2 On/Off
Switches the AMP CTL 2 on and off.
Switches the Manual Mode (p. 85) on and
MANUAL On/Off
off.
TUNER On/Off
Switches the TUNER/BYPASS on and off.
Master BPM (TAP)
Used for tap input of the Master BPM.
Delay Time (TAP)
Used for tap input of the delay time.
Advertisement
Table of Contents
